Omega Engineering OM5-C User manual

OMEGAnetSM On-Line Service
http://www.omega.com
Internet e-mail
[email protected]
Servicing North America:
USA: One Omega Drive, Box 4047
Stamford, CT 06907-0047
Tel: [phone]
e-mail: [email protected] FAX: [phone]
Canada: 976 Berger
Laval (Quebec) H7L 5A1
Tel: [phone]
e-mail: [email protected] FAX: [phone]
For immediate technical or application assistance:
USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGASM
Customer Service: 1-800-622-2378 / 1-800-622-BESTSM
Engineering Service: 1-800-872-9436 / 1-800-USA-WHENSM
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
Mexico and
Latin America: Tel: (95) 800-TC-OMEGASM
En Espanol: (95) 203-359-7803 FAX: [phone] e-mail: [email protected]
Servicing Europe:
Benelux: Postbus 8034, 1180 LA Amstelveen, The Netherlands
Tel: [phone]
Toll Free in Benelux: 06 0993344
e-mail: [email protected]
FAX: [phone]
Czech Republic: ul. Rude armady 1868
733 01 Karvina-Hranice
Tel: [phone]
e-mail:[email protected] FAX: [phone]
France: 9, rue Denis Papin, 78190 Trappes
Tel: [phone]
Toll Free in France: 0800-4-06342
e-mail: [email protected]
FAX: [phone]
Germany/Austria:Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
Tel: [phone]
Toll Free in Germany: 0130 11 21 66
e-mail: [email protected]
FAX: [phone]
United Kingdom: 25 Swannington Road,
Broughton Astley, Leicestershire,
LE9 6TU, England
Tel: [phone]
FAX: [phone]
P.O. Box 7, Omega Drive,
Irlam, Manchester,
M44 5EX, England
Tel: [phone]
FAX: [phone]
Toll Free in England: 0800-488-488
e-mail: [email protected]
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that
apply. OMEGA is constantly pursuing certification of its products to the European New Approach
Directives. OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct but OMEGA Engineering, Inc. accepts
no liability for any errors it contains, and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient connected applications.

1
GENERAL DESCRIPTION .............................................................................................................. 2
OM5 SELECTION GUIDE ............................................................................................................... 2
ANALOG VOLTAGE INPUT MODULES, NARROW BANDWIDTH: OM5-IMV/IV ....................... 4
ANALOG CURRENT INPUT MODULES: OM5-II .......................................................................... 6
TRUE RMS INPUT MODULES: OM5-IAC ..................................................................................... 8
LINEARIZED 2- OR 3-WIRE RTD INPUT MODULES: OM5-IP/IC/IN .............................................. 10
LINEARIZED 4-WIRE RTD INPUT MODULES: OM5-IP4/IC4/IN4.............................................. 12
POTENTIOMETER INPUT MODULES: OM5-PT ......................................................................... 14
THERMOCOUPLE INPUT MODULES: OM5-ITC ........................................................................ 16
STRAIN GAGE INPUT MODULES, WIDE BANDWIDTH: OM5-WBS ....................................... 16
ANALOG CURRENT OUTPUT MODULES: OM5-IVI ................................................................. 20
ANALOG VOLTAGE INPUT MODULES, WIDE BANDWIDTH: OM5-WMV/WV ....................... 22
2-WIRE TRANSMITTER INTERFACE MODULES: OM5-TX ............................................................ 24
GENERAL PURPOSE INPUT MODULES, DC EXCITATION: OM5-DT .................................... 26
FREQUENCY INPUT MODULES: OM5-IFI ................................................................................ 28
LINEARIZED THERMOCOUPLE INPUT MODULES: OM5-LTC ...................................................... 30
VOLTAGE OUTPUT MODULES, 50mA DRIVE CAPACITY: OM5-AV ...................................... 32
DIMENSIONS AND ACCESSORIES ............................................................................................ 34
TABLE OF CONTENTS

22
OM5-WMV/WV
Analog Voltage Input Modules, Wide Bandwidth
FEATURES
●ACCEPTS MILLIVOLT AND VOLTAGE LEVEL SIGNALS
●HIGH LEVEL VOLTAGE OUTPUTS
●1500Vrms TRANSFORMER ISOLATION
● ANSI/IEEE C37.90.1-1989 TRANSIENT PROTECTION
●INPUT PROTECTED TO 240VAC CONTINUOUS
●100dB CMR
●10kHz SIGNAL BANDWIDTH
●±0.05% ACCURACY
●±0.02% LINEARITY
●±1µV/°C DRIFT
● CSA CERTIFIED, FM APPROVED, CE COMPLIANT
●MIX AND MATCH OM5 TYPES ON BACKPANEL
FIGURE 1. OM5-WMV/WV Block Diagram.
DESCRIPTION
Each OM5 wide bandwidth voltage input module provides a single channel
of analog input which is amplified, isolated, and converted to a high level
analog voltage output (Figure 1). This voltage output is logic-switch
controlled, allowing these modules to share a common analog bus without
the requirement of external multiplexers.
The OM5 modules are designed with a completely isolated computer side
circuit which can be floated to ±50V from Power Common, pin 16. This
complete isolation means that no connection is required between I/O
Common and Power Common for proper operation of the output switch. If
desired, the output switch can be turned on continuously by simply
connecting pin 22, the Read-Enable pin to I/O Common, pin 19.
The input signal is processed through a pre-amplifier on the field side of
the isolation barrier. This pre-amplifier has a gain-bandwidth product of
5MHz and is bandwidth limited to 10kHz. After amplification, the input
signal is chopped by a proprietary chopper circuit. Isolation is provided by
transformer coupling, again using a proprietary technique to suppress
transmission of common mode spikes or surges. The module is powered
from +5VDC, ±5%.
A special input circuit provides protection against accidental connection of
power-line voltages up to 240VAC.
Anti-Aliasing
Filter
+In
–In
–EXC
Backpanel
Term Block
1
2
6
5
3
NC
Surge
Suppression
and
Protection
Isolated
Field-Side
Power
4
3
2
1
+EXC
–V
+V
V
IN
4
NC
–V
LPF
+V
Power
Oscillator
Isolated
Computer-Side
Power
V
OUT
20
22
I/O Common
RD EN\
+5V
17
16 Power Common
19
Isochopper™
Amplifier
Pat Pending

23
Module OM5-WMV OM5-WV
Input Range ±10mV to ±100mV ±1V to ±40V
Input Bias Current ±0.5nA ±0.05nA
Input Resistance
Normal 200MΩ650kΩ(minimum)
Power Off 40kΩ650kΩ(minimum)
Overload 40kΩ650kΩ(minimum)
Input Protection
Continuous 240Vrms Max *
Transient ANSI/IEEE C37.90.1-1989 *
CMV, Input to Output
Continuous 1500Vrms max *
Transient ANSI/IEEE C37.90.1-1989 *
CMR (50Hz or 60Hz) 100dB *
NMR (–3dB at 10kHz) 120dB per Decade above 10kHz *
Accuracy(1) ±0.05% Span ±10µV RTI(2) ±0.05%(VZ
(3))±0.05% span ±0.2mV RTI(2)
±0.05% (VZ
(3))
Nonlinearity ±0.02% Span *
Stability
Input Offset ±1µV/°C±20µV/°C
Output Offset ±40µV/°C*
Gain ±25ppm/°C±50ppm/°C
Noise
Input, 0.1 to 10Hz 0.4µVrms 2µVrms
Output, 100kHz 10mVp-p *
Bandwidth, –3dB 10kHz *
Rise Time, 10 to 90% Span 35µs*
Settling Time, to 0.1% 250µs*
Output Range ±5V or 0V to +5V *
Output Resistance 50Ω*
Output Protection Continuous Short to Ground *
Output Selection Time 6µs at Cload = 0 to 2000pF
(to ±1mV of VOUT )*
Output Current Limit ±8mA *
Output Enable Control
Max Logic “0” +0.8V *
Min Logic “1” +2.4V *
Max Logic “1” +36V *
Input Current, “0”, “1” 0.5µA*
Power Supply Voltage +5VDC ±5% *
Power Supply Current 30mA *
Power Supply Sensitivity ±2µV/% RTI(2) ±200µV/% RTI(2)
Mechanical Dimensions 2.28" x 2.26" x 0.60" (58mm x 57mm x 15mm) *
Environmental
Operating Temp. Range –40°C to +85°C*
Storage Temp. Range –40°C to +85°C*
Relative Humidity 0 to 95% Noncondensing *
Emissions EN50081-1, ISM Group 1, *
Class A (Radiated, Conducted)
Immunity EN50082-1, ISM Group 1, Class A (ESD, RF, EFT) *
ORDERING
INFORMATION
SPECIFICATIONS Typical at TA= +25°C and +5V Power.
* Same specification as OM5-
WMV.
NOTES: (1) Includes nonlinearity,
hysteresis and repeatability.
(2) RTI = Referenced to input.
(3) VZis the input voltage
that results in 0V output.
MODEL INPUT RANGE OUTPUT RANGE
OM5-WMV-10A-C –10mV to +10mV –5V to +5V
OM5-WMV-50A-C –50mV to +50mV –5V to +5V
OM5-WMV-100A-C –100mV to +100mV –5V to +5V
OM5-WMV-10B-C –10mV to +10mV 0V to +5V
OM5-WMV-50B-C –50mV to +50mV 0V to +5V
OM5-WMV-100B-C –100mV to +100mV 0V to +5V
OM5-WV-1A-C –1V to +1V –5V to +5V
OM5-WV-5A-C –5V to +5V –5V to +5V
OM5-WV-10A-C –10V to +10V –5V to +5V
OM5-WV-1B-C –1V to +1V 0V to +5V
OM5-WV-5B-C –5V to +5V 0V to +5V
OM5-WV-10B-C –10V to +10V 0V to +5V
OM5-WV-20A-C –20V to +20V –5V to +5V
OM5-WV-20B-C –20V to +20V 0V to +5V
OM5-WV-40A-C –40V to +40V –5V to +5V
OM5-WV-40B-C –40V to +40V 0V to +5V

24
OM5-TX
2-Wire Transmitter Interface Modules
ter. This allows a 2-wire loop powered transmitter to be directly connected
to the module without requiring an external power supply. The regulated
supply will provide a nominal +20VDC at a loop current of 4mA to 20mA.
The OM5-TX will provide a 1500V isolation barrier for non-isolated 2-wire
field transmitters. It can also be used when additional isolation is required
between an isolated 2-wire transmitter and the input stage of the control
room computer.
The voltage output is logic switch controlled, which allows these modules
to share a common analog bus without the requirement of external
multiplexers.
The modules are designed with a completely isolated computer side circuit
which can be floated to ±50V from Power Common, pin 16. This complete
isolation means that no connection is required between I/O Common and
Power Common for proper operation of the output switch. If desired, the
output switch can be turned on continuously by simply connecting pin 22,
the Read-Enable pin to I/O Common, pin 19.
A precision 20Ωcurrent conversion resistor is supplied with the module.
Sockets are provided on the OM5-BP backpanels to allow installation of
this resistor. Extra resistors are available under part number OMX-1362-C.
All field inputs are fully protected from accidental connection of power-line
voltages up to 240VAC. The module has a 3dB bandwidth of 100Hz. Signal
filtering is accomplished with a six-pole filter, with two poles on the field
side of the isolation barrier, and the other four on the computer side.
FIGURE 1. OM5-TX Block Diagram.
FEATURES
●ISOLATED +20VDC CURRENT LOOP SUPPLY
●PROVIDES ISOLATION FOR NON-ISOLATED 2-WIRE
TRANSMITTERS
●HIGH LEVEL VOLTAGE OUTPUT: +1V to +5V or +2V to +10V
● 1500Vrms TRANSFORMER ISOLATION
●ANSI/IEEE C37.90.1-1989 TRANSIENT PROTECTION
●INPUT PROTECTED TO 240VAC CONTINUOUS
●100dB CMR
●100Hz SIGNAL BANDWIDTH
●±0.05% ACCURACY
●±0.02% LINEARITY
● CSA CERTIFIED, FM APPROVED, CE COMPLIANT
●MIX AND MATCH OM5 TYPES ON BACKPANEL
DESCRIPTION
Each OM5-TX 2-wire transmitter interface module provides a single chan-
nel which accepts a 4 to 20 mA process current input and provides a
standard +1 to +5V or +2 to +10V output signal (Figure 1). An isolated
+20VDC regulated power supply is provided to power the current transmit-
LPF
+In
–In
–EXC
Backpanel
Term Block
1
2
NC
4
6
5
3
Surge
Suppression
and
Protection
Isolated
Field-Side
Power
Isochopper™
Amplifier
Pat Pending
4
3
2
1
+EXC
–V
+V
–V+V
Isolated
Computer-Side
Power
NC
LPF V
OUT
20
19
22
I/O Common
RD EN\
Power
Oscillator
+5V
17
16 Power
Common
2-Wire
Transmitter
20 Ω
0.1% plug-in
OMX-1362-C
Isolated
Excitation
Source

25
SPECIFICATIONS Typical at TA= +25°C and +5V power.
ORDERINGINFORMATION
MODEL INPUT RANGE OUTPUTRANGE
OM5-TX-1-C 4mA to 20mA +1V to +5V
OM5-TX-2-C 4mA to 20mA +2V to +10V
NOTES: (1) Includes nonlinearity, hysteresis and repeatability.
(2) RTI = Referenced to input.
SCM5B
Module OM5-TX
Input Range 4mA to 20mA
Input Resistor
Value 20.00Ω
Accuracy ±0.1%
Stability ±10ppm/°C
Loop Supply Voltage Nominal 20V at 4mA to 20mA
Isolated Excitation Protection
Continuous 240Vrms max
Transient ANSI/IEEE C37.90.1-1989
Input Protection
Continuous 240Vrms max
Transient ANSI/IEEE C37.90.1-1989
CMV, Input to Output
Continuous 1500Vrms max
Transient ANSI/IEEE C37.90.1-1989
CMR (50 or 60Hz) 100dB
NMR (–3dB at 100Hz) 120dB per decade above 100Hz
Accuracy(1) ±0.05% span ±4µA RTI(2)
Nonlinearity ±0.02% span
Stability
Input Offset ±1µV/°C
Output Offset ±40µV/°C
Gain ±25ppm/°C of reading
Noise
Input, 0.1 to 10Hz 10nArms
Output, 100KHz 500µVrms
Bandwidth, –3dB 100Hz
Response Time, 90% span 4mS
Output Range +1V to +5V or +2V to +10V
Output Resistance 50Ω
Output Protection Continuous short to gnd
Output Selection Time 6µs at Cload = 0 to 2000pF
(to ±1mV of VOUT)
Output Current Limit +8mA
Output Enable Control
Max Logic “0” +0.8V
Min Logic “1” +2.4V
Max Logic “1” +36V
Input Current, “0, 1” 0.5µA
Power Supply Voltage +5VDC ±5%
Power Supply Current 180mA at transmitter load of 20mA
100mA at transmitter load of 4mA
Power Supply Sensitivity ±10µV/% RTI(2)
Mechanical Dimensions 2.28" x 2.26" x 0.60" (58mm x 57mm x 15mm)
Environmental
Operating Temp. Range –40°C to +85°C
Storage Temp. Range –40°C to +85°C
Relative Humidity 0 to 95% noncondensing
Emissions EN50081-1, ISM Group 1, Class A (Radiated, Conducted)
Immunity EN50082-1, ISM Group 1, Class A (ESD, RF, EFT)

26
OM5-DT
General Purpose Input Modules, with DC Excitation
controlled, which allows these modules to share a common analog bus
without the requirement of external multiplexers.
The modules are designed with a completely isolated computer side circuit
which can be floated to ±50V from Power Common, pin 16. This complete
isolation means that no connection is required between I/O Common and
Power Common for proper operation of the output switch. If desired, the
output switch can be turned on continuously by simply connecting pin 22,
the Read-Enable pin to I/O Common, pin 19.
The OM5-DT can interface to devices which require a precision 10VDC
excitation supply. The 1kHz bandwidth significantly reduces ripple and
noise inherent in these devices.
Transducer excitation is provided from the module by a very stable 10V
source. The excitation supply is fully isolated, allowing the amplifier inputs
to operate over the full range of the excitation voltage. This feature offers
significant flexibility in real world applications. Eight full scale input ranges
are provided, from ±1V to ±10V, producing ±5V full scale output.
The input signal is processed through a pre-amplifier on the field side of
the isolation barrier. This pre-amplifier has a gain-bandwidth product of
5MHz and is bandwidth limited to 1kHz. After amplification, the input signal
is chopped by a proprietary chopper circuit. Isolation is provided by
transformer coupling, again using a proprietary technique to suppress
transmission of common mode spikes or surges. The module is powered
from +5VDC, ±5%.
Special input circuits provide protection of the signal inputs and the
isolated excitation supply up to 240VAC.
FIGURE 1. OM5-DT Block Diagram.
FEATURES
●INTERFACES TO DC DISPLACEMENT TRANSDUCERS AND OTHER
DEVICES REQUIRING A STABLE DC SUPPLY
●HIGH LEVEL VOLTAGE OUTPUTS
● 1500Vrms TRANSFORMER ISOLATION
●ANSI/IEEE C37.90.1-1989 TRANSIENT PROTECTION
●INPUT PROTECTED TO 240VAC CONTINUOUS
●FULLY ISOLATED EXCITATION SUPPLY
●100dB CMR
●1KHz SIGNAL BANDWIDTH
●±0.10% ACCURACY
●±0.02% LINEARITY
●±20µV/°C DRIFT
● CSA CERTIFIED, FM APPROVED, CE COMPLIANT
●MIX AND MATCH OM5 TYPES ON BACKPANEL
DESCRIPTION
Each OM5-DT general purpose input module provides a single channel of
transducer input which is filtered, isolated, scaled, and converted to a high
level analog voltage output (Figure 1). This voltage output is logic switch
–V
LPF
+In
–In
–EXC
Backpanel
Term Block
6
5
3
Surge
Suppression
and
Protection +V
Isolated
Field-Side
Power
Power
Oscillator
Isolated
Computer-Side
Power
V
OUT
20
19
22
I/O Common
RD EN\
+5V
17
16 Power
Common
4
3
2
1
+EXC
–V
+V
4
Isolated
Excitation
Source
1
2
NC
NC
DC LVDT
or Other
Transducer
Isochopper™
Amplifier
Pat Pending
LPF

27
Module OM5-DT
Input Range ±1V to ±10V
Input Bias Current ±0.05nA
Input Resistance
Normal 2MΩ(minimum)
Power Off 2MΩ(minimum)
Overload 2MΩ(minimum)
Input Protection
Continuous 240Vrms max
Transient ANSI/IEEE C37.90.1-1989 (formerly IEEE-472)
Excitation Voltage, VEXC +10.0VDC ±2mV
Excitation current 40mA (maximum)
Excitation Load Regulation ±5ppm/mA
Excitation Stability ±15ppm/°C
Isolated Excitation Protection
Continuous 240Vrms max
Transient ANSI/IEEE C37.90.1-1989 (formerly IEEE-472)
CMV, Input to Output
Continuous 1500Vrms max
Transient ANSI/IEEE C37.90.1-1989 (formerly IEEE-472)
CMR (50 or 60Hz) 100dB
NMR (–3dB at 1kHz) 120dB per decade above 1kHz
Accuracy(1) ±0.1% span, ±0.2mV RTI2
Nonlinearity ±0.02% span
Stability
Input Offset ±20µV/°C
Output Offset ±40µV/°C
Gain ±50ppm/°C
Noise
Input, 0.1 to 10Hz 0.4µVrms
Output, 100KHz 5mVpp
Bandwidth, –3dB 1kHz
Response Time (to 90% final value) 750µs
Output Range ±5V
Output Resistance 50Ω
Output Protection Continuous short to ground
Output Selection Time 6.0µs at Cload = 0 to 2000pF
(to ±1mV of VOUT)
Output Current Limit ±8mA
Output Enable Control
Max Logic “0” +0.8V
Min Logic “1” +2.4V
Max Logic “1” +36V
Input Current, “0, 1” 0.5µA
Power Supply Voltage +5VDC ±5%
Power Supply Current 200mA @ Full Exc. load, 100mA @ No Exc. Load
Power Supply Sensitivity ±200µV/% RTI(2)
Mechanical Dimensions 2.28" x 2.26" x 0.60" (58mm x 57mm x 15mm)
Environmental
Operating Temp. Range –40°C to +85°C
Storage Temp. Range –40°C to +85°C
Relative Humidity 0 to 95% noncondensing
Emissions EN50081-1, ISM Group 1, Class A (Radiated, Conducted)
Immunity EN50082-1, ISM Group 1, Class A (ESD, RF, EFT)
SPECIFICATIONS Typical at TA= +25°C and +5V power.
SCM5B
NOTES:
(1) Includes excitation error, nonlinearity, hysteresis and repeatability.
(2) RTI = Referenced to input.
ORDERINGINFORMATION
MODEL MAXIMUM INPUT OUTPUT
OM5-DT-1-C ±1V ±5V
OM5-DT-2-C ±2V ±5V
OM5-DT-3-C ±3V ±5V
OM5-DT-4-C ±4V ±5V
OM5-DT-5-C ±5V ±5V
OM5-DT-6-C ±6V ±5V
OM5-DT-7-C ±7V ±5V
OM5-DT-8-C ±8V ±5V
OM5-DT-9-C ±9V ±5V
OM5-DT-10-C ±10V ±5V

28
OM5-IFI
Frequency Input Modules
FEATURES
●ACCEPTS FREQUENCY INPUTS OF 0 to 100kHz
●PROVIDES HIGH LEVEL VOLTAGE OUTPUTS
●TTL LEVEL INPUTS
●1500 VOLT TRANSFORMER ISOLATION
●ANSI/IEEE C37.90.1-1989 TRANSIENT PROTECTION
●INPUT PROTECTED TO 240VAC CONTINUOUS
●±0.05% ACCURACY
●MIX AND MATCH OM5 TYPES ON BACKPANEL
●CSA CERTIFIED, FM APPROVED, CE COMPLIANT
DESCRIPTION
Each OM5-IFI Frequency input module provides a single channel of fre-
quency input which is isolated and converted to a high level analog voltage
output. This voltage output is logic switch controlled, which allows these
modules to share a common analog bus without the requirement of external
multiplexers (Figure 1).
The frequency input signal can be a TTL level signal or a zero-crossing signal.
Terminal 3 (+In) on the field-side terminal block is the “common” or ground
connection for input signals. A TTL signal is connected from terminal 2 (–In)
to terminal 3 (+In), while a zero-crossing signal is connected from terminal 4
(+EXC) to terminal 3 (+In). Input circuitry for each of the signal types has
hysteresis built in. An input signal must cross entirely through the hysteresis
region in order to trigger the threshold comparator.
A 5.1V excitation is available for use with magnetic pick-up or contact-
closure type sensors. The excitation is available on pin 1 (–EXC) and the
excitation common is pin 3 (+In).
The modules are designed with a completely isolated computer side circuit
which can be floated to ±50V from Power Common, pin 16. This complete
isolation means that no connection is required between I/O Common and
Power Common for proper operation of the output switch. If desired, the
output switch can be turned on continuously by simply connecting pin 22,
the Read-Enable pin to I/O Common, pin 19.
A special circuit in the input stage of the module provides protection against
accidental connection of power-line voltages up to 240VAC.
FIGURE 1. OM5-IFI Block Diagram.
Threshold
Comparator
+In
–In
–
+
+
–
–EXC
Backpanel
Term Block
1
2
NC
6
5
3
5.1V
Surge
Suppression
and
Protection
Isolated
Field-Side
Power
4
3
2
1
+EXC
–V
+V
TTL
Inputs
4
–V
LPF
+V
Power
Oscillator
Isolated
Computer-Side
Power
V
OUT
20
22
I/O Common
RD EN\
+5V
17
16 Power Common
NC
19
Signal
Isolation
Zero-Crossing
Inputs
F to V

29
Module OM5-IFI
Input Range 0 to 100KHz
Input Threshold Zero Crossing
Minimum Input 60mVp-p
Maximum Input 350Vp-p
Minimum Pulse Width 4µs
TTL Input Low 0.8V max
TTL Input High 2.4V min
Input Hysteresis
Zero Crossing 0.04V
TTL 1.5V
Input Resistance
Normal 100KΩ
Power Off 100KΩ
Overload 100KΩ
Input Protection
Continuous 240Vrms max
Transient ANSI/IEEE C37.90.1-1989
Excitation +5.1V @ 8mA max
CMV, Input to Output
Continuous 1500Vrms max
Transient ANSI/IEEE C37.90.1-1989
CMR (50 or 60Hz) 120dB
Accuracy(1) ±0.05% span
Nonlinearity ±0.02% span
Stability
Offset ±40ppm/°C
Gain ±40ppm/°C
Noise
Output Ripple <10mVp-p @ Input >2% span
Response Time (0 to 90%)
OM5-IFI-500/1K-C 300 ms
OM5-IFI-3K-C 170 ms
OM5-IFI-5K/10K-C 90 ms
OM5-IFI-25K/50K/100K-C 20 ms
Output Range 0V to +5V
Output Resistance 50Ω
Output Protection Continuous short to ground
Output Selection Time 6µs at Cload = 0 to 2000pF
(to ±1mV of VOUT)
Output Current Limit +8mA
Output Enable Control
Max Logic “0” +0.8V
Min Logic “1” +2.4V
Max Logic “1” +36V
Input Current, “0,1” 0.5µA
Power Supply Voltage +5VDC ±5%
Power Supply Current 110mA
Power Supply Sensitivity ±150µV/% RTO (2)
Mechanical Dimensions 2.28" x 2.26" x 0.60" (58mm x 57mm x 15mm)
Environmental
Operating Temp. Range -40°C to +85°C
Storage Temp. Range -40°C to +85°C
Relative Humidity 0 to 95% noncondensing
Emissions EN50081-1, ISM Group 1, Class A (Radiated, Conducted)
Immunity EN50082-1, ISM Group 1, Class A (ESD, RF, EFT)
SPECIFICATIONS Typical at Ta = +25C and +5V Power
NOTES: (1) Includes nonlinearity, hysteresis and repeatability.
(2) RTO = Referenced to Output.
SCM5B
ORDERINGINFORMATION
MODEL INPUTRANGE OUTPUTRANGE
OM5-IFI-500-C 0 to 500Hz 0V to +5V
OM5-IFI-1K-C 0 to 1kHz 0V to +5V
OM5-IFI-3K-C 0 to 3kHz 0V to +5V
OM5-IFI-5K-C 0 to 5kHz 0V to +5V
OM5-IFI-10K-C 0 to 10kHz 0V to +5V
OM5-IFI-25K-C 0 to 25kHz 0V to +5V
OM5-IFI-50K-C 0 to 50kHz 0V to +5V
OM5-IFI-100K-C 0 to 100kHz 0V to +5V

30
OM5-LTC
Linearized Thermocouple Input Modules
FEATURES
●INTERFACES TO TYPES J, K, T, E, R, S, N, AND B
THERMOCOUPLES
●LINEARIZES THERMOCOUPLE SIGNAL
●HIGH LEVEL VOLTAGE OUTPUTS
●1500Vrms TRANSFORMER ISOLATION
● ANSI/IEEE C37.90.1-1989 TRANSIENT PROTECTION
●INPUT PROTECTED TO 240VAC CONTINUOUS
●160dB CMR
●95dB NMR AT 60Hz, 90dB at 50Hz
●±1µV/°C DRIFT
● CSA CERTIFIED, FM APPROVED, CE COMPLIANT
●MIX AND MATCH OM5 TYPES ON BACKPANEL
DESCRIPTION
Each OM5-LTC thermocouple input module provides a single channel of
thermocouple input which is filtered, isolated, amplified, linearized and
converted to a high level analog voltage output (Figure 1). This voltage
output is logic-switch controlled, allowing these modules to share a
common analog bus without the requirement of external multiplexers.
The OM5-LTC modules are designed with a completely isolated computer
side circuit which can be floated to ±50V from Power Common, pin 16.
This complete isolation means that no connection is required between I/O
Common and Power Common for proper operation of the output switch. If
desired, the output switch can be turned on continuously by simply
connecting pin 22, the Read-Enable pin to I/O Common, pin 19.
The OM5-LTC can interface to eight industry standard thermocouple types:
J, K, T, E, R, S, N, and B. Its corresponding output signal operates over a
0V to +5V range. Each module is cold-junction compensated to correct for
parasitic thermocouples formed by the thermocouple wire and screw
terminals on the mounting backpanel. Upscale open thermocouple detect
is provided by an internal pull-up resistor. Downscale indication can be
implemented by installing an external 47MΩresistor, ±20% tolerance,
between screw terminals 1 and 3 on the OM5-BP backpanels.
Signal filtering is accomplished with a six-pole filter which provides 95dB
of normal-mode-rejection at 60Hz and 90dB at 50Hz. Two poles of this filter
are on the field side of the isolation barrier, and the other four are on the
computer side.
After the initial field-side filtering, the input signal is chopped by a
proprietary chopper circuit. Isolation is provided by transformer coupling,
again using a proprietary technique to suppress transmission of common
mode spikes or surges. The module is powered from +5VDC, ±5%.
A special input circuit provides protection against accidental connection of
power-line voltages up to 240VAC.
FIGURE 1. OM5-LTC Block Diagram.
–V
LPF
LPF
+In
–In
–EXC
Backpanel
Term Block
1
2
6
5
3
Surge
Suppression
and
Protection +V
Isolated
Field-Side
Power
Isolated
Computer-Side
Power
V
OUT
20
19
22
I/O Common
RD EN\
4
3
2
1
+EXC
–V
+V
4
Thermocouple
Precision
Reference
CJC
Temp
Sensor
+2.5V
Linearizer
100MΩ
Power
Oscillator
+5V
17
16 Power Common
Isochopper™
Amplifier
Pat Pending
NC

31
SPECIFICATIONS Typical at TA= +25°C and +5V power.
Module OM5-LTC
Input Range –0.1V to +0.5V
Input Bias Current –25nA
Input Resistance
Normal 50MΩ
Power Off 40kΩ
Overload 40kΩ
Input Protection
Continuous 240Vrms max
Transient ANSI/IEEE C37.90.1-1989
CMV, Input to Output
Continuous 1500Vrms max
Transient ANSI/IEEE C37.90.1-1989
CMR (50Hz or 60Hz) 160dB
NMR 95dB at 60Hz, 90dB at 50Hz
Accuracy See Ordering Information
Stability
Input Offset ±1µV/°C(1)
Output Offset ±20µV/°C
Gain ±25ppm/°C
Noise
Input, 0.1 to 10Hz 0.2µVrms
Output, 100kHz 300µVp-p, 150µVrms
Bandwidth, –3dB 4Hz
Response Time, 90% Span 0.2s
Output Range 0V to +5V
Output Resistance 50Ω
Output Protection Continuous Short to Ground
Output Selection Time 6µs at Cload = 0 to 2000pF
(to ±1mV of VOUT )
Output Current Limit +8mA
Output Enable Control
Max Logic “0” +0.8V
Min Logic “1” +2.4V
Max Logic “1” +36V
Input Current, “0”, “1” 0.5µA
Open Input Response Upscale
Open Input Detection Time 10s
Cold Junction Compensation
Accuracy, 25°C±0.25°C
Accuracy, +5°C to +45°C±0.5°C
Accuracy, –40°C to +85°C±1.25°C
Power Supply Voltage +5VDC ±5%
Power Supply Current 30mA
Power Supply Sensitivity ±2µV/% RTI(2)
Mechanical Dimensions 2.28" x 2.26" x 0.6"
(58mm x 57mm x 15mm)
Environmental
Operating Temp. Range –40°C to +85°C
Storage Temp. Range –40°C to +85°C
Relative Humidity 0 to 95% Noncondensing
Emissions EN50081-1, ISM Group 1, Class A (Radiated, Conducted)
Immunity EN50082-1, ISM Group 1, Class A (ESD, RF, EFT)
ORDERING
INFORMATION
NOTES: (1) This is equivalent to °C as follows:
Type J 0.020 °C/°C, Types K, T 0.025°C/°C,
Type E 0.016°C/°C, Types R, S 0.168°C/°C,
Type N 0.037°C/°C, Type C 0.072°C/°C.
(2) Referenced to input.
MODEL TYPE INPUT RANGE OUTPUT RANGE ACCURACY†
OM5-LTC-J1-C Type J 0°C to +760°C (+32°F to +1400°F) 0V to +5V ±0.08% ±0.61°C
OM5-LTC-J2-C Type J -100°C to +300°C (-148°F to +572°F) 0V to +5V ±0.08% ±0.32°C
OM5-LTC-J3-C Type J 0°C to +500°C (+32°F to 932°F) 0V to +5V ±0.07% ±0.36°C
OM5-LTC-J4-C Type J -100°C to +760°C (-148°F to +1400°F) 0V to +5V ±0.08% ±0.70°C
OM5-LTC-K1-C Type K 0°C to +1000°C (+32°F to +1832°F) 0V to +5V ±0.08% ±0.80°C
OM5-LTC-K2-C Type K 0°C to +500°C (+32°F to +932°F) 0V to +5V ±0.08% ±0.38°C
OM5-LTC-K3-C Type K -100°C to +1350°C (-148°F to +2462°F) 0V to +5V ±0.08% ±1.2°C
OM5-LTC-T1-C Type T -100°C to +400°C (-148°F to +752°F) 0V to +5V ±0.16% ±0.80°C
OM5-LTC-T2-C Type T 0°C to +200°C (+32°F to +392°F) 0V to +5V ±0.13% ±0.25°C
OM5-LTC-E-C Type E 0°C to +1000°C (+32°F to +1832°F) 0V to +5V ±0.10% ±1.0°C
OM5-LTC-R-C Type R +500°C to +1750°C (+932°F to +3182°F) 0V to +5V ±0.10% ±1.3°C
OM5-LTC-S-C Type S +500°C to +1750°C (+932°F to +3182°F) 0V to +5V ±0.10% ±1.3°C
OM5-LTC-B-C Type B +500°C to +1800°C (+932°F to +3272°F) 0V to +5V ±0.15% ±2.0°C
†Includes conformity,
hysteresis and
repeatability. Does not
include CJC accuracy.

32
FEATURES
●ACCEPTS HIGH LEVEL VOLTAGE INPUTS TO ±10V
●PROVIDES HIGH LEVEL VOLTAGE OUTPUTS TO ±10V
●1500 VOLT TRANSFORMER ISOLATION
●ANSI/IEEE C37.90.1e-1989 TRANSIENT PROTECTION
●5 POLES OF FILTERING
●110dB CMR
●400Hz SIGNAL BANDWIDTH
●±0.05% ACCURACY
●±0.02% LINEARITY
●MIX AND MATCH OM5 TYPES ON BACKPANEL
●CSA CERTIFIED, FM APPROVED, CE COMPLIANT
DESCRIPTION
Each OM5-AV voltage output module provides a single channel of analog
output. The track-and-hold circuit in the input stage can be operated in a hold
mode where one DAC can supply many output modules, or a track mode
whereone DAC is dedicatedtoeach module. In additiontothe track-and-hold
circuit, each module provides signal buffering, isolation, filtering, and
conversion to a high level voltage output.
Setting of the track or hold mode is controlled by the logic state of WR EN\,
module pin 23. When pin 23 is low, the track mode is enabled. If pin 23 is
open or high, the hold mode is enabled. The module is designed with a
completely isolated computer side circuit which can be floated to ±50V from
Power Common, pin 16. This complete isolation means that no connection
is required between I/O Common and Power Common for proper operation
of the track and hold circuit. For a low state, simply connect pin 23, the Write-
Enable pin, to I/O Common, pin 19.
The OM5-BP-MUX-C backpanels allow host computer control of the WR EN\
control line, which allows multiplexing of one host DAC to up to 64 OM5-AV
output modules. During power up, the output remains 0V output for 100ms,
which allows the track-and-hold circuit to be initialized.
FIGURE 1. OM5-AV Block Diagram.
OM5-AV
Voltage Output Modules
+Out
–Out
R
LOAD
–EXC
Backpanel
Term Block
1
2
NC
4
6
5
3
Surge
Suppression
and
Protection
Isolated
Field-Side
Power
Track
&
Hold
4
3
2
1
+EXC
–V+V
Power
Oscillator
Isolated
Computer-Side
Power
V
IN
18
23
I/O Common
WR EN\
+5V
Power Common
Isolation Barrier
19
Range
Select
NC 17
16
NC
NC

33
Module OM5-AV
Input Voltage Range ±5V, 0 to +5V, ±10V, 0 to +10V
Input Voltage Maximum ±36V (no damage)
Input Resistance 50MΩ
Output Voltage Range ±5V, 0 to +5V, ±10V, 0 to +10V
Over Range Capability 5% @ 10V output
Output Drive 50mA max
Output Resistance 0.5Ω
Output I Under Fault, Max 75mA
Output Protection
Transient ANSI/IEEE C37.90.1-1989
CMV, Output to Input
Continuous 1500Vrms max
Transient ANSI/IEEE C37.90.1-1989
CMR (50 or 60Hz) 110dB
NMR (–3dB at 400Hz) 100dB per Decade above 400Hz
Accuracy(1) ±0.05% span (0-5mA load)
Nonlinearity ±0.02% span
Stability
Zero ±25ppm/°C
Span ±20ppm/°C
Noise
Output Ripple, 1kHz bandwidth 2mVp-p
Bandwidth, -3dB 400Hz
Sample and Hold
Output Droop Rate 0.2% Span/s
Acquisition Time 50µs
Track-and-Hold Enable Control
Max Logic “0” +0.8V
Min Logic “1” +2.4V
Max Logic “1” +36V
Input Current, “0” 0.5µA
Power Supply Voltage +5VDC ±5%
Power Supply Current 350mA Full load, 135mA No load
Power Supply Sensitivity ±12.5ppm/%
Mechanical Dimensions 2.28" x 2.26" x 0.60" (58mm x 57mm x 15mm)
Environmental
Operating Temp. Range -40°C to +85°C
Storage Temp. Range -40°C to +85°C
Relative Humidity 0 to 95% noncondensing
RFI Susceptibility ±0.5% Span error at 400MHz, 5W, 3ft
Emissions EN50081-1, ISM Group 1, Class A (Radiated, Conducted)
Immunity EN50082-1, ISM Group 1, Class A (ESD, RF, EFT)
SPECIFICATIONS Typical at TA= +25C and +5V Power
ORDERINGINFORMATION
MODEL INPUT RANGE OUTPUT RANGE
OM5-AV-1-C 0V to +5V -5V to +5V
OM5-AV-2-C -5V to +5V -5V to +5V
OM5-AV-3-C -5V to +5V 0V to +5V
OM5-AV-4-C 0V to +10V -10V to +10V
OM5-AV-5-C -10V to +10V -10V to +10V
OM5-AV-6-C -10V to +10V 0V to +10V
OM5-AV-7-C -5V to +5V -10V to +10V
NOTES: (1) Includes nonlinearity, hysteresis and repeatability.

34
number 50865-5. The captive nut for the 3mm mounting screw can be
obtained from PEM (Penn Engineering and Manufacturing), part number
KFS2-M3.
The following mechanical drawing is useful if designing circuit boards to
mount the OM5 modules. Many sockets are available which accept the
mounting pins. As an example, AMP Inc. provides a socket with part
OM5
Module Dimensions and Pinouts
2.255" (57.3mm)
[2.260" max (57.4mm)] 0.585" (14.9mm)
[0.590" max (15.0mm)]
2.270" (57.7mm)
[2.275" max (57.8mm)]
0.095" (2.4mm)
0.145" (3.7mm)
0.345" (8.8mm)
0.20" (5.1mm)
0.375" (9.5mm)
1.175" (29.8mm)
1.650" (41.9mm)
Top
Side
Bottom
2.025" (51.4mm)
1.650" (41.9mm)
1.175" (29.8mm)
0.900" (22.9mm)
0.375" (9.5mm)
0.0750" (1.9mm)
0
0.345" (8.8mm)
0.150" (3.8mm)
Pin Diameter = 0.040" (1.02mm)
NOTES: (1) All dimensions are “Typical” unless otherwise noted.
(2) Mounting pin plating is 20µin. gold.
2322
WR EN\
Reserved
I/O Common
+5V
1716
RD EN\
V
Power Common
OUT
V
IN
56
–In
–EXC
–SEN
12
+In
+EXC
+SEN
23
22 WR EN\
Reserved
I/O Common
+5V
17
16
RD EN\
V
Power Common
OUT
V
IN
5
6
–In
–EXC
–SEN
1
2
+In
+EXC
Top View Bottom View
+SEN

35
Accessories
for OM5 Analog Modules
FEATURES
●SINGLE, DUAL, 8-, AND 16-POSITION BACKPANELS
●DIN RAIL MOUNT BACKPANELS
●19-INCH MOUNTING RACK FOR BACKPANELS
●MULTIPLEXED AND NON-MULTIPLEXED BACKPANELS
●INTERFACE CABLES
●MODULE EVALUATION BOARD
●CABLE-TO-SCREW-TERMINAL INTERFACE BOARD
OM5-BP-16-C 16 POSITION ANALOG I/O BACKPANEL, NON-MULTIPLEXED
FIGURE 1. OM5-BP-16-C Analog I/O Backpanel Dimensions.
SCM5B
SPECIFICATIONS
Operating Temperature: –40°C to +85°C
95% relative humidity, non-condensing
Interface Connector:
Field High Density Screw Clamp, 14 AWG Max
Logic 26-pin, male header connector
DESCRIPTION
The OM5-BP-16-C 16 channel backpanel (Figure 1) can accept any of the
OM5 analog modules in any mixture. It can be mounted on the OMX-1363-
C 19-inch metal rack. The OM5-BP-16-C has 16 non-addressable analog I/
O signal channels which provides each module with it’s own analog bus. The
module output switch is continuously “on” when using this backpanel and all
sixteen module outputs are simultaneously accessible to high-speed data
acquisition (ADC) boards. A set of inter-channel bridge jumpers permits
connecting an input module’s output to an output module’s input, providing
two levels of isolation. A temperature sensor is mounted on each channel to
provide cold junction compensation for thermocouple input modules (See
Figure 2 for schematic). Field connections are terminated with four screw
terminals at each module site. Use system interface cable OMX-1315-XX-
C for connection to the host system.
12345678910111213141516
17.4" (442.0mm)
17.1" (434.3mm)
11.3" (287.0mm)
7.6" (193.0mm)
3.9" (99.1mm)
0.15"
(3.8mm)
1.275"
(32.4mm)
26 Conductor Male Pin
Connectors P1, P2(1)
3.47"
(88.1mm)
3.05"
(77.5mm)
Channel
2.27"
(57.7mm)
0.08"
(2.0mm)
0.75" (19.1mm)
0.093"
(2.4mm)
0.14" (3.6mm)
inside diameter
Pin 1
Pin 2
Pin 2
Pin 1
E3 JP15
P2P1
JP1
E2
E1
Inter-channel
Bridge Jumpers
+5VDC Supply Sockets for Current Conversion Resistors, OMX-1362-C
OMX-CJC-C
Cold Junction
Compensation Circuit
10.32 X 0.40
Ground Lug, Including
Nut and Lockwasher
NOTES:
1. Connector is Berg 65863-075 or equivalent.
Mating Connector is Amp 49958-6 or equivalent.
Connectors P1 and P2 are wired in parallel for “daisy chaining” up to 4 boards.
Swaged Standoff
Thru Hole 0.15" (3.8mm) Dia.
J1 J2 J3 J4

36
FIGURE 2. OM5-BP-16-C Schematic.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
6 4 2
5 3 1
–EXC +EXC–In +In
TB1
TB17
PCOM
LED
+In +EXC +SEN
OMX-1362-C
OMX-CJC-C
–In
–EXC –SEN
Channel 1
1234
Fuse (4A)
F1
PCOM
+5
+5
DZ1
5.6V
PCOM
4 Amps
Jumper
J3
Jumper
J1
Jumper
J2
Signal Ground
and Grounding Bolt
R
1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
1 9
10
2 3
11 12
4 5
13 14
6 7
15 16
8
C
hannel
C
hannel
ACOM
C
hannel
C
hannel
ACOM
C
hannel
C
hannel
ACOM
C
hannel
C
hannel
ACOM
C
hannel
C
hannel
ACOM
C
hannel
C
hannel
ACOM
C
hannel
C
hannel
ACOM
C
hannel
C
hannel
ACOM
Sense
P2 P1
1 3 5 7 9
HD10
2 4 6 8 10
JP1 JP2 JP3 JP4 JP5
E1
I/O 3 I/O 4 I/O 5 I/O 6
I/O 1 I/O 2
1 3 5 7 9
HD10
2 4 6 8 10
JP11 JP12 JP13 JP14 JP15
E3
I/O 12 I/O 13 I/O 14 I/O 15
1 3 5 7 9
HD10
2 4 6 8 10
JP6 JP7 JP8 JP9 JP10
E2
I/O 7 I/O 8 I/O 9 I/O 10 I/O 11
Jumper
J4
22 20 18 16 6 4 2
5 3 1
23 21 19 17
PCOM
I/O COM
–EXC +EXC–In +In
+5
TB16
RD EN\ V
OUT
V
IN
+In +EXC +SEN
OMX-1362-C
–In
–EXC –SEN
Channel 16
WR EN\
NC
I/O COM
OP16
1234
I/O 16
NOTES: 1. J1, J3, J4 and R
1
are factory installed.
3. Resistors OMX-1362-C are optional I/V conversion resistors for current inputs, not factory installed.
2. OMX-CJC-C are CJC temperature sensors.
22 20 18 16
23 21 19 17
PCOM
+5
RD EN\ V
OUT
V
IN
WR EN\
NC
I/O COM
OP1
OMX-CJC-C

37
ELECTRICAL
P1 AND P2 CONNECTOR
Connection to the host system is made at connectors P1 and P2. These
connectors are electrically equivalent. Two connectors are provided to allow
both analog input and analog output from host systems having individual
input and output connectors.
ADJACENT CHANNEL JUMPERS
Adjacent channels may be connected together to provide an isolated output
signal from an isolated input module, providing two levels of 1500V
isolation. This capability is provided with the 15 jumpers labeled JP1
through JP15 on headers E1, E2, and E3. A simplified drawing of the OM5-
BP-16-C schematic for Channel 1 through 4 is shown in Figure 3.
Example: Assume an OM5-IMV input module is installed in Channel 1
position and an OM5-IVI output module is installed in Channel 2 position.
IfJP1 is installed, the outputof Channel 1 is connected to the input of Channel
2, which provides two levels of 1500V isolation.
GROUNDING
Figure 4 details the optional ground jumper configuration available on the
OM5-BP-16-C backpanel. Jumpers J1, J3, and J4 are factory installed.
Jumper J1 connects the AGND shield wires (pins 3, 6, 9, 12, 15, 18, 21, and
24) to the backpanel signal ground. This provides a ground connection
between the host system and backpanel. Jumper J1 is required if output
modules are used, or if there is no high impedance sense input (input low of
a differential or pseudo-differential system) on the host measurement sys-
tem.
Jumper J3 connects the SENSE line (pin 25) to the backpanel signal ground.
If the host system has the capability, this allows measuring the OM5-BP-16-
C ground potential.
For proper operation of the output switch or track-and-hold circuit when
using the OM5 backpanels, a current path must exist between the host control
logic power common and module I/O Common (module pin 19). This path
can be established on the OM5-BP-16-C via jumper J4. If this connection
exists elsewhere in the system, jumper J4 should be removed since possible
ground loops could exist. Other connections of power ground and signal
FIGURE 3. OM5-BP-16-C Adjacent Channel Jumpers.
ground usually occur at the A/D or D/A converter of the host measurement
system.
If the connection of power common and AGND shield wires exists in the host
measurement system, an optional resistive connection between AGND and
the backpanel signal ground can be made via R1. R1can be as large as 10K
ohms; 100 ohms is a recommended value. Jumper J2 can be used to connect
the SENSE line to R1when this ground configuration is used.
Forfull protection against large electrical disturbances on the field-side of the
OM5 modules, a #10-32 ground stud is provided on the backpanel. An
electrical connection between this ground stud and system ground should be
provided with a large gauge wire of the shortest possible length. When this
connection is made, a possible ground loop could result through the AGND
shield wires and backpanel signal ground. If the application involves only
input modules and a differential input is used by the host measurement
system, J1 should be removed. Remember that J1 is required if output
modules are used or if the host system does not have differential inputs.
FIGURE 4. OM5-BP-16-C Grounding Diagram.
POWER
The OM5-BP-16-C backpanel requires external +5VDC ±5% power. The
chassis mounted OMX-976-C power supplies have adequate capacity to
power any combination of modules.
FUSING
The OM5-BP-16-C backpanel power is fuse protected through F1. This is a
Littlefuse type 252004, 4 amp fuse. Zener diode DZ1 provides extra
protection by clamping the input power voltage to +5.6V. If the input supply
voltage connection is reversed, this zener diode will be forward biased and
fuse F1 will be blown.
P1
1
5
7
11
13
P2
V
OUT
20
V
IN
18
CH 1
V
OUT
20
V
IN
18
CH 2
20
18
CH 3
20
18
CH 4
12 34 56
JP4
HD10, E1
JP1 JP2 JP3
V
OUT
V
IN
V
OUT
V
IN
SCM5B
P1
3
6
9
12
15
P2
J3
19
OM5 Module
18
21
24
25
J1
J2
Sense
AGND
Signal Ground
and
Grounding Bolt
R1
J4
Power Common
16I/O COM PWR COM

38
DESCRIPTION
The OM5-BP-16-MUX-C 16 channel backpanel (Figure 5) can accept any
of the OM5 analog modules in any mixture. It can be mounted on the
OMX-1363-C 19-inch metal rack. The OM5-BP-16-MUX-C has two
analog buses; one for analog input and one for analog output. This two-
bus configuration takes advantage of the switch controlled outputs on the
input modules and the track-and-hold inputs on the output modules. A
temperature sensor is mounted on each channel to provide cold junction
compensation for thermocouple input modules (See Figure 6 for
schematic). Field connections are terminated with four screw terminals at
each module site. Up to four OM5-BP-16-MUX-C backpanels may be
daisy-chained. Use OMX-CAB-01-C cable for daisy chaining and OMX-
1315-XX-C cable for connecting to host computer.
SPECIFICATIONS
Operating Temperature: –40°C to +85°C
95% relative humidity, non-condensing
Interface Connector:
Field High Density Screw Clamp, 14 AWG Max
Logic 26-pin, male header connector
Address Input Logic Levels:
Max Logic “0” 0.8V
Min Logic “1” 2.0V
IIInput Current, “0” or “1” 0.1µA max at 25°C
1.0µA max –25°C to +85°C
RD EN\ or WR EN\ Signal Delay
from Connector P1 to Channels 1-16
Standalone (address 0-15) 51ns at 25°C
64ns at –25°C to +85°C
Expanded (address 16-63) 100ns at 25°C
126ns at –25°C to +85°C
FIGURE 5. OM5-BP-16-MUX-C Analog I/O Backpanel.
OM5-BP-16-MUX-C 16 POSITION ANALOG I/O BACKPANEL, MULTIPLEXED
12345678910111213141516
17.4" (442.0mm)
17.1" (434.3mm)
11.3" (287.0mm)
7.6" (193.0mm)
3.9" (99.1mm)
0.15"
(3.8mm)
1.275"
(32.4mm)
3.47"
(88.1mm)
3.05"
(77.5mm)
0.08"
(2.0mm)
0.093"
(2.4mm)
0.14" (3.6mm)
inside diameter
Channel
2.27"
(57.7mm)
Pin 1
Pin 2
0.75" (19.1mm)
E2
E1
P1
+5VDC Supply Write Address
Selection Jumper
Read Address
Selection Jumper
Sockets for Current Conversion Resistors, OMX-1362-C
OMX-CJC-C
Cold Junction
Compensation Circuit
10.32 X 0.40
Ground Lug, Including
Nut and Lockwasher
26 Conductor Male
Pin Connector P1(1)
NOTES:
1. Connector is Berg 65863-075 or equivalent.
Mating Connector is Amp 49958-6 or equivalent.
Swaged Standoff
Thru Hole 0.15" (3.8mm) Dia.
4
3
2
1
0