Olympus CAMEDIA C-5060 Wide Zoom Installation guide

DIGITAL CAMERA
APPAREIL PHOTO NUM ÉRIQUE
DIGITALKAMERA
CÁMARA DIGITAL
C-5060 Wide Zoom
BASIC MANUAL
MANUEL DE BASE
EINFACHE ANLEITUNG
MANUAL BÁSICO
ENGLISH..........2
FRANÇAIS .....52
DEUTSCH ....102
ESPAÑOL ....152
basic_e_x191_6.fm Page 1 Thursday, August 28, 2003 12:44 PM

2En
En
GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
MENU FUNCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
MODE DIAL AND DIRECT BUTTON FUNCTIONS . . . .26
SHOOTING BASICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Taking still pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
If correct focus cannot be obtained (Focus lock) . . . . 33
Recording movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Zooming in on a subject (optical zoom) . . . . . . . . . . . 35
Using the flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Using the self-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
ADVANCED SHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . 37
PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Viewing still pictures . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Viewing movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Protecting pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Erasing pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Formatting (CARD SETUP). . . . . . . . . . . . . . . . . . . . . 42
Playback on a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
PRINT RESERVATION/DIRECT PRINT . . . . . . . . . . . . . 44
DOWNLOADING PICTURES TO A COMPUTER . . . . . .45
ERROR CODES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
CONTENTS
These instructions are only for quick reference. For more details
on the functions described here, refer to the “Reference Manual”
on CD-ROM.
basic_e_x191_6.fm Page 2 Thursday, August 28, 2003 12:44 PM

En 3
En
JBefore using your camera, read this manual carefully to ensure correct use.
JWe recommend that you take test shots to get accustomed to your camera before
taking important photographs.
JThese instructions are only a basic manual. For more details on the functions described
here, refer to the Reference Manual on the CD-ROM. For connection to the PC or
installation of provided software, refer to the Software Installation Guide included in the
CD-ROM package.
For customers in North and South America
For customers in Europe
Trademarks
• IBM is a registered trademark of International Business Machines Corporation.
• Microsoft and Windows are registered trademarks of Microsoft Corporation.
• Macintosh is a trademark of Apple Computer Inc.
• All other company and product names are registered trademarks and/or
trademarks of their respective owners.
• The standards for camera file systems referred to in this manual are the “Design
Rule for Camera File System/DCF” standards stipulated by the Japan Electronics
and Information Technology Industries Association (JEITA).
“CE” mark indicates that this product complies with the European
requirements for safety, health, environment and customer
protection. “CE” mark cameras are intended for sales in Europe.
For customers in USA
Declaration of Conformity
Model Number : C-5060 Wide Zoom
RM-2 (Romote control)
Trade Name : OLYMPUS
Responsible Party : Olympus America Inc.
Address : 2 Corporate Center Drive, Melville, New York
11747-3157 U.S.A.
Telephone Number : 631-844-5000
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
For customers in Canada
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
basic_e_x191_6.fm Page 3 Thursday, August 28, 2003 12:44 PM

4En
En
GETTING STARTED
JNAMES OF PARTS
Lens
A specified filter can be
attached (optional).
Remote control receiver
Strap eyelet
AF illuminator
Self-timer/Remote control lamp
Microphone
DC-IN jack
Flash
A/V OUT jack (MONO)
USB connector
Connector cover
AF sensor
Speaker
Viewfinder window
basic_e_x191_6.fm Page 4 Thursday, August 28, 2003 12:44 PM

En 5
En
Viewfinder
Green lamp
AF target mark
Orange lamp
AEL button (AEL)
Erase button (S)
Power switch
Control dial
Monitor button (f)
Card cover
Card access lamp
Arrow pad (acbd)
OK/Menu button
( e )
Card button (CF/xD)
Monitor
QUICK VIEW button
Flash mode button (#)
Exposure compensation button (F)
Diopter adjustment dial
basic_e_x191_6.fm Page 5 Thursday, August 28, 2003 12:44 PM

6En
En
Metering button (4)
Protect button (0)
AF/Macro/MF button (AF/&/MF)
Mode dial
Self-timer/Remote control button
(Z)
Rotation button (y)
Zoom lever (T/W·UG)
Shutter button
Custom button (z)
Print button (<)
Control panel
Hot shoe
Battery compartment cover
Battery compartment lock
Tripod socket
basic_e_x191_6.fm Page 6 Thursday, August 28, 2003 12:44 PM

En 7
En
JCONTROL PANEL INDICATIONS
Item Indications
1 Battery check ,
2 Shutter speed
Program shift
2ooo (1/2000 sec.), 2.5"
S is displayed in the program shift mode.
3 Aperture value F2.8 to F8.0
4 Exposure compensation
Flash intensity control
+2.0, +1.0, 0.0, -1.0, -2.0
5 Accessory 1
6 Macro mode
Super macro mode
&(Lights)
&(Blinks)
7 Manual focus
Super macro MF mode
MF (Lights)
MF (Blinks)
8 Self-timer Y
9 Remote control
10 Sound record R
11 Sequential shooting mode h, j, l, 7
12 Flash intensity control w
<
basic_e_x191_6.fm Page 7 Thursday, August 28, 2003 12:44 PM

8En
En
Item Indications
13 Record mode RAW, TIFF, SHQ, HQ, SQ
14 Noise reduction NR
15 AE lock
AE memory
AEL
AELE
16 Metering mode 3, 2, MULTI3
17 ISO ISO
18 White balance WB
19 Flash mode !, #, $, #SLOW, HSLOW
20 Card ,
21 Number of storable still
pictures/Seconds
remaining
Error code
30
-E-
basic_e_x191_6.fm Page 8 Thursday, August 28, 2003 12:44 PM

En 9
En
JMONITOR INDICATIONS
Shooting mode
Turn the power on and the monitor turns on displaying the shooting
information. Each time you press f, the information display changes.
Item Indications
1 Shooting mode P, A, S, M, s, N, m, L, K, J, I
2 Shutter speed 15" to 1/4000
3 Aperture value F2.8 to F8.0
4 Exposure compensation
Exposure differential
-2.0 to +2.0
-3.0 to +3.0
5 Battery check e, f
6 Green lamp
7 Flash stand-by
Camera movement
warning/
Flash charge
#Lights
#Blinks
8 Macro mode
Super macro mode
Manual focus
&
%
MF
9 Noise reduction O
10 Flash mode !, #, $, #SLOW1, HSLOW1, #SLOW2
Still picture Movie
basic_e_x191_6.fm Page 9 Thursday, August 28, 2003 12:44 PM

10 En
En
11 Flash intensity control w-2.0 to +2.0
12 Drive o, i, j, k, 7
13 Self-timer
Remote control
Y
<
14 Sound record R
15 Record mode RAW, TIFF, SHQ, HQ, SQ1, SQ2
16 Resolution 2592×1944, 1600×1200, 640×480, 320×240 etc.
17 AF target mark
Metering target mark
[]
18 Number of storable still
pictures
Seconds remaining
30
36"
19 AE lock
AE memory
B
C
20 Metering mode 5, 4
21 ISO ISO 80, ISO 100, ISO 200, ISO 400
22 White balance 2, 3, 5, 4, w- z, 1, C1to C4, V
23 White balance adjustment B1 to B7, R1 to R7
24 Saturation 6-5 to +5
25 Sharpness N-5 to +5
26 Contrast J-5 to +5
27 Scene modes i, l, m
28 Memory gauge a, b, c, d
29 Card [xD], [CF]
Item Indications
basic_e_x191_6.fm Page 10 Thursday, August 28, 2003 12:44 PM

En 11
En
Playback mode
Screens with the information display set to ON are shown below.
Item Indications
1 Battery check e, f
2 Card [xD], [CF]
3 Print reservation,
Number of prints
Movie
<×10
n
4 Sound record H
5Protect 9
6 Record mode RAW, TIFF, SHQ, HQ, SQ1, SQ2
7 Resolution 2592×1944, 1600×1200, 640×480, 320×240 etc.
8 Aperture value F2.8 to F8.0
9 Shutter speed 15" to 1/4000
10 Exposure
compensation
-2.0 to +2.0
11 White balance WB AUTO, 2, 3, 5, 4, wto z, 1, V
12 ISO ISO 80, ISO 100, ISO 200, ISO 400
13 Date and time ’03.12.17 15:30
14 File number
Playing time/Total
recording time
FILE : 100 - 0030
0"/20"
Still picture Movie
basic_e_x191_6.fm Page 11 Thursday, August 28, 2003 12:44 PM

12 En
En
Memory gauge
The memory gauge lights up when you take a still picture. While the gauge is
lit, the camera is storing the picture on the card. The memory gauge
indication changes as shown below depending on the shooting status. The
indication is not displayed during movie recording.
Battery check
If the remaining battery power is low, the battery check indication on the
control panel and monitor changes as follows when the camera is turned on
or while the camera is in use.
Battery check Control panel Monitor Status
eLights Lights (green)
(Goes off after a while)
Remaining power level: high
fBlinks Blinks (red) Remaining power level: low
If you intend to use the
camera for a long period of
time, charge the battery as
soon as possible.
No indication
The green lamp and orange lamp at the
side of the viewfinder blink. (The control
panel turns off automatically.)
Remaining power level:
exhausted
Charge the battery.
adcb
Before shooting
(Gauge is off)
No more pictures
can be taken
(Fully lit)
Wait until the gauge
returns to the status
on the left to take the
next shot.
One picture
taken
(Lit)
More than
two taken
(Lit)
Shoot Shoot Shoot
Wait
basic_e_x191_6.fm Page 12 Thursday, August 28, 2003 12:44 PM

En 13
En
JATTACHING THE STRAP AND LENS CAP
JCHARGING THE BATTERY
This camera uses one BLM-1 lithium ion battery. Other batteries cannot be used.
The battery is not fully charged at the time of purchase. Before using the
camera, charge the battery using the BCM-2 charger. For more details, read
the instructions provided with the charger.
1Plug the power cord into the
charger and plug the other end
of the power cord into a
household electrical outlet.
2Remove the protection cap
from the battery.
3Place the battery on the
charger, making sure that it is correctly oriented as shown
in the illustration.
• Align the battery with the guideline on
the charger ( ), and insert the
battery into the charger as far as it will
go.
• Meaning of the charge lamp
indications:
Lights red : Charging
Lights green : Charging is completed.
Blinks red : Charging failure
• The battery charges in approximately 6 hours. The charging time may
differ according to the amount of power left in the battery.
1
345
2
Charge indicator
basic_e_x191_6.fm Page 13 Thursday, August 28, 2003 12:44 PM

14 En
En
JLOADING THE BATTERY
1Make sure the power switch is set to OFF.
2Slide the battery compartment
lock from =to )and open the
battery compartment cover.
3Insert the battery, making sure
that it is correctly oriented as
shown in the illustration.
• The lock secures the battery when
correctly loaded.
4Close the battery
compartment cover.
5Slide the battery compartment
lock from )to =.
JINSERTING A CARD
“Card” in this manual refers to the xD-Picture Card, CompactFlash and
Microdrive. The camera uses the card to record pictures.
1Make sure the power switch is set to OFF.
2Open the card cover.
3Insert a card.
xD-Picture Card
• Insert the card into the slot with the contact
area toward you. Ensure the card is not
inserted diagonally.
• Insert the card as far as it will go until it
clicks.
• If the card is inserted incorrectly oriented or
it is inserted at an angle, the contact area
may be damaged or the card may become jammed.
• If the card is not inserted fully, it may not be able to record data.
Battery lock
Contact area
Notch
Card cover
basic_e_x191_6.fm Page 14 Thursday, August 28, 2003 12:44 PM

En 15
En
CompactFlash/Microdrive
• Hold the card straight and insert it correctly into
the front slot, as shown.
4Close the card cover securely until it
clicks.
Removing the card
xD-Picture Card
• Push the card all the way in to unlock it, then let it return slowly. The card
is ejected a short way and then stops. Hold the card straight and pull it out.
CompactFlash/Microdrive
• Press the eject button gently and allow it to pop out, then press it again all
the way in. The card will be ejected a short way to enable you to pull it out.
Switching cards
The card currently in use is displayed on the control panel or monitor. Choose
the card you want to record the picture on before taking the picture.
The factory default setting is the xD-Picture Card. If only one card is inserted,
that card is automatically selected. Card selection can also be made in
Playback mode.
Releasing your finger quickly after pushing the card all the way in may
cause it to eject forcefully out of the slot.
Note
basic_e_x191_6.fm Page 15 Thursday, August 28, 2003 12:44 PM

16 En
En
JTURNING THE POWER ON/OFF
Power on
1Remove the lens cap.
2Pull the monitor out and rotate it.
• Some of the camera’s functions cannot be operated if the monitor is left
closed. Be sure to open the monitor before shooting or playing back
images.
• You can change the angle of the monitor.
3Turn the mode dial until the mode
you want to use is aligned with the
red line.
4Turn the power switch so that ON
is aligned with the (mark.
• When the mode dial is set to a mode other
than q, the camera turns on in the
shooting mode. The monitor turns on and
the lens extends.
• When the mode dial is set to q, the
camera turns on in the playback mode
and the monitor turns on.
• You can also change the mode with the
camera turned on.
Mode
dial
Power
switch
basic_e_x191_6.fm Page 16 Thursday, August 28, 2003 12:44 PM

En 17
En
Power off
1To turn the power off, turn the power switch
so that OFF is aligned with the (mark.
• The monitor turns off, the lens retracts and the power
turns off.
2Turn the monitor towards the camera and
close it.
• To protect the monitor, you are recommended to keep
it closed when the camera is not in use.
JSELECTING A LANGUAGE
1Set the mode dial to Pand turn the camera on.
• You can select the language in all modes.
2Press e.
• The top menu is displayed.
3Press don the arrow pad to select MODE MENU.
4Press ac to select the SETUP tab, then press d.
5Press ac to select W, then press d.
6Press ac to select a language, then press e.
7Press eagain to exit the menu.
8To turn the camera off, set the power switch to OFF.
JSETTING THE DATE AND TIME
1Set the mode dial to Pand turn the camera on.
• You can set the date and time in all modes.
2Press e.
• The top menu is displayed.
3Press don the arrow pad to select MODE MENU.
4Press ac to select the SETUP tab, then press d
5Press ac to select X, then press d.
• The green frame moves to the selected item.
•Presscrepeatedly to change the page until Xis displayed.
basic_e_x191_6.fm Page 17 Thursday, August 28, 2003 12:44 PM

18 En
En
6Press ac to select one of the following date formats: Y-
M-D (Year/Month/Day), M-D-Y (Month/Day/Year), D-M-Y
(Day/Month/Year). Then press d.
• Move to the year setting.
• The following steps show the procedure used when the date and time
settings are set to Y-M-D.
7Press ac to set the year, then press dto move to the
month setting.
• To move back to the previous setting, press b. The first two digits of
the year are fixed.
8Repeat this procedure until the date and time are
completely set.
• The time is displayed in the 24-hour format.
For example, 2pm will be displayed as 14:00.
9Press e.
• For a more accurate setting, press ewhen the time signal hits 00
seconds.
10 To turn the camera off, set the power switch to OFF.
• The date and time settings will be canceled if the camera is left
without the battery for approximately 5 days.
Note
basic_e_x191_6.fm Page 18 Thursday, August 28, 2003 12:44 PM

En 19
En
MENU FUNCTIONS
JUSING THE MENUS AND TABS
When you turn on the camera and press e, the top menu is displayed on the
monitor. The functions of this camera are set from the menus. This chapter
explains how the menus work, using the Pmode screens.
How to use the menus
1Press eto display the top menu. Press d.
2Press ac to select a tab, then press d.
3Press ac to select the item you want to set, then press
d.
4Press ac to select a setting. Press eto complete
setting.
Press eagain to exit the menu and return to shooting
status.
WB
DRIVE
MODE MENU
• Take you directly to the setting
screens.
• Display operational buttons at the
bottom of the screen.
• The functions registered in the
shortcut menus can also be
accessed from the MODE MENU.
• You can change the shortcut
menus in any mode other than
nq modes.
• Lets you access the menu
selections to set the ISO,
sharpness, etc.
• Categorizes the settings into
tabs.
• Displays the associated menu
items when a tab is selected by
pressing ac.
Use the arrow pad
to select a menu.
Press e.
MODE MENU
SHORTCUT MENUS
The top menu is displayed.
basic_e_x191_6.fm Page 19 Thursday, August 28, 2003 12:44 PM

20 En
En
Shortcut menus
Shooting mode
Playback mode
Selects a shooting mode from o(single-frame shooting), i(high
speed sequential shooting), j(sequential shooting), k(AF
sequential shooting) and 7(auto bracketing).
Selects whether to record sound when shooting a movie.
Sets the image quality and resolution.
Still picture : RAW, TIFF, SHQ, HQ, SQ1, SQ2
Movie : SHQ, HQ, SQ
Sets the appropriate white balance according to the light source.
Runs through all saved pictures one after another.
MOVIE PLAYBACK Plays back movies.
INDEX Creates an indexed view of a movie in 9 frames.
EDIT Edits a movie.
Displays all the shooting information on the monitor.
DRIVE
R(movies)
K
WB
m
MOVIE PLAY
INFO
basic_e_x191_6.fm Page 20 Thursday, August 28, 2003 12:44 PM