Omega National Products Baxter Arched User manual

Baxter
Arched Range Hood
Arched Range Hood
Baxter Arched Range HoodBaxter
Important Notes
• Always read the instructions completely and carefully before beginning assembly.
• Remove and check contents for damage and/or missing parts. Keep the original
cartons and packing materials, which are required for any authorized adjustment by
our dealers.
• These instructions are for reference only. Make sure installation procedures comply
with all applicable building codes in your area.
Parts List
Form OME-087, 09/2012
©Omega National Products
1 ea.- Mounting Board
2 ea.- Mounting Brackets
1 ea.- Range Hood Liner
1 ea.- Range Hood
1 ea.- Shelf
1 ea.- Hardware Pack
10-0570-1

Step 1:
Install 6 each “T” nuts into the back of the
mounting board into the counterbored holes.
Hammer them flush to the surface (See figure
1).
Step 2:
Draw a level line on the wall centered where
the Range Hood is to go 6 9/16” above where
the bottom of the Range Hood will be (See
figure 2). A distance of 24-30 inches from the
stove top to the wood hood is recommended.
Check local building codes and regulations for
final determination.
Step 3:
Screw the mounting plate to the wall match-
ing the bottom of the mounting board to the
line on the wall. Make sure to hit at least two
studs and to use at least 6 screws of sufficient
size and length for the application (See figure
3).
Warning
: Failure to fasten this panel to studs
or using the wrong screws may cause a failure
of the mounting system and possible injury.
Assembly Instructions
Assembly Instructions
Figure 1
Figure 2
Figure 3
Step 4:
Start 6 each 10-24 x 3/4” screws into the “T”
nuts that were previously installed (See figure
4).
Figure 4
Form OME-087, 09/2012
©Omega National Products
10-0570-2

Step 5:
Insert the Omega National Products Blower
(sold Separately) into the liner from below.
Using the 4 holes in the side of the blower
attach to the liner with 4 each 8-32 x 1/2”
screws and square nuts (See figure 5).
Figure 5
Step 6:
Fasten the Metal Mounting brackets to the
liner with 4 each 10-24 x 3/4” screws and nuts.
Only hand tighten these at this time (See fig-
ure 6).
Figure 6
Step 7:
Using help if necessary, lift the liner, Blower
and mounting bracket assembly into position
and hang on the screws extending from the
mounting plate. Make sure the brackets are
firmly seated into the key hole slot and then
tighten all the screws (See figure 7).
Figure 7
Step 8:
Make all ventilation and electrical connections
at this time. These must be done in accor-
dance to all applicable building codes and
requirements in your area.
Form OME-087, 09/2012
©Omega National Products
10-0570-3

Step 10:
Carefully position the Wood Range Hood
against the wall and slide down onto the
wedges. The liner should be slightly above
the wood (See figure 10).
Rangehood Wedge
Mounting Board
Wall
Figure 10
Step 11:
Fasten the metal liner to the Wood Range
Hood at this time using 4 each #8 x 1/2” pan
head screws (See figure 11).
Form OME-087, 09/2012
©Omega National Products
1010 Rowe St. Elkhart, IN 46516
[phone] Fax [phone]
www.omeganationalproducts.com
#8 x 1/2" Pan Head Screws
Figure 11
Step 9:
Remove the screws from the
shelf and use
those same screws to attach it using the
pre-
drilled holes on the fro
nt of the
Wood Range
Hood (See figure 9).
Figure 9
10-0570-4