Omcan GR-CN-0914 User manual

Outdoor Propane Griddle
Model GR-CN-0914
Item 43022
Instruction Manual
Revised - 07/26/2017 Factory CSA
approved
Toll Free: 1-800-465-0234
Fax: 905-607-0234
Email: [email protected]
www.omcan.com

2
Page
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 6
-------------------------------------------------------------------------- 7
----------------------------------------------------------------------- 7 - 10
------------------------------------------------------------------------------------ 10 - 12
------------------------------------------------------------------------------------- 12 - 14
--------------------------------------------------------------------------------- 14 - 16
----------------------------------------------------------------------------- 17 - 18
---------------------------------------------------------------------------- 18 - 19
------------------------------------------------------------------------------------------- 20 - 22
---------------------------------------------------------------------------- 23
Table of Contents
Section
General Information
Safety and Warranty
Technical Specications
Assembly Instructions
Installation
Operation
Maintenance
Troubleshooting
Parts Breakdown
Notes
Warranty Registration
Model GR-CN-0914

3
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.

4
General Information
Safety and Warranty
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre leer y familiarizarse con todas las instrucciones de
operación y seguridad.
Omcan quisiera darles las gracias por la compra de esta máquina. Es de la máxima importancia para
guardar estas instrucciones para referencias en el futuro. También guarde la caja original y el embalaje
para envío del equipo si el mantenimiento o la devolución de la máquina es necesaria.
FOR YOUR SAFETY
1. Read this User Manual before attempting to assemble or operate your griddle.
2. Follow all safety instructions.
3. Check for leaks according to directions in this manual before operating your griddle, even if you purchased
this griddle fully assembled.
4. If you should require any assistance concerning the assembly or use of this machine, please contact

5
Safety and Warranty
Omcan directly.
THIS GRIDDLE IS FOR OUTDOOR USE ONLY
If stored indoors, then detach and leave propane cylinder outside.
Always read and follow all DANGER, WARNING, and FOR YOUR SAFETY notices in this manual. Failure to
follow these notices may result in property damage, bodily or physical injury, or death.
1. Griddle installation must conform with local codes, or in their absence, with either the national Fuel Gas
Code, ANSI Z223.1/NFPA 54, Nautal Gas and Propane Installation Code, CSA B149.1, or Propane Storage
and Handling Code, B149.2.
2. This gas grill is intended for outdoor use only, and should not be used in a building, garage, or any other
enclosed area.
3. This gas grill is not intended to be installed in or on recreational vegicles and/or boats.
4. Never use any other type of fuel for this grill other than LP gas (propane).
5. Only use the pressure regulator with a type 1 connector that is supplied with this gas grill,
6. Before each use, check the gas hose for excessive abrasion, cracking, fraying, wear, or cuts. Replace a
hose assembly showing those signs with the hose assembly specied in the parts list before using the grill.
7. Always perform a leak test before operating your grill.
WARNING
1. Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other
appliance.
2. An LP cylinder not connected for use should not be stored in the vicinity of this or any other appliance.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. If odor continues, keep away from appliance and call our local re department.
WARNING
1. Do not store a spare LP-gas cylinder under or near this appliance.
2. Never ll the cylinder beyond 80 percent full, this may cause release of gas from the safety release valve.
3. If the information in this manual is not followed exactly, a re causing death or serious injury may occur.
WARNING
1. Do not attempt to use a cylinder with any other type of connection device.
2. Do not attempt to use a cylinder with a larger capacity.
WARNING
A frosty cylinder valve indicates possible gas overll. Close the LP valve and call your dealer immediately.
WARNING
1. Never store any extra cylinders near your griddle.

6
Safety and Warranty
2. Keep cylinders out of direct sunlight and high heat.
3. Immediately call your LP dealer or re department should you hear, smell, or see escaping gas from the
cylinder.
4. Do not insert any type of foreign objects into the valve outlet.
WARNING
1. The gas supply must be turned off at the LP-gas supply cylinder when this outdoor cooking gas appliance
is not in use.
2. Storage of this gas griddle indoors is permissible only if the cylinder is disconnected and removed from the
gas griddle.
3. Cylinders must be stored outdoors out of reach of children and must not be stored in a building, garage, or
any other enclosed area.
1 YEAR PARTS AND LABOR WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized
service technician to repair the equipment locally.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see www.omcan.com/warranty.html for complete info.
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without difculty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

7
Assembly Instructions
STEP 1
Attach the left leg(6) and right leg(10) onto the griddle
body(12) using BOLT M6X12(A)-10PCS.
STEP 2
Attach the fence rail(9)-3PCS to legs using BOLT
M6X15(B)-12PCS.
Technical Specications
Model GR-CN-0914
Cooking Area 36” x 20” / 914 x 508mm
Number of Burners 4
Gas Type - Size Liquid Propane - 20 lbs. / 9.1 kgs.
Dimensions 66” x 24.25” x 36.25” / 1676 x 616 x 921mm
Weight 119 lbs. / 54 kg.
Item Number 43022

8
Assembly Instructions
STEP 3
Install directional casters(8) onto legs.
STEP 4
Install the gas tank hook(2) onto the griddle body
using BOLT M6X12(A)-2PCS. Then install the
gas tank holder (7) onto the bottom using BOLT
M6X60(C)-2PCS and Nut M6 Flange Lock (D)-2PCS.
STEP 5
Assemble the side handle(4)-2PCS to the each side
of the griddle body using BOLT M6X12(A)-8PCS.

9
Assembly Instructions
STEP 6
Install the side shelf (3)-2PCS onto body using PIN
ROLL(E)-4PCS and “R” PIN (F) -4PCS.
STEP 7
Put the griddle top(1) onto the body.
STEP 8
Put the oil cup (11) on the side shelf.

10
Assembly Instructions
Installation
STEP 9
Install the knob(5)-4PCS onto the body. Assemble
extension wire(13) on front side of the body using
BOLT pre-assembled on the control panel. Then
install the battery into the ignitor.
TRANSPORTATION AND STORAGE
1. Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap
on the cylinder valve outlet that is provided with the cylinder valve. Other types od caps or plugs may result
in leakage of propane.
2. Do not store in a building, garage, or other enclosed area.
3. Always store your cylinder outside.
4. Store out of reach of children.
5. Always transport in an upright position.
6. Do not smoke when transporting your cylinder.
REGULATOR AND LP CYLINDER CONNECTIONS
CAUTION
The gas pressure regulator provided with this outdoor cooking appliance must be used. This regulator is set for
an outlet pressure of 11 inches water column.
Your regulator is equipped with a Q.C.C. Type 1 quick connect system. It will not allow gas to ow until a
positive seal has been made. It has a thermal element that will shut off the gas ow if the temperature reaches
240 degrees F (115 degrees C). It also has a ow-limiting device that will restrict the ow of gas to 10 cubic
feet per hour (0.28 cubic meters per hour).

11
Installation
Before each use, check the gas hose for excessive abrasion, or wear, or cuts. Replace a hose assembly
showing those signs with the hose assembly specied in the parts list before using the griddle.
TO CONNECT THE CYLINDER TO THE REGULATOR AND HOSE
1. Be sure the LP cylinder is “OFF” by turning the hand wheel clockwise until it stops.
2. Place the cylinder on the back beside of body with valve facing outward. See the assembly instructions to
secure.
3. Be sure all burner controls are turned to the “OFF” position.
4. Remove the safety cap from the cylinder valve.
5. Center the nipple of the regulator into the cylinder valve.
6. Turn the black nut clockwise until it stops. Hand tighten only. Do not use a wrench.
WARNING
Always keep the gas cylinder in the upright position at all times.
WARNING
1. Do not connect this griddle to any unregulated sources of propane.
2. Before each use, check the gas hose for excessive abrasion, or wear, or cuts. Replace a hose assembly
showing those signs with the hose assembly specied in the parts list before using the griddle. Inspect the
hose assembly underneath the side burner and following the regulator hose up to its connection to the gas
manifold assembly.
3. Always perform the leak test listed below before using your griddle for the rst time, if the cylinder has been
changed, any gas components have been changed, the regulator ow-limiting device has been activated,
or after a long period of non-use.
4. Do not attempt to connect this griddle to the LP system of a motor home or trailer.
LEAK TESTING THE REGULATOR, VALVES, HOSES, AND CONNECTIONS
1. Ensure the LP cylinder valve and all burners are “OFF”.
2. Ensure the LP cylinder is connected to the regulator.
3. If the steps above are not followed exactly, a re causing death or serious injury may occur.
4. Mix a solution of 50% water and 50% liquid dish soap. Do not use any household cleaner solution.
5. Open the LP tank valve by turning the hand wheel counterclockwise one turn. If you hear a rushing sound,
turn the gas off immediately. In that case, there could be a leak at the connection. Reconnect the cylinder
to the regulator.
6. Spray or brush on the solution covering the following areas:
- Cylinder welds.
- Regulator and cylinder connection.
- Gas hose connections to the regulator
- All gas hoses
- All gas hose connections to the burners including the main and side burners.
7. Growing bubbles on any of the parts and connections listed above indicate a gas leak. Immediately shut off
the LP tank valve by turning the valve clockwise. Retighten the connections or order replacement parts as
needed. Continue to test as necessary until no leaks are detected.

12
Installation
Operation
8. Close the LP tank valve by turning the hand wheel clockwise.
WARNING
1. Do not use the griddle if you cannot stop the leaks. Be sure the LP cylinder valve is closed. If the LP
cylinder is still leaking, contact your LP dealer or local re department.
2. Do not use any match or open ame, or smoke, during leak testing.
3. Do not light a burner during leak testing.
4. The replacement hose assembly must be the one identied.
FOR YOUR SAFETY
1. Minimum clearance from the sides and back of units to adjacent combustible construction below top of unit,
36” (91 cm) from sides and 36” (91 cm) from back.
2. Do not locate this outdoor cooking gas appliance under overhead-unprotected combustible surfaces.
WARNING
1. Do not use this griddle in any enclosed area, garage, shed, or under any type of overhead structure or
canopy.
2. Operate this grill only in a well ventilated area.
WARNING
Do not face the griddle directly into the wind.
WARNING
Keep the fuel supply hose away from any heated surfaces and water.
1. Your gas griddle requires reasonable care during operation. It will be hot during cooking and cleaning. You
should never leave the griddle unattended or move the griddle when in use.
2. Children should never use your gas griddle. Keep younger children and pets away when in use.
3. Only use your gas griddle outside in a well ventilated area. Never use indoors in any building, garage,
shed, or under any type of ammable canopy or overhang.
4. Ensure your griddle is on level ground and the locking casters are locked before use.
5. Turn all gas valves off should the burners go out when cooking. Wait 5 minutes before relighting.
6. Do not lean over the griddle or touch the edges when in use.
7. Turn the burners off, and shut off the LP cylinder should a grease re occur.
8. Do not obstruct the ow of combustion and ventilation air to the griddle.
9. Keep the outdoor cooking gas appliances area clear and free from combustable materials, gasoline, and
other ammable vapors and liquids.
10. Keep the ventilation openings of the cylinder enclosure free and clear from debris.
11. Do not put a barbeque cover or other ammable material in the storage area of this griddle.
12. Do not install or use on or in a recreational vehicle, including boats.

13
Operation
LP GAS AND CYLINDER INFORMATION
Your new gas griddle operates on LP gas. It is odorless, colorless, and non-toxic when produced. You can
smell LP gas as it has been given an odor for your safety.
Your griddle uses the newest and safest LP Gas Cylinder.
1. O.P.D. (Overll Protection Device) - prevents accidental gas leaks caused by overlling of the tank. Each
tank contains a oat that closes the input valve when the tank is 80% full. This allows room for the LP gas
to expand in hot temperatures. A triangular hand wheel distinguishes this type of tank.
2. Q.C.C.1 Type 1 Quick Connect Valve - provides fast tank hookups and requires only to be tightened by
hand.
In addition, the LP tank you use with your griddle must meet the following requirements:
1. Required Measurements: 12.5” (317mm) in diameter and 18.5” (472mm) in height.
2. 20 lb (9.1 kg) propane cylinder.
3. Constructed and marked in accordance with the specications for LP Gas Cylinders of the U.S. Department
of Transportation (D.O.T.) or the National Standard of Canada (CAN/CSA-B339).
4. Provided with a listed overlling prevention device.
5. Provided with a cylinder connection device compatible with the connection of outdoor cooking appliances.
6. A means for vapor withdrawal.
7. Other cylinders may be acceptable for use with the appliance provided they are compatible with appliance
retention means and accompanied by illustration(s) depicting the cylinder mounted to the appliance utilizing
the cylinder retention means and the point of contact between the cylinder and the retention means.
LIGHTING
Always visually inspect your grill before lighting. Replace any hoses that are frayed or cracked before lighting
your griddle. Look for anything that may be blocking spaces for ventilation and remove. After lighting, always
check the ame to ensure you have a good ame all along each burner. If not able to light, or the ame is not
even along the entire burner(s), then see the Troubleshooting section.
WARNING
1. Read instructions before lighting.
2. If ignition does not occur in 5 seconds, turn the burner control(s) off, wait 5 minutes and repeat the lighting
procedure as below.
LIGHTING THE MAIN BURNERS USING THE IGNITOR
1. Ensure all burner control knobs are in the off position.
2. Turn on the LP gas by turning the hand wheel on the cylinder valve.
3. Turn one burner control knob marked with an igniter ame to high.
4. Press the igniter button and hold down. You should hear a clicking sound, which indicates the igniter is
working.
5. If the burner does not light within 5 seconds, turn the burner control knob to “OFF”. Wait 5 minutes for the
gas to clear, and repeat the above procedure. Use the manual directions below if it still will not light.

14
Operation
Maintenance
6. When lit, turn the control knob to the desired setting.
7. Your griddle is equipped with continuous ignition. Simply turn the control knob next to the lit burner to hi. It
will light automatically. There is no need to press the igniter again. Adjust the control knob(s) to the desired
setting.
MANUALLY LIGHTING THE MAIN BURNERS WITH A MATCH STICK
1. Ensure all burners are in the off position.
2. Slowly turn on the gas at the LP tank valve if it is not already on.
3. Place a match in the match holder located in the top center drawer of the grill cabinet underneath the right
main burner.
4. Use the holder to slide the lit match through the cooking grates and the front of the heat tent to the left of
the burner you wish to light.
5. Press and turn the burner control knob to “HI/LIGHT”, continue to push in and hold up to 5 seconds or until
the burner lights.
6. If the burner does not light within 5 seconds, turn the burner control knob to off. Wait 5 minutes for the gas
to clear, and try again.
7. When lit, turn the control knob to the desired heat setting.
TURNING OFF YOUR GRIDDLE
1. Turn off the gas supply at the LP tank by turning the valve clockwise.
2. Turn all burner control knobs to the off position.
CLEANING YOUR GRIDDLE
WARNING
1. Do not clean any part of your griddle in a self cleaning oven.
2. Do not use oven cleaners, abrasive kitchen cleaners, cleaners that contain citrus products, or mineral
spirits.
3. Do not use any type of steel bristled brush.
4. Clean your griddle regularly to stop grease build ups and avoid a grease re or excessive are ups.
5. Always allow your griddle to cool down before cleaning.
OTHER EXTERIOR SURFACES - Was with a mild dish soap and warm water. A cloth, soft brush, or plastic
cleaning pad can be used. Rinse thoroughly and wipe dry.
GREASE PAN - Check after use. Remove and clean the pan as grease builds up. It can be washed with warm
water and mild dish soap.

15
Maintenance
IGNITER - Visually inspect for cracks. Replace if a crack is found. Do not use water to clean the igniter.
BURNERS - We recommend you clean your burners at least twice a year, or before use if the griddle has not
been used in over one month.
GRIDDLE SURFACE
1. Immediately after using the griddle, turn heat to the low position. While hot, the griddle top should be
washed with water and a lint free cloth.
2. Keep the griddle on low heat until the griddle is completely dry. Turn off the griddle and allow to cool
completely before proceeding.
3. Liberally rub cooking oil on the griddle with a lint free cloth.
4. Turn the griddle back on to the low position until you see a thin layer of oil forming. Wipe off the excess oil
with a clean, lint free cloth.
5. Turn off the griddle and allow to cool completely before putting on the griddle cover. Store in a dry place to
prevent rusting.
WARNING
Small insects, such as spiders, are able to access the burner tubes. Sometimes they will build nests or webs
and as a result will block the burner. Do not use the griddle until all blockages are cleaned from the burners.
CLEANING THE BURNERS
1. Ensure the Gas is turned off at the cylinder.
2. Remove the griddle top.
3. Remove the cotter pins located underneath the back end of each burner.
4. Lift each burner up and out.
5. Clean the inside of the burner using a stiff wire. An alternative way to clean the inside of the burner is by
using compressed air, always use eye protection if using this method. Never enlarge the burner ports
during cleaning.
6. Brush the outer surface of the burner.
7. Ensure all ports (holes) a free of all debris.
8. Inspect the burner, replace if there are any cracks or enlarged holes.
9. Reinstall the burners by following these instructions in reverse
WARNING: Properly locating the burner with respect to the orice is vital for safety.
10. Secure the back of the burners to the body with the cotter pins.
11. Replace the griddle top.
12. Perform a leak test.
BURNER FLAMES
Always inspect the burner ame after lighting. A good ame should look almost completely blue with a yellow
tip. If the ame is mostly yellow with very little blue ame, the burner has build up and should be cleaned
before use.

16
Maintenance
ALWAYS
1. Keep the grilling area clear and free from combustible materials, gasoline and other ammable vapors and
liquids.
2. Do not obstruct the ow of combustion and ventilation air.
3. Keep the ventilation openings of the cylinder enclosure free and clear from debris.
IGNITER MAINTENANCE
The igniter is powered by 1 AA size battery. Replace the batter when necessary. Unscrew the igniter top, place
a new battery into the igniter with the positive (+) end facing up, then screw the igniter top back into place.
GRIDDLE STORAGE
1. Clean the griddle before storage.
2. Storage of the gas griddle indoors is only allowed if the LP gas cylinder is disconnected and removed from
the gas griddle.
3. Cover the griddle.
4. Perform a leak test before use after storage.

17
Troubleshooting
PROBLEM CAUSE SOLUTION
Burner will not light. Gas supply is turned off. Turn on gas at LP tank.
Out of propane. Check to be sure you still have
propane in the tank.
Regulator is not properly seated
into the tank valve.
Remove and reattach, hand tighten
only.
Crimped fuel supply hose. Inspect and straighten.
Regulator failure or damaged
hose.
Order replacement part and
replace.
Igniter not making clicking sound. Replace battery.
Igniter electrode coated in grease
or dirt.
Remove grease and dirt with
rubbing alcohol.
Electrode cracked or broken. Order replacement part and
replace.
Blockage in the gas system. Inspect the burners to be sure
insects, spider webs, ect are
removed.
Inspect under the control panel to
be sure the burners are aligned
properly with the valves.
Irregular ame or yellow ame. New burner may have residual oil. The oil will burn off naturally.
Tubes in burners are blocked. Remove and clean.
Burners have a high grease or dirt
build-up.
Remove and clean.
Burners are not aligned properly
with the valves.
Inspect under the control panel.
Sudden drop in gas pressure or
ames blow out.
Out of propane. Check to be sure you still have
propane in the tank.
The Excessive fuel ow valve has
been tripped.
Turn off all burners, wait 30
seconds and relight grill.
Inspect the gas hose, perform a
leak test and replace.
Turn on the gas at the LP tank rst
before turning the control knobs.
Tank was improperly purged, call
your LP gas dealer.
Wind could be blowing out the
burners.
Move the griddle out of the wind.

18
Troubleshooting
Fire behind the control panel. Immediately shut off the LP tank
valve and allow griddle to cool.
Check the burners for obstructions
and clean.
Inspect under the control panel
and make sure that the burners are
aligned correctly.
Perform a leak test, tighten or
replace parts as necessary.
REFERENCE
Item Number Model Number Description Manufacturer Model
Number
43022 GR-CN-0914 Outdoor Griddle Portable Propane Gas
36” / 914mm Wide 48,000 BTU CSA GD430
Parts Breakdown
Model GR-CN-0914 43022
Item No. Description Position Item No. Description Position Item No. Description Position
77981 Griddle Top for GD430 1 77985 Left Leg for GD430 6 72272 Oil Cup for GD430 11
77982 Gas Tank Hook for GD430 2 77986 Gas Tank Holder for GD430 7 77990 Body for GD430 12
72271 Side Shelf for GD430 3 77987 Casters for GD430 8 77991 Extension Wire for GD430 13
77983 Side Handle for GD430 4 77988 Fence Rail for GD430 9
77984 Knob for GD430 5 77989 Right Leg for GD430 10

19
Parts Breakdown
Model GR-CN-0914 43022

20
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
This manual suits for next models
1
Table of contents
Other Omcan Griddle manuals
Popular Griddle manuals by other brands

Farberware
Farberware 201795 manual

Blue Seal
Blue Seal Evolution GP514 Installation and operation manual

Chef's Choice
Chef's Choice G880000 quick guide

Wells
Wells G13 Installation use & care parts lists wiring diagrams

CUISIMAT
CUISIMAT PS 400G Instructions for use and installation

Dash
Dash DFAMG01 Instruction manual and recipe guide