OLS PPA Int'l OLSMSRGB User manual

Remote Control (Remote is infrared, meaning line-of-sight)
•Push the ON button to turn the unit on and the OFF button to turn the unit off
•To operate:
oTurn the unit ON
oPress 1 of any of the 16 colored buttons to change color
oDim or Brighten using :
Bright Dim
oPress one of these buttons to use the pre-programmed mode for your lighting display
oSingle color FADE – Press desired color first, then press FADE
One Year Limited Warranty:
PPA International, Incorporated warrants this product to be free of defects in materials or workmanship for one year.
Warranty does not include damage resulting from accidents, mususe, or cutting of LED strip. If this product should become
defective, manufacturer will replace if free of charge provided it is sent with proof of purchase (copy of original receipt),
prepaid freight to PPA International, Incorporated. Warranty is in lieu of all other warranties expressed or implied,
including the warranties of merchantability of fitness for a particular purpose, whether arising by law, custom of conduct.
The rights and remedies provided under warranty are exclusive and in lieu of any other rights or remedies. In no event shall
PPA International, Incorporated be liable for consequential damages.
*Warning: Choking Hazard—small parts. Not intended for use by childern under 3 years of age.*
**Disclaimer : PPA assumes no responsibility for improper installation of the LED lights, including battery
drain, short, property damage, bodily injury, or consequential damage.**
OLSMSRGB Manual Revision 1.0-121031
O L S™
Omni Lighting Systems™
Motor Series Mult-Color Lighting Kit
User’s Manual
Model:
OLSMSRGB
Item #: 9796
4 1

2 3
oConnect fused cable wires to 12V DC adapter (red to red / black to black). Crimp
metal clamps to secure bare wiring and use electrical tape to shield metal connections
oConnect fused cable positive wire (red) to auto battery post (positive). Connect fused
cable negative wire (black) to auto battery post (negative), or any bare metal to act as
a ground. Alternate powering options may include: ignition switch wiring, or other
similar solutions where a “hot” and “ground” are available
*Professional Installation is Strongly Recommended *
INSTALLATION AND SAFETY INSTRUCTIONS
•Read all instructions carefully before installation
•Do not discard instructions
•Professional installation is strongly recommended
•Install only as instructed. Careful installation will ensure prolonged life. Repeated installations
may shorten the life of this product
•Do not excessively bend or fold strips
•Do not exceed 36 feet per controller
•Do not look directly into light
•Risk of Fire: Do not install near areas of extreme heat
•Risk of Electrical Shock:
•Do not install strips near moisture-prone areas
•Keep adapter and controller away from moisture-prone areas
Kit Contents:
•Two 1ft. multi-color LED strip
•One 1ft. extension cable
•One 2ft. extension cable
•One 10ft. fused cable
•One Y cable
•One 4in. velcro strip
•One 12V DC Adapter (cigarette lighter adapter)
•One controller
•One infrared remote
•One user’s manual
Installation:
Step 1
•Choose an area where you would like to add LED lights. Infrared remote will ONLY work in
line-of-sight to the eye of the PPA controller. Verify line-of-sight from remote to controller
Step 2
•Prior to installation, ensure area where light strips and controller are placed, is clean
Step 3
•If connecting multiple strips, taping strips to pin connections (standard electrical tape) is
recommended to ensure strips remain secure during general motion created by the road
Step 4
•If using 4in. velcro strip, cut into four identical sections to secure strips to chosen area, placing
one piece at either end of each strip (two total per strip). If sag occurs mid-strip, length of velcro
should allow for cutting into six identical sections to add velcro support at middle of strip.
Step 5
•Connect controller to LED strip (as pictured below)
Step 6 — Power Option A
•Using 12V DC adapter
oPlug 12V DC adapter into cigarette lighter power source
oConnect fused cable round plug to controller
Step 6 — Power Option B
•Using fused cable
oConnect fused cable round plug to controller
Troubleshooting
•Ensure plastic battery protector has been removed from remote
•Ensure LED strip(s) is properly connected to controller
•Ensure chosen D/C adapter is properly connected to power source
•If using multiple strips and one strip is not working, enrure non-working strip has not become
disconnected from pin connector