Oliver Milan MI50 User manual

Installation Instructions
This basin is warranted to be free from manufacturing defects for a period of:
Lifetime, stainless steel bowl
This warranty does not cover against normal wear and will be voided if the
product is misused or not installed in accordance with these instructions.
In the event this product is rendered obsolete and a replacement product is required,
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be acceptable quality and the failure does
not amount to a major failure.
For full warranty information, visit: https://oliveri.com.au/service-and-warranty
If the basin requires servicing, please contact your installer (preferably the one who
All warranty claims must be directed to our Warranty Service Agent. If the Warranty Service
Agent finds that the basin is not faulty, they reserve the right to pass on any callout fee to
the householder.
WARRANTY
SINK SERVICE
oliveri.com.au
Oliveri Solutions Pty Ltd reserves the right to supply a product of equal substitution at
installed it). If the installer is satisfied that the problem is not due to poor installation,
contact Oliveri’s nominated Warranty Service Agent. For details visit:
https://oliveri.com.au/service-and-warranty
TF12a - MI50 Installation Instructions
Check the product for damage, if the product is damaged return to store of purchase.
Check the product is complete with all components required to install.
This product is to only be installed by a licensed plumber, failing to do so will void
the warranty.
This product is to be installed as per Australian Standard and local authority requirements
Inset Basin installation:
Installation Instructions
INSTALLATION INSTRUCTIONS FOR INSET BASIN
Milan
Pop-up waste, 1 year, parts and labour.
their discretion.
THIS BASIN MUST BE INSTALLED BY A LICENSED PLUMBER IN
ACCORDANCE WITH LOCAL REGULATIONS.
Scratching during use does not constitute a product or manufacturing fault.
1. This basin is supplied with a cut-out template. Due to manufacturing variations
it is recommended you cross check the cut-out template dimensions against
the physical basin dimensions and adjust the cut-out size as, or if required.
2. Using the template dimensions, locate the basin cut-out in the desired position on
the benchtop.
3. Prior to cutting the hole, check to ensure the cut-out will not interfere with
drawers or internal walls of the vanity cabinet.
NOTE: We recommend installing the basin so the Oliveri logo is positioned
towards the back of the bench, and/or under the tap.
4. Cut the hole into the vanity cabinet top.
5. Fit the basin into the cut-out hole to ensure the basin fits correctly and no further
adjustment of the cut-out hole is required.
6. Prior to installing the basin, it is recommended the tapware and waste are fitted
to the basin for ease of assembly.
7. Prior to fitting the basin to the bench top, run a plumbers grade silicone seal
around the cut-out hole.
8. Insert the basin into the bench top cut-out and align so the basin is square to
the vanity cabinet top.
9. Apply a bead of neutral cure silicone around the outer edge of the basin
to prevent water going under the basin. Remove any excess silicone and allow
the silicone to dry before proceeding with waste pipe installation.
10. Connect basin to drainage system as per Australian standards and local authority
requirements.
MI50
Rectangular Stainless Steel Inset Basin
CARE & MAINTENANCE
Surfaces should be cleaned with a soft cloth and warm soapy water. Rinse and dry after
cleaning. Under no circumstances should abrasive or acid based cleaning products be used.

Installation Instructions
TF12a - MI50 Installation Instructions
1. This basin is supplied with a cut-out template. Due to manufacturing variations
it is recommended you cross check the cut-out template dimensions against
the physical basin dimensions and adjust the cut-out size as, or if required.
2. Using the template dimensions, locate the basin cut-out in the desired position on
the benchtop.
3. Prior to cutting the hole, check to ensure the cut-out will not interfere with
drawers or internal walls of the vanity cabinet.
NOTE: We recommend installing the basin so the Oliveri logo is positioned
towards the back of the bench, and/or under the tap.
4. Cut the hole into the vanity cabinet top.
5. Fit the basin into the cut-out hole to ensure the basin fits correctly and no further
adjustment of the cut-out hole is required.
6. Prior to installing the basin, it is recommended the tapware and waste are fitted
to the basin for ease of assembly.
7. Prior to fitting the basin to the bench top, run a plumbers grade silicone seal
around the cut-out hole.
8. Insert the basin into the bench top cut-out and align so the basin is square to
the vanity cabinet top.
9. Apply a bead of neutral cure silicone around the outer edge of the basin
to prevent water going under the basin. Remove any excess silicone and allow
the silicone to dry before proceeding with waste pipe installation.
10. Connect basin to drainage system as per Australian standards and local authority
requirements.
Technical Data
70
130
R10
3
370 350
ø48
380
R20
10
R10
400
358
388
R10
Benchtop cut out template: