Omcan Santos 01P User manual

Revised - 09/22/2022
Toll Free: 1-800-465-0234
Fax: [phone]
Email: [email protected]
www.omcan.com
Santos Pepper Grinder
Model Santos 01P
Item 46080
Instruction Manual

2
Page
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 6
-------------------------------------------------------------------------- 6
--------------------------------------------------------------------------------------------- 6
------------------------------------------------------------------------------------- 7 - 8
------------------------------------------------------------------------------ 9 - 10
---------------------------------------------------------------------------- 11 - 12
---------------------------------------------------------------------------- 13
------------------------------------------------------------------------------------------------- 14
---------------------------------------------------------------------------- 15
Table of Contents
Section
General Information
Safety and Warranty
Technical Specications
Operation
Maintenance
Figure Drawings
Parts Breakdown
Electrical Schematics
Notes
Warranty Registration
Model Santos 01P

3
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has su󰀨ered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.

4
General Information
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de
funcionamiento y seguridad.
Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para
salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el
envío del equipo si servicio técnico o devolución de la máquina que se requiere.
Safety and Warranty
IMPROPER USE
1. Do not use this appliance for grinding anything other than peppers.
2. Never operate the appliance with no peppers in the container.
3. Remove from the peppers any foreign bodies which may damage the grinding wheels (metal staples,
stones, etc.).
4. For electrocution risk protection reasons, never plunge the base into water or any other liquid.
5. Use a hose nor a pressure hose for cleaning: this is forbidden.

5
6. Never touch the moving parts.
7. Unplug the appliance before carrying out any work on it: cleaning, maintenance or repair.
8. Use the appliance if the power cord is damaged. It must be replaced by a special assembly available from
an approved Omcan dealer or from Omcan itself.
9. The use of spare parts other than certied Omcan original parts is prohibited.
10. Turn the On/O󰀨 switch (13) to “0” when the appliance is not operating.
11. Connect several appliances to the same power socket.
12. Use the appliance outdoors.
13. Never place the appliance close to or on a source of heat.
14. This appliance is a professional machine designed exclusively for professional use. It is not designed for
household use.
15. This appliance is not designed for use by people (including children) whose physical, sensorial or mental
capacities are impaired or by people with no experience or knowledge, unless they have been supervised
or given training in the use of the appliance beforehand by a person responsible for their safety. Supervise
children to ensure they do not play with the appliance.
16. This appliance is intended for use in communal areas, e.g. in the kitchens of restaurants, canteens,
hospitals and artisan trades such as bakeries, butcher’s shops, etc., but not for continuous mass
production of food.
The machine should be connected to a standard 2-pole + ground electric socket. The system should be tted
with an RCD and a fuse rated at 16A. The appliance must be grounded.
• Before connecting the machine, check that the mains electrical voltage is the same as the voltage for your
appliance. Its value is shown:
- On the identication plate under the machine.
- On the identication plate on the last page of this manual.
• Check that the On / O󰀨 switch (13) is in the 0 position before connecting the power cable plug to your
mains electric power socket (g. A).
RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure
or other damages resulting from installation in non-commercial or residential applications. The right
is reserved to deny shipment for residential usage; if this occurs, you will be notied as soon as
possible.
1 YEAR PARTS AND LABOUR BENCH WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule a drop o󰀨 to either
an Omcan authorized service depot in the area, or to an Omcan Service warehouse to repair the
equipment.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see https://omcan.com/disclaimer for complete info.
Safety and Warranty

6
Model Santos 01P
Electrical 120V / 60Hz
Power 650W
RPM 1800
Production per Hour 30.9 lbs. / 14 kgs.
Hopper Capacity 2.2 lbs. / 1 kgs.
Drawer Capacity 1.8 lbs. / 0.8 kgs.
Maximum Bag Height 5.9” / 150mm
Dimensions 12.6” x 9.8” x 21.7” / 320 x 250 x 550mm
Packaging Dimensions 16.1” x 11.8” x 22.6” / 410 x 300 x 575mm
Weight 33.1 lbs. / 15 kgs.
Packaging Weight 35.3 lbs. / 16 kgs.
Item Number 46080
Technical Specications
Operation
USING THE APPLIANCE
ADJUSTING THE GRIND
• Turn the grinding-wheel gap adjuster button 6 clockwise for a coarser grind and anticlockwise for a ner
grind. The factory setting is for the nest grind, the grinding-wheels nearly touching each other.
Safety and Warranty
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without di󰀩culty.
In any case, for suitable recycling, we suggest disposing of the products separately (di󰀨erentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

7
Maintenance
SERVICING
• Clean the pepper outlet, the pepper holder and the grinding mechanism from time to time. Always turn the
appliance o󰀨 (switch 13 on position 0) and unplug it.
MAINTENANCE
Before carrying out any work on the appliance, it must in all cases be unplugged from the mains power supply
and the motor start capacitor discharged.
DISCHARGING THE CAPACITOR
Use a screwdriver with insulated handle to touch the 2 connectors on the capacitor. The appearance of an
electric arc shows that the capacitor has discharged.
SPARE PARTS
This machine requires no specic maintenance. The bearings are lubricated for life. If work is required to
replace worn parts such as the grindstones or the electric or other components, refer to the parts list (see
exploded view at the end of the manual).
PROLONGED PERIODS OF NON-USE
There are no problems with this appliance in the event of prolonged periods of non-use. You are simply
advised to clean it before use and check that the components of the appliance are in good condition (e.g.
power cord, seals and other spare parts).
REPLACING THE GRINDSTONES
IMPORTANT: always change both 2 grindstones (17) at the same time.
The 2 grinding wheels are identical and can be tted equally either on the moving plate (18) (moving grinding
wheel) or on the cast metal adjustment block (19) (xed grinding wheel).
1. Stop the machine by putting the switch (13) to “0” and disconnect the power supply cord.
2. Close the shutter (3) on the bean hopper (2). Take o󰀨 the bean hopper (2).
3. Turn the grinding wheel gap adjuster button (6) clockwise until it comes to a halt at the “COARSE” setting.”
4. Unscrew the nuts (16) and remove the whole grinding unit (15), to gain access to the grinding wheels.
5. Change the grinding wheels (3 fastening screws) after carefully cleaning the supporting surfaces.
TAKE CARE: The slightest small pepper particle under the grinding wheel may prevent the machine
from operating correctly. It is recommended that the grinder body is cleaned with a compressed air
jet or a dry brush.
6. Reassemble the grinding unit (15) and adjust the grinding gap to its minimum setting.
Before tightening the fastening nuts (16) on the grinding unit (15), check that the dial (4) of the grinding
wheel adjuster button (6) is set to “COARSE”. This precaution is essential to prevent any risk of the
grinding wheels being brought too close to each other, which could cause damage to the grinding unit.

8
Maintenance
ADJUSTING THE MINIMUM GAP BETWEEN THE GRINDING-WHEELS
This should be done after replacing the grinding wheels.
1. Plug the appliance in and run it empty.
2. Unscrew hexagon socket screw (7) on the dial (4) using a 2-mm Allen wrench. Check that the dial (4) is
free to rotate without turning button (6).
3. Turn button (6) anticlockwise until the grinding wheels come into contact (a slight sound of friction will be
heard) then back one notch in the reverse direction.
ATTENTION This is a delicate operation, and prolonged contact between the grinding wheels
should be avoided, since this could damage them.
4. Turn the appliance o󰀨 by placing switch (13) on “0”.
5. Without moving the button (6), place the dial (4) on the “FINE” position then tighten the hexagon socket
screw (7) fully home.
6. Run the machine empty to check that the grinding wheels rotate without touching each other on the nest
setting. If this is not the case, repeat the above procedure.
FAULT FINDING
In every case: If the problem persists, switch o󰀨 the power supply to the machine (unplug the cord from the
mains socket) and call in the maintenance service or contact a Omcan approved dealer.
THE MACHINE WILL NOT START
• Check: the mains power supply and the condition of the power supply cord.
• Note: the switch should be lit when on the “1” position.
• Check that there are no foreign bodies stuck between the grinding wheels.
THE MACHINE STOPS BECAUSE THE MOTOR HAS OVERHEATED
• The metal casing around the motor unit is hot.
• In the event of overheating, the motor stops.
• The overheating protection system resets automatically; wait for the motor to cool (15 to 30 minutes),
before restarting the machine.
THE MACHINE STOPS BECAUSE OF AN OVERLOAD
If the motor is blocked (foreign body, something too hard), the excess current protection system (14), located
under the appliance will be triggered automatically and cut o󰀨 the electrical power to the motor.
• Set the On / O󰀨 switch (13) to “0” position, disconnect the appliance.
• Correct the fault then press the excess current protection button (14).
• Press the On/O󰀨 switch (13) (position I).
If the problem persists, check the following points:
• Check that the grinding wheels do not touch each other.
• Check the state of wear of the grinding wheels (grinding too ne with worn grinding wheels can result in a
motor overload like this).
• If there are no foreign bodies preventing the appliance from working, then check and replace the motor
starter relay then the capacitor.

9
Figure Drawings

10
Figure Drawings

11
Parts Breakdown
Model Santos 01P 46080

12
Parts Breakdown
Model Santos 01P 46080
Item No. Description Position Item No. Description Position Item No. Description Position
40659 Set of 2 Grinding Discs (Standard) for
46080 00001 AC598 Screw CHC 5x15 for 46080 01230 AC647 Washer AZ 4 ZN for 46080 01404
40662 Complete Hopper with Obturator for
46080 01100 AC599 Cap Nut H M6 for 46080 01231 AC648 Rubber Foot D 25 for 46080 01406
63502 Lid for 46080 01101 AC600 Washer Diam 6 for 46080 01232 AC649 Washer 5x12 for 46080 01407
AC566 Hopper for 46080 01102 AK382 Grind Core for 46080 01238 AC650 Screw TCL 5.5x16 ZN for 46080 01408
40663 Obturator for 46080 01103 AK383 Complete Grind Core 60Hz for 46080 01239B AC655 Capacitor Screw for 46080 01414
AC567 Obturator Handle for 46080 01104 AK384 Ondulated Washer 6202 for 46080 01259 AC656 Nut H M4 ZN for 46080 01415
AK379 Screw CX 4x70 Zn for 46080 01105N AC617 Complete Motor Single Phase 110V 60Hz
for 46080 01300B AC659 Power Cord with USA Plug for 46080 01419
AC570 Belleville Washer 5x12 for 46080 01107 AC618 Complete Front Flange (Brown) for 46080 01301 AC660 Screw H 4.2x12.7 ZN for 46080 01422
AC571 Safety Bar for 46080 01109 AC619 Front Flange Only (Brown) for 46080 01302 AC661 Special On-Off Multifunctions Switch
230V 8A115V for 46080 01435B
AK380 Complete Grind Housing 60Hz for 46080 01200B AC620 Bearing 6202 for 46080 01303 AC662 Cap D12.2x6.2 Black for 46080 01436
AC573 Grind Housing with Adjusting Button
for 46080 01201 AC621 Bearing Washer (Thin) for 46080 01304 AK385 Screw H 5x10 Zn for 46080 01444
AC574 Adjusting Button for 46080 01202 AC622 Screw M4x16 for 46080 01305 AC667 Screw H M5x12 ZN Autotar for 46080 01445
AC575 Index for 46080 01203 AC623 Screw H M6x20 ZN for 46080 01307 AK386 Starting Relay 100-120V 50/60Hz for
46080 01446V1
AC576 Graduated Round Plate for 46080 01204 AC624 Bearing Washer (Thick) for 46080 01309 AC669 Capacitor Ring D46 for 46080 01448
AC577 Bearing Washer for 46080 01205 AC625 Complete Rear Flange for 46080 01310 AK387 Capacitor 75 µF Diam 46 for 46080 01449
AC578 Bearing 6202 for 46080 01206 AC626 Rear Flange Only Brown for 46080 01311 AC670 Painted Base for 46080 01451
AC579 Steel Ball D 6 for 46080 01207 AC627 Chromed Bearing Washer for 46080 01312 AC671 Complete Bottom Plate 115V for 46080 01452B
AC580 Adjusting Button Spring for 46080 01208 AC628 Screw H 4x10 for 46080 01313 AC672 Bottom Plate for 46080 01453
AC581 Screw HC M4x8 for 46080 01209 AC629 Bearing 6202 for 46080 01314 AC683 Complete Drawer with Sustainer+Screws
for 46080 01500
AC582 Screw H 4x8 ZN for 46080 01210 AC632 Screw 6x35 for 46080 01317 AC684 Drawer Sustainer Only for 46080 01501
AC583 Screw H 4x8 ZN for 46080 01211 AC633 Nut H M6 ZN for 46080 01318 40667 Grater Drawer for 46080 01502
AC584 Screw CB M5x35 ZN for 46080 01212 AC634 Washer 6x18x1 for 46080 01319 AC685 Screw TF M4x10 ZN for 46080 01503
AC585 Grind Adjustment Screw for 46080 01213 AC635 Pin 3x5 for 46080 01323 AC686 Complete Bag Holder for 46080 01600
AC586 Grind Housing for 46080 01214 AC636 Assembling Threaded Rod M5x134 for
46080 01335 AC688 Bakelite Ball for 46080 01602
AC587 Washer AZ 5 for 46080 01215 AC637 Cap Nut H M5 for 46080 01336 AC689 Bag Holder Spring for 46080 01603
AC588 Screw H 5x10 ZN for 46080 01216 AC638 Stainless Steel Motor Protector for 46080 01337 AC690 Complete Bag Holder Axle for 46080 01604
AC589 Screw CB M4x10 ZN for 46080 01217 AC639 Motor Protector Spring for 46080 01338 AC691 Rubber Buffer D12 H 7.5 for 46080 01607
AC593 Screw M4x10 for 46080 01223 AC640 Ondulated Washer 6202 for 46080 01340 AC693 Screw FZ M3x6 for 46080 01610
AK381 Complete Feeding Screw (Pepper) 60Hz
for 46080 01225B AC641 Complete Rotor with Shaft - Single Phase and Pin for 46080 01360 AK388 Bag Holder Sole for 46080 01621
AC595 Feeding Screw for 46080 01226 AC642 Complete Stator (Winding) 110V 60Hz
for 46080 01365B AK389 Pepper Output for 46080 01630
AC596 V Ring Gasket V20 for 46080 01228 AC643 Stator Only Single Phase 110V 60Hz
for 46080 01366B AK390 Outlet Chute Axle for 46080 01631
AC597 Washer 5x20 for 46080 01229 AC644 Complete Base - 1 Phase 110-120V 60
Hz for 46080 01400B AK391 Bag Holder Tube (Polished) for 46080 01632

13
Electrical Schematics
Model Santos 01P 46080

14
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________

15
Warranty Registration
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear o󰀨 the card at
the perforation and then send to the address specied below. You can also register online by visiting:
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
Canada, L5L 4X5
https://omcan.com/warranty-registration/
or email to: [email protected]
Purchaser’s Information
Name: Company Name:
Address:
Telephone:
City: Province or State: Postal or Zip: Email Address:
Country: Type of Company:
Restaurant Bakery Deli
Dealer from which Purchased: Butcher Supermarket Caterer
Dealer City: Dealer Province or State: Institution (specify):
Invoice: Other (specify):
Model Name: Model Number: Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):
Would you like to extend the warranty? Yes No

Por correo en Canadá
Pour postale au Canada
For mailing in Canada
Por correo en los EE.UU.
Pour di󰀨usion aux États-Unis
For mailing in the US
OMCAN
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
Niagara Falls, New York
USA, 14305
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan

Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualied local sales
and service representatives who provide convenient access to over 6,500 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 6500
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 6,500 productos con origen a nivel mundial.