Olympia Lighting Fixtures Industries Akarina 14 User manual
The following symbols indicate the instructions which should be followed.
• The recommended operating temperature is between 15°C and 30°C.
• Growth varies according to conditions. Green moss grows depending on conditions. This
does not have an adverse effect. If you want to remove it, remove the plants from the
culture tray and wash the irrigation tray with washing-up liquid.
• The rooting sponges may go yellow in sunlight but this does not impair their function.
Care and storage
Switch off the appliance and remove the power cable. Now carefully remove the irrigation
tray and the culture tray without spilling the contents.
• The remaining liquid can be disposed of via the normal waste pipe or can be used to water
other plants.
• Rinse off the irrigation tray, culture tray and cover, using washing-up liquid for heavy
soiling if necessary. Rinse and dry everything thoroughly to prevent rust and corrosion
during storage.
Symptom
• If the problem persists switch the appliance off and consult your dealer.
• For questions concerning operation, care and repair first contact the dealer from whom
you bought the appliance.
Safety instructions
Attention
Warning
Read the safety instructions before using the appliance and use it properly.
The important instructions are included here in order to prevent danger and injury
to the user.
This takes the form of a step-by-step guide to dangers and injuries resulting from
improper use.
Statement on danger to life and
serious injury.
• Your appliance has a limited life span. Interior components may be damaged without this being obvious
from the outside. Regular maintenance and care are recommended for this reason. Long-term use without
maintenance / care can cause electric shock/fire.
• Disconnect the appliance from the power supply for maintenance as otherwise there is a risk of electric
shock.
• Use in a wet environment: Do not use in a damp or humid atmosphere such as a bathroom or out of doors.
This product is not waterproof.
• Do not place appliances next to each other as this increases humidity. This can result in a shorter life for the
appliance or cause fire.
• Do not combine with a dimmer switch. This causes fire.
• Do not lean against the appliance or knock into it. This causes electric damage.
• Do not look directly into the LED. This causes pain in the eyes.
LED is not switched on.
Dimensions L 210 mm x B 100 mm x H 274 mm
Input voltage AC 100-240 V 50/60 Hz
Output voltage DC 12 V 2 A
Power consumption 6 W
Weight 0.6 kg “filled approx. 0.7 kg”
Material used for main unit plastic
Length of power cable 1.5 m
Statement on possibility of injury and
damage to property.
Indicates that this should not be
carried out.
Indicates that this should be carried
out.
• Avoid damage to power cable and plug.
Damaged parts cause electric shock, short circuit and fire.
• Using with wet hands; do not touch the plug with wet hands.
This causes electric shock.
• Remove dust regularly from the power cable. Dust combined with humidity causes damage to insulation
and fire.
• Insert the plug correctly. Incomplete contact causes electric shock or heat-induced fire.
• Do not use damaged or loose plugs.
• Do not place fabric or paper or other flammable materials over the appliance or use them to cover it. This
causes fire.
• Do not carry out any modifications or changes yourself. This causes fire or injury from electric shock.
• Pull out the plug if you notice any irregularities. Then contact your dealer.
SolutioPossible cause
Instructions for use
Operating manual for Akarina 14
(Hydro culture planting system with integrated LED lighting)
Thank you for purchasing this Akarina product.
This operating manual includes important information for use and for
your safety. Retain this operating manual for reference in the future.
Culture tray
Irrigation tray
Base for main unit
Power supply
5x closure caps
1x guarantee card
1x operating manual
10x rooting sponges 1x AC adapter
1x power pack 1x power cable
• Please purchase the seeds and liquid fertilizer of your
choice separately (follow the instructions supplied with the
fertilizer).
Scope of delivery
Ensure that you have the correct number of accessories.
• The rooting sponges may go yellow in sunlight
but this does not impair their function.
LED
Control panel
CONTACT
Olympia Lighting Fixtures Industries, Ltd.
2-9-8, Honkomagome, Bunkyo City, Tokyo 113-0021, Japan
email: sale@olympia-jp.co.jp web: www.olympia-jp.co.jp/world
(Own brands AKARINA / MotoM)
www.motom-jp.com/en
Temporary loss of power
or sudden drop in voltage
LED goes out during
operation
Power cable is not
connected.
•
Switch the appliance off and
then on again after waiting 3
seconds.
• Switch mains in “OFF”
position. Check connection.
• Turn the appliance on.
Caps x 5
Rooting sponges x 10
Rinse the culture tray,
irrigation tray and clo-
sure caps with water.
Preparation
Insert the jack plug
into the jack socket
which is located on the
base of the main unit.
Stand the main unit
upright.
Note: Stand the main
unit on an even, stable
surface.
Connect to the mains
power supply at the
socket. Check that the
jack plug is securely
connected to the jack
socket.
The lighting setting of 100% provides the opti-
mum conditions for growing your plants. For
this reason we recommend you maintain LED
lighting at 100% whenever possible, i.e. LED not
in dimmed mode.
How to use the 16/8 hour timer
When the LED light is on the 16/8 hour timer can
be switched on by pressing the Timer On/Off
button twice. After the first press the LED light
will turn off then on the second press the LED
Light will turn on again. The unit is now in 16/8
hour timer mode.
To switch the timer mode off press the Power
On/Off switch. The LED light will switch off. Pres-
sing this button again will switch the unit back
on in ‘timer off’ mode.
To check if the timer mode is engaged, press
and hold any of the three buttons for at least
two seconds when the LED light is on. The LED
light will turn off after 2 seconds and in its pla-
ce there will be either a small green lamp or a
small red lamp illuminated in the panel where
the bright LEDs shine from. A GREEN lamp me-
ans the timer mode is ON. A RED lamp means
the timer mode is OFF. The LED light must be
ON to do this test because when the LED light
is OFF (even in timer mode) neither the green or
red lamps will illuminate.
These three simple switches make it easier to
grow plants!
On/Off switch
switch Press once to switch on the LED light or to switch off in
manual mode. About 16 hours of LED light is recommended
for creating optimum growth conditions. Plants also need
their night-time. So we recommend 8 hours of darkness.
Dimmer switch
Press the dimmer switch while the LED light is switched on to
select one of four light levels. Press the dimmer switch repe-
atedly to select light levels of 100% 50% 10% 1.5%. If the light
level is set at 1.5% and the dimmer switch is pressed again
the light level will return to 100%. Use the dimmer switch to
select the required light level for going to sleep, for instance,
or where and when the level of light needs to be reduced.
Timer switch
Press the timer switch to activate the timer. This sets the time
periods for the LED light to 16 hours ON and 8 hours OFF every
day. Press the timer switch while the LED light is on to start
the timer switch. The timer switch cycle will begin immedi-
ately. Press the timer switch while the timer switch mode is
in operation to come out of timer switch mode. (You can also
switch the timer switch off by switching off the power switch).
Press the timer switch again to start the 16/8 hourly cycle. The
16/8 hourly cycle only operates in timer switch mode. timer
switch mode switches on the LED light at 100% light level
only.
What you need
Starting up
Prepare the Akarina 14 for growing plants. What you need:
Top up the water / fertilizer if the water
level falls below the mark.
Note:
Use only tap water.
Not mineral water,
distilled water,
purified water or any
other liquid.
Please purchase the seeds
and liquid fertilizer of your
choice separately (follow
the instructions supplied
with the fertilizer).
One large container of tap wa-
ter, watering can (or PET bottle).
You need a large bowl, watering can (or a 1 litre PET
bottle) and the seeds and liquid fertilizer of your choice
(purchased separately).
Culture tray
Place the irrigation tray in the
main unit. Stand the main unit
on an even, stable surface.
Mix the water with the plant
fertilizer. (Store the remaining
mixture in a dark place for top-
ping up later). Follow the instruc-
tions for use on the purchased
fertilizer.
Pour the water / fertilizer mixture
into the irrigation tray up to the
lower edge of the triangular mark.
1 2 3
Triangular
marking.
Irrigation tray
IMPORTANT INFORMATION
Timer switch on/off button
On/Off switch
Dimmer switch
Place the culture tray on
the irrigation tray.
Insert the culture sponge
sufficiently deeply that it
does not protrude above
the edge of the culture tray.
After the seeds have been
planted, check them daily
to see whether they have
germinated.
If you have removed any in-
dividual plants, take out the
sponge place cap over emp-
ty hole.
• Each plant requires its own
ideal temperature.
• Thin out the leaves if they
are growing on top of each
other.
• If you have removed any
plants, also take out the
sponges and place a cap
over the space.
Separate the rooting spon-
ge at the perforations and
soak it in water.
Place one or two seeds in
each rooting sponge. Do
not plant the seeds too
deep.
Remove the closure caps
when the seeds have ger-
minated, and switch on the
LED lighting.
Harvest in about five weeks.
(Varies according to type).
Place the culture sponge
right side up in an indenta-
tion in the culture tray.
Cover the holes with the
closure caps and wait for
the seeds to germinate.
Remove any seeds which
have not germinated or
which are not growing well.
4
7
10 11 12
13
8 9
5 6
14
The control panel
Caps x 5
Rooting sponges x 10
Rinse the culture tray,
irrigation tray and clo-
sure caps with water.
Preparation
Insert the jack plug
into the jack socket
which is located on the
base of the main unit.
Stand the main unit
upright.
Note: Stand the main
unit on an even, stable
surface.
Connect to the mains
power supply at the
socket. Check that the
jack plug is securely
connected to the jack
socket.
The lighting setting of 100% provides the opti-
mum conditions for growing your plants. For
this reason we recommend you maintain LED
lighting at 100% whenever possible, i.e. LED not
in dimmed mode.
How to use the 16/8 hour timer
When the LED light is on the 16/8 hour timer can
be switched on by pressing the Timer On/Off
button twice. After the first press the LED light
will turn off then on the second press the LED
Light will turn on again. The unit is now in 16/8
hour timer mode.
To switch the timer mode off press the Power
On/Off switch. The LED light will switch off. Pres-
sing this button again will switch the unit back
on in ‘timer off’ mode.
To check if the timer mode is engaged, press
and hold any of the three buttons for at least
two seconds when the LED light is on. The LED
light will turn off after 2 seconds and in its pla-
ce there will be either a small green lamp or a
small red lamp illuminated in the panel where
the bright LEDs shine from. A GREEN lamp me-
ans the timer mode is ON. A RED lamp means
the timer mode is OFF. The LED light must be
ON to do this test because when the LED light
is OFF (even in timer mode) neither the green or
red lamps will illuminate.
These three simple switches make it easier to
grow plants!
On/Off switch
switch Press once to switch on the LED light or to switch off in
manual mode. About 16 hours of LED light is recommended
for creating optimum growth conditions. Plants also need
their night-time. So we recommend 8 hours of darkness.
Dimmer switch
Press the dimmer switch while the LED light is switched on to
select one of four light levels. Press the dimmer switch repe-
atedly to select light levels of 100% 50% 10% 1.5%. If the light
level is set at 1.5% and the dimmer switch is pressed again
the light level will return to 100%. Use the dimmer switch to
select the required light level for going to sleep, for instance,
or where and when the level of light needs to be reduced.
Timer switch
Press the timer switch to activate the timer. This sets the time
periods for the LED light to 16 hours ON and 8 hours OFF every
day. Press the timer switch while the LED light is on to start
the timer switch. The timer switch cycle will begin immedi-
ately. Press the timer switch while the timer switch mode is
in operation to come out of timer switch mode. (You can also
switch the timer switch off by switching off the power switch).
Press the timer switch again to start the 16/8 hourly cycle. The
16/8 hourly cycle only operates in timer switch mode. timer
switch mode switches on the LED light at 100% light level
only.
What you need
Starting up
Prepare the Akarina 14 for growing plants. What you need:
Top up the water / fertilizer if the water
level falls below the mark.
Note:
Use only tap water.
Not mineral water,
distilled water,
purified water or any
other liquid.
Please purchase the seeds
and liquid fertilizer of your
choice separately (follow
the instructions supplied
with the fertilizer).
One large container of tap wa-
ter, watering can (or PET bottle).
You need a large bowl, watering can (or a 1 litre PET
bottle) and the seeds and liquid fertilizer of your choice
(purchased separately).
Culture tray
Place the irrigation tray in the
main unit. Stand the main unit
on an even, stable surface.
Mix the water with the plant
fertilizer. (Store the remaining
mixture in a dark place for top-
ping up later). Follow the instruc-
tions for use on the purchased
fertilizer.
Pour the water / fertilizer mixture
into the irrigation tray up to the
lower edge of the triangular mark.
1 2 3
Triangular
marking.
Irrigation tray
IMPORTANT INFORMATION
Timer switch on/off button
On/Off switch
Dimmer switch
Place the culture tray on
the irrigation tray.
Insert the culture sponge
sufficiently deeply that it
does not protrude above
the edge of the culture tray.
After the seeds have been
planted, check them daily
to see whether they have
germinated.
If you have removed any in-
dividual plants, take out the
sponge place cap over emp-
ty hole.
• Each plant requires its own
ideal temperature.
• Thin out the leaves if they
are growing on top of each
other.
• If you have removed any
plants, also take out the
sponges and place a cap
over the space.
Separate the rooting spon-
ge at the perforations and
soak it in water.
Place one or two seeds in
each rooting sponge. Do
not plant the seeds too
deep.
Remove the closure caps
when the seeds have ger-
minated, and switch on the
LED lighting.
Harvest in about five weeks.
(Varies according to type).
Place the culture sponge
right side up in an indenta-
tion in the culture tray.
Cover the holes with the
closure caps and wait for
the seeds to germinate.
Remove any seeds which
have not germinated or
which are not growing well.
4
7
10 11 12
13
8 9
5 6
14
The control panel
Caps x 5
Rooting sponges x 10
Rinse the culture tray,
irrigation tray and clo-
sure caps with water.
Preparation
Insert the jack plug
into the jack socket
which is located on the
base of the main unit.
Stand the main unit
upright.
Note: Stand the main
unit on an even, stable
surface.
Connect to the mains
power supply at the
socket. Check that the
jack plug is securely
connected to the jack
socket.
The lighting setting of 100% provides the opti-
mum conditions for growing your plants. For
this reason we recommend you maintain LED
lighting at 100% whenever possible, i.e. LED not
in dimmed mode.
How to use the 16/8 hour timer
When the LED light is on the 16/8 hour timer can
be switched on by pressing the Timer On/Off
button twice. After the first press the LED light
will turn off then on the second press the LED
Light will turn on again. The unit is now in 16/8
hour timer mode.
To switch the timer mode off press the Power
On/Off switch. The LED light will switch off. Pres-
sing this button again will switch the unit back
on in ‘timer off’ mode.
To check if the timer mode is engaged, press
and hold any of the three buttons for at least
two seconds when the LED light is on. The LED
light will turn off after 2 seconds and in its pla-
ce there will be either a small green lamp or a
small red lamp illuminated in the panel where
the bright LEDs shine from. A GREEN lamp me-
ans the timer mode is ON. A RED lamp means
the timer mode is OFF. The LED light must be
ON to do this test because when the LED light
is OFF (even in timer mode) neither the green or
red lamps will illuminate.
These three simple switches make it easier to
grow plants!
On/Off switch
switch Press once to switch on the LED light or to switch off in
manual mode. About 16 hours of LED light is recommended
for creating optimum growth conditions. Plants also need
their night-time. So we recommend 8 hours of darkness.
Dimmer switch
Press the dimmer switch while the LED light is switched on to
select one of four light levels. Press the dimmer switch repe-
atedly to select light levels of 100% 50% 10% 1.5%. If the light
level is set at 1.5% and the dimmer switch is pressed again
the light level will return to 100%. Use the dimmer switch to
select the required light level for going to sleep, for instance,
or where and when the level of light needs to be reduced.
Timer switch
Press the timer switch to activate the timer. This sets the time
periods for the LED light to 16 hours ON and 8 hours OFF every
day. Press the timer switch while the LED light is on to start
the timer switch. The timer switch cycle will begin immedi-
ately. Press the timer switch while the timer switch mode is
in operation to come out of timer switch mode. (You can also
switch the timer switch off by switching off the power switch).
Press the timer switch again to start the 16/8 hourly cycle. The
16/8 hourly cycle only operates in timer switch mode. timer
switch mode switches on the LED light at 100% light level
only.
What you need
Starting up
Prepare the Akarina 14 for growing plants. What you need:
Top up the water / fertilizer if the water
level falls below the mark.
Note:
Use only tap water.
Not mineral water,
distilled water,
purified water or any
other liquid.
Please purchase the seeds
and liquid fertilizer of your
choice separately (follow
the instructions supplied
with the fertilizer).
One large container of tap wa-
ter, watering can (or PET bottle).
You need a large bowl, watering can (or a 1 litre PET
bottle) and the seeds and liquid fertilizer of your choice
(purchased separately).
Culture tray
Place the irrigation tray in the
main unit. Stand the main unit
on an even, stable surface.
Mix the water with the plant
fertilizer. (Store the remaining
mixture in a dark place for top-
ping up later). Follow the instruc-
tions for use on the purchased
fertilizer.
Pour the water / fertilizer mixture
into the irrigation tray up to the
lower edge of the triangular mark.
1 2 3
Triangular
marking.
Irrigation tray
IMPORTANT INFORMATION
Timer switch on/off button
On/Off switch
Dimmer switch
Place the culture tray on
the irrigation tray.
Insert the culture sponge
sufficiently deeply that it
does not protrude above
the edge of the culture tray.
After the seeds have been
planted, check them daily
to see whether they have
germinated.
If you have removed any in-
dividual plants, take out the
sponge place cap over emp-
ty hole.
• Each plant requires its own
ideal temperature.
• Thin out the leaves if they
are growing on top of each
other.
• If you have removed any
plants, also take out the
sponges and place a cap
over the space.
Separate the rooting spon-
ge at the perforations and
soak it in water.
Place one or two seeds in
each rooting sponge. Do
not plant the seeds too
deep.
Remove the closure caps
when the seeds have ger-
minated, and switch on the
LED lighting.
Harvest in about five weeks.
(Varies according to type).
Place the culture sponge
right side up in an indenta-
tion in the culture tray.
Cover the holes with the
closure caps and wait for
the seeds to germinate.
Remove any seeds which
have not germinated or
which are not growing well.
4
7
10 11 12
13
8 9
5 6
14
The control panel
The following symbols indicate the instructions which should be followed.
• The recommended operating temperature is between 15°C and 30°C.
• Growth varies according to conditions. Green moss grows depending on conditions. This
does not have an adverse effect. If you want to remove it, remove the plants from the
culture tray and wash the irrigation tray with washing-up liquid.
• The rooting sponges may go yellow in sunlight but this does not impair their function.
Care and storage
Switch off the appliance and remove the power cable. Now carefully remove the irrigation
tray and the culture tray without spilling the contents.
• The remaining liquid can be disposed of via the normal waste pipe or can be used to water
other plants.
• Rinse off the irrigation tray, culture tray and cover, using washing-up liquid for heavy
soiling if necessary. Rinse and dry everything thoroughly to prevent rust and corrosion
during storage.
Symptom
• If the problem persists switch the appliance off and consult your dealer.
• For questions concerning operation, care and repair first contact the dealer from whom
you bought the appliance.
Safety instructions
Attention
Warning
Read the safety instructions before using the appliance and use it properly.
The important instructions are included here in order to prevent danger and injury
to the user.
This takes the form of a step-by-step guide to dangers and injuries resulting from
improper use.
Statement on danger to life and
serious injury.
• Your appliance has a limited life span. Interior components may be damaged without this being obvious
from the outside. Regular maintenance and care are recommended for this reason. Long-term use without
maintenance / care can cause electric shock/fire.
• Disconnect the appliance from the power supply for maintenance as otherwise there is a risk of electric
shock.
• Use in a wet environment: Do not use in a damp or humid atmosphere such as a bathroom or out of doors.
This product is not waterproof.
• Do not place appliances next to each other as this increases humidity. This can result in a shorter life for the
appliance or cause fire.
• Do not combine with a dimmer switch. This causes fire.
• Do not lean against the appliance or knock into it. This causes electric damage.
• Do not look directly into the LED. This causes pain in the eyes.
LED is not switched on.
Dimensions L 210 mm x B 100 mm x H 274 mm
Input voltage AC 100-240 V 50/60 Hz
Output voltage DC 12 V 2 A
Power consumption 6 W
Weight 0.6 kg “filled approx. 0.7 kg”
Material used for main unit plastic
Length of power cable 1.5 m
Statement on possibility of injury and
damage to property.
Indicates that this should not be
carried out.
Indicates that this should be carried
out.
• Avoid damage to power cable and plug.
Damaged parts cause electric shock, short circuit and fire.
• Using with wet hands; do not touch the plug with wet hands.
This causes electric shock.
• Remove dust regularly from the power cable. Dust combined with humidity causes damage to insulation
and fire.
• Insert the plug correctly. Incomplete contact causes electric shock or heat-induced fire.
• Do not use damaged or loose plugs.
• Do not place fabric or paper or other flammable materials over the appliance or use them to cover it. This
causes fire.
• Do not carry out any modifications or changes yourself. This causes fire or injury from electric shock.
• Pull out the plug if you notice any irregularities. Then contact your dealer.
SolutioPossible cause
Instructions for use
Operating manual for Akarina 14
(Hydro culture planting system with integrated LED lighting)
Thank you for purchasing this Akarina product.
This operating manual includes important information for use and for
your safety. Retain this operating manual for reference in the future.
Culture tray
Irrigation tray
Base for main unit
Power supply
5x closure caps
1x guarantee card
1x operating manual
10x rooting sponges 1x AC adapter
1x power pack 1x power cable
• Please purchase the seeds and liquid fertilizer of your
choice separately (follow the instructions supplied with the
fertilizer).
Scope of delivery
Ensure that you have the correct number of accessories.
• The rooting sponges may go yellow in sunlight
but this does not impair their function.
LED
Control panel
CONTACT
Olympia Lighting Fixtures Industries, Ltd.
2-9-8, Honkomagome, Bunkyo City, Tokyo 113-0021, Japan
email: sale@olympia-jp.co.jp web: www.olympia-jp.co.jp/world
(Own brands AKARINA / MotoM)
www.motom-jp.com/en
Temporary loss of power
or sudden drop in voltage
LED goes out during
operation
Power cable is not
connected.
•
Switch the appliance off and
then on again after waiting 3
seconds.
• Switch mains in “OFF”
position. Check connection.
• Turn the appliance on.
The following symbols indicate the instructions which should be followed.
• The recommended operating temperature is between 15°C and 30°C.
• Growth varies according to conditions. Green moss grows depending on conditions. This
does not have an adverse effect. If you want to remove it, remove the plants from the
culture tray and wash the irrigation tray with washing-up liquid.
• The rooting sponges may go yellow in sunlight but this does not impair their function.
Care and storage
Switch off the appliance and remove the power cable. Now carefully remove the irrigation
tray and the culture tray without spilling the contents.
• The remaining liquid can be disposed of via the normal waste pipe or can be used to water
other plants.
• Rinse off the irrigation tray, culture tray and cover, using washing-up liquid for heavy
soiling if necessary. Rinse and dry everything thoroughly to prevent rust and corrosion
during storage.
Symptom
• If the problem persists switch the appliance off and consult your dealer.
• For questions concerning operation, care and repair first contact the dealer from whom
you bought the appliance.
Safety instructions
Attention
Warning
Read the safety instructions before using the appliance and use it properly.
The important instructions are included here in order to prevent danger and injury
to the user.
This takes the form of a step-by-step guide to dangers and injuries resulting from
improper use.
Statement on danger to life and
serious injury.
• Your appliance has a limited life span. Interior components may be damaged without this being obvious
from the outside. Regular maintenance and care are recommended for this reason. Long-term use without
maintenance / care can cause electric shock/fire.
• Disconnect the appliance from the power supply for maintenance as otherwise there is a risk of electric
shock.
• Use in a wet environment: Do not use in a damp or humid atmosphere such as a bathroom or out of doors.
This product is not waterproof.
• Do not place appliances next to each other as this increases humidity. This can result in a shorter life for the
appliance or cause fire.
• Do not combine with a dimmer switch. This causes fire.
• Do not lean against the appliance or knock into it. This causes electric damage.
• Do not look directly into the LED. This causes pain in the eyes.
LED is not switched on.
Dimensions L 210 mm x B 100 mm x H 274 mm
Input voltage AC 100-240 V 50/60 Hz
Output voltage DC 12 V 2 A
Power consumption 6 W
Weight 0.6 kg “filled approx. 0.7 kg”
Material used for main unit plastic
Length of power cable 1.5 m
Statement on possibility of injury and
damage to property.
Indicates that this should not be
carried out.
Indicates that this should be carried
out.
• Avoid damage to power cable and plug.
Damaged parts cause electric shock, short circuit and fire.
• Using with wet hands; do not touch the plug with wet hands.
This causes electric shock.
• Remove dust regularly from the power cable. Dust combined with humidity causes damage to insulation
and fire.
• Insert the plug correctly. Incomplete contact causes electric shock or heat-induced fire.
• Do not use damaged or loose plugs.
• Do not place fabric or paper or other flammable materials over the appliance or use them to cover it. This
causes fire.
• Do not carry out any modifications or changes yourself. This causes fire or injury from electric shock.
• Pull out the plug if you notice any irregularities. Then contact your dealer.
SolutioPossible cause
Instructions for use
Operating manual for Akarina 14
(Hydro culture planting system with integrated LED lighting)
Thank you for purchasing this Akarina product.
This operating manual includes important information for use and for
your safety. Retain this operating manual for reference in the future.
Culture tray
Irrigation tray
Base for main unit
Power supply
5x closure caps
1x guarantee card
1x operating manual
10x rooting sponges 1x AC adapter
1x power pack 1x power cable
• Please purchase the seeds and liquid fertilizer of your
choice separately (follow the instructions supplied with the
fertilizer).
Scope of delivery
Ensure that you have the correct number of accessories.
• The rooting sponges may go yellow in sunlight
but this does not impair their function.
LED
Control panel
CONTACT
Olympia Lighting Fixtures Industries, Ltd.
2-9-8, Honkomagome, Bunkyo City, Tokyo 113-0021, Japan
(Own brands AKARINA / MotoM)
www.motom-jp.com/en
Temporary loss of power
or sudden drop in voltage
LED goes out during
operation
Power cable is not
connected.
•
Switch the appliance off and
then on again after waiting 3
seconds.
• Switch mains in “OFF”
position. Check connection.
• Turn the appliance on.
Table of contents
