Omega Research & Development Excalibur User manual

1-Button 2-Way LED Remote Start Systems
QUICK START OPERATION GUIDE
1-Button 2-Way LED Remote Start Systems
QUICK START OPERATION GUIDE
REPLACING YOUR REMOTE BATTERY
STEPS REMOTE PART# BATTERY (QTY)
1) Find the part # on the back of the remote to identify the battery type.
2) Remove the screw from the back of the remote.
3) Gently pry the case halves apart to access & replace the batteries.
1110 CR2025 (2)
1111 CR2032 (1)
SECURITY, KEYLESS ENTRY, & CONVENIENCE FUNCTIONS
FUNCTION BUTTON(S) LED CONFIRMATION NOTE
Lock & Arm1For 1 Sec. LED Flash + 1 Beep Security enabled systems will flash the status LED.
Repeat to Unlock/Disarm
Unlock & Disarm1For 1 Sec. LED Flash + 2 Beeps Repeat to Lock/Arm
Engine Start/Stop x 2
LED Flash + Melody
Engine Runtime Flashes:
4x = 76-100% remaining
3x = 51-75% remaining
2x = 26-50% remaining
1x = 1-25% remaining
Activation is programmable (contact installer).
Key Take Over: Turn ignition key ‘ON’ (not start), press
brake pedal.
Run Time Extender2LED runtime flashes will
start over The system will restart the internal run timer.
Register today at www.CarAlarm.com
To activate/view your warranty & Download a complete operation guide.
Copyright 2019 Omega Research & Development Technologies, Inc. QOM_1BUTLED2WAY_20190829
Scan to register
& download the
full operation
guide at
CarAlarm.com!
/c/omegard/omegard
Problems? Questions?
Contact Customer Service:
800-554-4053 (toll free) |
[phone] (outside USA)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna., Increase the separation
between the equipment and receiver., Connect the equipment into an outlet on a circuit different from that to which the receiver is connected., Consult the dealer or an experienced radio/TV technician for help.,
Warning! Changes or modifi cations made to this equipment not expressly approved by the part responsible for compliance could void the use’s authority to operate the equipment
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifi cations to this equipment. Such modifi cations could void the user’s authority to operate the equipment.
Remote Start/Security System Model:
(Installer, write system model above)
14
PROGRAMMING REMOTES TO THE SYSTEM (UP TO 4)
BEFORE YOU BEGIN: Have all remotes for the system at hand.
1) Turn the ignition key “ON” (do not start).
2) Press the valet button 5 times within 5 seconds of step 1.
- The siren/horn may briefly sound
3) Press & release the “lock” button on each transmitter one after the other.
- 1-button models, press the “start” button.
- The siren/horn may chirp once for each transmitter.
- NOTE: When the fi rst remote is learned all previous remotes are erased.
4) Turn the ignition key “OFF”.
- NOTE: The system will exit at any time
after 10 seconds of no activity.
SCAN TO WATCH
HOW-TO VIDEO
Visit www.CarAlarm.com today
To Download your complete operation guide and learn more about system upgrades & other features!
1-Security related functions only available on some models. Consult your installer for more info.
2-These fu-nctions are only available on some remote start models. Consult your installer for more info.

1-Button 2-Way LED Remote Start Systems
QUICK START OPERATION GUIDE
1-Button 2-Way LED Remote Start Systems
QUICK START OPERATION GUIDE
REMOTE START FUNCTIONS
FUNCTION VALET BUTTON NOTE
Pit Stop Mode2Press 2x after Engine Running For
More Than 10 Seconds
(Press 6x for XL mode)
This will leave the engine running for the programmed run time (XL mode runs for 12 hours) so you can take your
keys with you to run errands.
Low Battery & Low/
Hi Temp Auto-Start Ignition Key ON, OFF, Press 2x Auto-start will activate a max of once per 2 hours. See your installer or the full manual for threshold settings.
Valet Mode2Unlock, Hold For 3 Sec. This disables remote start and the security system. The status LED will turn on. Repeat this process or press valet
button once to exit valet mode. TIP: You can also enter valet mode by holding the valet button for 3 seconds!
OTHER 2-WAY CONTROLLER FUNCTIONS
FUNCTION BUTTON(S) LED
CONFIRMATION NOTE
Low Car
Battery Alert - 4 Beeps Alerts when battery level is below 11.5v
for over 30 seconds.
Out Of Range - 4 LED Flashes When command response is not received
2-WAY CONTROLLER OPTIONS
FEATURE PROCEDURE
Beep Volume Hold for 7 seconds. Controller will scroll through:
Melody > Soft Melody > Silent
2
Scan to register
& download the
full operation
guide at
CarAlarm.com!
REMOTE START ERRORS3
CHIRPS/FLASHES VIOLATED ZONE
LED ON System in Valet mode
1 Hood opened
2 Brake pedal pressed
3 Bad tach signal or engine over-rev.
4 BLACK/WHITE wire lost ground
5 3D motion detected while cranking
6 Received engine stop command
7 Alarm was triggered
8 Run time expired
9 Low vehicle battery voltage detected
3
2-These functions are only available on some remote start models. Consult your installer for more info.
TIP: If remote start won’t activate, the system may be in valet mode
(Status LED ON). Press the valet button once to exit.
3-These functions are only available on some remote start models.
If the system fails to remote start or remote start stops unexpectedly,
it will give a long horn/siren chirp followed by a series of short horn/
siren chirps & light flashes. The short chirps/light flashes indicate
the cause of the failure.
MANUAL TRANSMISSION RESERVATION MODE2
This must be performed before you can remote start a manual transmission vehicle to ensure the car is in neutral &
maximum safety. Consult your installer for more information.
1) With the engine running (more than 10 seconds), hold the brake pedal & place the transmission in neutral.
2) Apply the parking brake and release the brake pedal.
3) Send the remote start command via your remote. The remote start should engage
(not crank) and the status LED will begin flashing.
4) Take the ignition key out of the switch (the engine should stay running).
5) Exit the vehicle and lock your doors with the remote. The engine will turn off. Status LEDValet / Programming Button
WINDOW-MOUNT ANTENNA/RECEIVER