3 Shooting/Playback
Taking still pictures
1
11
1
Open the lens barrier.
Slide the lens barrier open until it clicks.
The flash pops up and the lens extends.
2
22
2
Position the AF target mark over the
subject in the viewfinder.
3
33
3
Press the shutter button gently (halfway).
The green lamp on the right of the viewfinder
lights up when the focus and exposure are
locked. At this time the sound of the focusing
mechanism can be heard from inside the
camera, but no picture is being taken.
4
44
4
Press the shutter button all the way (fully).
The camera takes the picture.
Playing back still pictures
1
11
1
Press with the lens barrier closed.
The monitor turns on and displays the last picture taken.
2
22
2
Press to display the previous/next picture.
3
33
3
Press to cancel playback.
The monitor and camera
turn off.
Recording movies
1
11
1
Press with the lens barrier open.
The top menu in the shooting mode is displayed.
2
22
2
Press to select DRIVE.
3
33
3
Press to select , then press
.
4
44
4
Record the movie while observing your
subject on the monitor.
Press the shutter button fully to start recording.
Press the shutter button fully again to stop
recording.
Playing back movies
1
11
1
Press with the lens barrier closed.
The monitor turns on.
2
22
2
Press to display the desired picture with a indicator, then
press .
The top menu is displayed.
3
33
3
Press to select MOVIE PLAYBACK.
The movie is played back after the orange lamp on the right of the viewfinder
blinks and the movie data is downloaded to the camera. When the movie
reaches the end, the display returns automatically to the beginning of the movie.
4
44
4
Press to display the MOVIE
PLAYBACK menu. Then select the
desired operation and press .
PLAYBACK: Plays back the entire
movie again.
FRAME BY FRAME: Plays back the movie
manually one frame at a
time.
EXIT: Leaves the movie playback mode.
4 Erasing pictures
Single-frame erase
1
11
1
Press with the lens barrier closed.
The monitor turns on.
2
22
2
Press to select the picture you want to erase.
3
33
3
Press .
The top menu is displayed.
4
44
4
Press to select ERASE.
5
55
5
Press to select YES, then
press .
The picture is erased and the menu is closed.
5 Protecting pictures (Protect)
You are recommended to protect important pictures to avoid accidentally erasing
them.
1
11
1
Press with the lens barrier closed.
The monitor turns on.
2
22
2
Press to select the picture you want to protect.
3
33
3
Press , then press .
The mode menu is displayed.
4
44
4
Press to select the PLAY tab, then press .
5
55
5
Press to select , then
press .
6
66
6
Press to select ON.
The selected picture is protected.
To close the menu, press twice.
AF target mark
Orange lamp
Green
lamp
Jumps to the picture 10 frames behind.
Displays the
next picture.
Jumps to the picture 10 frames ahead.
Displays the
previous picture.
DRIVE
CANCEL
GO
SELECt
FRAME BY FRAME
EXIt
MOVIE PLAYBACK
PLAYBACK
SELECt
GO
• Erasure is not possible if the picture you want to erase is protected or a
write-protect seal is attached to the card. Before erasing, unprotect the
picture or remove the write-protect seal from the card.
• Once erased, pictures cannot be restored. Check each picture before
erasing to avoid accidentally erasing pictures you want to keep.
MODE MENU
INFO
ERASE
YES
NO
SELECt
GO
ERASE
• The indicator is displayed at the top right of the protected picture.
• Protection on each picture remains even when the camera is turned off.
• Protected pictures cannot be erased by the single-frame/all-frame erase
function, but they can be all erased with the format function.
• Protection cannot be applied to pictures stored on a card with a write-
protect seal.
CARDSEt EDIt
PLAY
CARDSEt EDIt
PLAY
OFF
ON
We’ve included this convenient Quick start guide to show you basic functions and
techniques that will help you quickly master your new camera. For more detailed
descriptions of procedures, as well as for additional information on more sophisticated
features not covered here, please refer to the printed “Basic Manual”, or the primary
“Reference Manual” on the CD-ROM.
Package contents
1 Getting started
Attaching the strap
1
11
1
Thread the short end of the strap through the
strap eyelet.
2
22
2
Thread the long end of the strap through the
loop that has already gone through the
eyelet.
3
33
3
Pull the strap tight, making sure that it is
securely fastened and does not come loose.
Loading the batteries
1
11
1
Make sure that:
2
22
2
Slide the battery compartment
cover in the direction of (the
direction indicated by the
mark on the cover), and lift it up in
the direction of .
3
33
3
Insert the batteries, making sure
that they are correctly oriented as
shown in the illustration.
4
44
4
Close the battery compartment cover in the
direction of . While pressing the mark,
slide the cover in the direction of .
If the battery compartment cover will not close easily, do
not force it. Try pressing the mark with both hands.
Inserting the card (SmartMedia)
1
11
1
Make sure that:
2
22
2
Open the card cover.
3
33
3
Insert the card as far as it will go in the
direction shown in the illustration.
There is an arrow inside the card cover, indicating
the direction in which the card should be inserted.
4
44
4
Close the card cover securely until it clicks
Removing the card.
Hold the card with your fingertips and pull it out in the
direction of the arrow.
2 Turning the power on/off
When shooting pictures
When playing back pictures
C-2 Zoom
C-2 ZoomC-2 Zoom
C-2 Zoom
D-520 ZOOM
D-520 ZOOMD-520 ZOOM
D-520 ZOOM
C-220 ZOOM
C-220 ZOOMC-220 ZOOM
C-220 ZOOM
Quick start guide
DIGITAL CAMERA
Camera
Strap
AA (R6) alkaline batteries (2 pieces)
Video cable
USB cable
Basic manual
;Quick start guide
Software installation guide (included in
the CD-ROM package)
CD-ROM with Windows 98 USB driver
software, Reference manual, and more.
Warranty card/Registration card (not
provided in some areas)
Safety Precautions (booklet)
SmartMedia
Static-free case
Index labels (2 pieces)
Write-protect adhesive seals (4 pieces)
SmartMedia instructions
Printed in Japan
VT351301
OLYMPUS AMERICA INC.
Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A. Tel. 631-844-5000
24/7 online automated help: http://support.olympusamerica.com/
Phone customer support: Tel. 1-888-553-4448 (Toll-free)
OLYMPUS OPTICAL CO. (EUROPA) GMBH.
Premises/Goods delivery: Wendenstraße 14-18, 20097 Hamburg, Germany
Tel. 040-237730
Letters: Postfach 10 49 08, 20034 Hamburg, Germany
http://www.olympus.com/
The lens barrier
is closed.
The lamp on the right
of the viewfinder is off.
The monitor
is off.
Battery
insertion
direction
mark
When using a
lithium battery
pack
When using AA
(R6) batteries
Never open the card cover, or remove the card or the batteries while the
camera is turned on. Doing so could destroy all data on the card. Destroyed
data cannot be restored.
The lens barrier
is closed.
The lamp on the right of
the viewfinder is off.
The monitor is off.
Card insertion
direction mark
To save battery power, the camera automatically enters the sleep mode
after about 3 minutes of non-operation. If the monitor is on, it will
automatically turn off. The camera activates again as soon as you lightly
press the shutter button or zoom lever. Whenever possible, turn the camera
off when you do not intend to take any pictures for a while.
Power on Power off
Power on:
Open the lens barrier.
The camera turns on in the
shooting mode. The lens
extends and the flash pops up.
If the lens does not extend, the
lens barrier is not fully open.
Open the lens barrier until it
clicks.
Power off:
Close the lens barrier slightly
until it just touches the lens
barrier.
Wait until the lens is fully
retracted, then close the lens
barrier completely.
The camera turns off. (The
monitor also turns off.)
Press the flash down manually
until it locks in place.
Power ON Power OFF
Power on:
Press the (monitor) button
with the lens barrier closed.
The camera turns on in the
playback mode. The monitor
turns on.
Power off:
Press the (monitor)
button.
The camera turns off (the
monitor turns off).
With the lens
barrier closed
qsge_dquick.fm Page 1 Friday, February 8, 2002 12:25 PM
