Omega Research & Development Omegalink User manual

5-BUTTON LED 2-WAY
QUICK START OPERATION GUIDE
5-BUTTON LED 2-WAY
QUICK START OPERATION GUIDE
REPLACING YOUR REMOTE BATTERY
STEPS REMOTE PART# BATTERY (QTY)
1) Find the part # on the back of the remote to identify the battery.
2) Locate the relief in case near the key chain and separate the case halves to
access & replace the batteries.
552 CR2450 (1)
551 CR2032 (1)
SECURITY, KEYLESS ENTRY, & CONVENIENCE FUNCTIONS
FUNCTION BUTTON(S) REMOTE CONFIRMATION NOTE
Lock & Arm* Beep + LED flash The doors will lock.
Unlock & Disarm* Beep + LED flash The doors will unlock.
Silent Lock* x1 Single Beep The doors will lock with no audible confirmation.
Silent Unlock* x 2 Double Beep Perform within 1 second. The doors will unlock with no
audible confirmation.
Trunk/Hatch Release for 3 sec. Beep + LED flash Some systems may also unlock the doors.
Panic* or for 3 sec. Alarm Alert + All LEDs Flash The system will sound the horn/siren for Panic Mode.
Register today at www.CarAlarm.com
For warranty info & Download the latest operation guide.
Copyright 2019 Omega Research & Development Technologies, Inc. OC_55208_20190808
/c/omegard
/omegard
Problems? Questions? Contact Customer Service:
800-554-4053 (toll free) | [phone] (outside USA)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna., Increase the separation
between the equipment and receiver., Connect the equipment into an outlet on a circuit different from that to which the receiver is connected., Consult the dealer or an experienced radio/TV technician for help.,
Warning! Changes or modications made to this equipment not expressly approved by the part responsible for compliance could void the use’s authority to operate the equipment
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such modications could void the user’s authority to operate the equipment.
14
PROGRAMMING REMOTES TO THE SYSTEM
Remote programming is dependant on the system being controlled. Please consult your dealer or the system guide for the proper
programming instructions.
Visit www.CarAlarm.com today
To Download the latest operation guide and learn more about system upgrades & other features!
Scan to register
& download the
latest operation
guide at
CarAlarm.com!

5-BUTTON LED 2-WAY
QUICK START OPERATION GUIDE
5-BUTTON LED 2-WAY
QUICK START OPERATION GUIDE
OTHER CONTROLLER FUNCTIONS
FUNCTION BUTTON(S) CONFIRMATION NOTE
Remote Valet Hold & for
3 sec + LED flash
This disables remote start and the security system. The status LED will turn on. Repeat this process or press valet
button once to exit valet mode.
Multi-Car Hold & for
3 sec
+ LED flash
1x =car 1/2x = car 2
The LED flash upon any button press will indicate current car setting. Repeat to return to car 1.
1 flash = car 1 / 2 flash = car 2
Button Lock Hold & for
3 sec & LED will flash 4x When button lock is on the remote will not transmit. When any button is pressed the correspnidng LED will flash rapidly
uopn button press.
, Beep + LED flash 1x AUX1 - Write function in “FUNCTION” column
x 2 , Beep + LED flash 2x AUX2 - Write function in “FUNCTION” column
x 3 , Beep + LED flash 3x AUX3 - Write function in “FUNCTION” column
& Beep + & LED flash AUX4 - Write function in “FUNCTION” column
3
*All functions are dependent upon vehicle & system availability. Consult your installer to conrm feature availability.
2
*All functions are dependent upon vehicle & system availability. Consult your installer to conrm feature availability.
Status LED
Valet / Programming Button
Status LED
REMOTE START FUNCTIONS
FUNCTION BUTTON(S) CONFIRMATION NOTE
Engine Start/Stop x 2 Melody + LED flash Upon sucessful start, the remote will beep 4x and the Start LED will flash every 5 seconds during the programmed
runtime. Take Over*: Enter the vehicle and turn ignition key ‘ON’ then press the brake pedal.
Run Time Extender* Beep + LED flash The runtime will reset (only allowed once per remote start cycle).
Auto Start Mode* & Beep + & LED flash
1 beep for Auto Start Mode On / 2 beeps for Auto Start Mode Off.
Remote starts your vehicle every 2, 3, or 4 hours (programmable) or upon temperature threshold.
WINDOW-MOUNT ANTENNA/RECEIVER