Omega BL420 User manual

INSTRUCTION
MANUAL
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE
English
OMGMAN 082009 RevA
www.omegajuicers.comwww.omegajuicers.comEat well, drink well and live well with OmegaEat well, drink well and live well with Omega
BL400 SERIES BLENDER
BL400MAN 122011 Rev A

Electrical Shock Hazard
Plug into a grounded outlet.
Do not remove ground.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can
result in death, fire or electrical shock.
oving Parts!
Always cover the lid on the container when
blending.
Do not put hands, spoons or other utensils in
container when blending.
Failure to follow these instructions can result
in broken bones, cuts or other injuries.
DANGER Electricity
DANGER Risk of Electrical Shock
GENERAL Caution
DANGER Keep Hands Clear
BLENDER SAFETY
WARNING WARNING
FAILURE TO ADHERE TO THESE WARNINGS CAN RESULT IN FIRE,
SERIOUS INJURY, ELECTRICAL SHOCK AND/OR DEATH
Technical Services
For assistance or replacement parts, call
Technical Service
24 Hours a Day, 7 Days a Week at
Toll Free: #1-800-633-3401
I PORTANT: Please adhere to all safety guidelines contained in this manual.
DANGER: You can be seriously injured if you do not follow these intructions.

Specifications 3
Important Safeguards 4
Blender Operation 5
Care and Cleaning 6-7
Control Panel 8
Blade Agitator Assembly 8
Troubleshooting 9
aintanace 10
TABLE OF CONTENTS

Shipping Dimensions:
17.5" W x 10" D x 13.75" H
440mm W x 250mm D x 350mm H
Shipping Weight:
7.5 lb
3.4 kg
Power Requirements:
Volts: 120/220 VAC
Amps: 11.5/6.3 Amp
Hz: 50-60
Container:
64 Oz. / 1800ml
82 Oz. / 2300ml
Specifications
BL420 BL460BL440 BL490

4
I PORTANT SAFEGUARDS
hen using electrical appliances, basic
safety precautions should always be
followed, including the following:
1. Read all the instructions before using the
blender.
2. Plug into a grounded outlet.
3. Do not remove ground.
4. Do not use an adapter.
5. Do not use an extension cord.
6. To protect against risk of electrical shock,
do not put the blender in water or other liq-
uid.
7. Close supervision is necessary when any
appliance is used near children.
8. Unplug from outlet when not in use, before
putting on or taking off parts, and before
cleaning.
9. Avoid contact with moving parts, especially
blades.
10. Do not operate any appliance with a
damaged cord or plug or after the appliance
malfunctions, or is dropped or damaged in
any manner. Return appliance to the nearest
authorized service facility for examination /repair
/electrical or mechanical adjustment, or
contact your distributor.
11. Caution: Keep hands and utensils out of
container while blending to reduce the risk of
severe injury to persons or damage to the
blender. If scraping, folding, etc. is
necessary, turn off and unplug the blender,
and use a rubber spatula only.
12. Warning: Blades are sharp. Handle
carefully.
13. To reduce the personal injury, never place
cutting blades on base without jar properly at-
tached.
14. Screw on locking ring firmly. Injury can
result if moving blades accidentally be-
come exposed.
15. Always operate blender with lid in place.
16. When blending hot liquids, place a hand
towel over the cover. Do not fill blender con-
tainer beyond 2/3 full. Always begin process-
ing at the lowest speed setting. Keep hands,
arms and face away from the feeder cup
opening to prevent possible burns.
17. Do not use outdoors.
18. Do not let cord hang over edge of table
or counter, or touch hot surfaces.
19. Do not leave blender unattended while it
is operating.
20.The use of unapproved attachments
may cause injuries.
21. The capacity can be substantially less
than normal with thick mixtures.
22. Inspect the container assembly daily. Do
not use a broken, chipped or cracked
container. Check cutter for wear, nicks or
broken blades.
23. This appliance is intended for short
period of operation, with a average rated op-
erating time of approximately 3 minutes.
24. This appliance is not intended for
use by persons (including Children) with
reduced physical, sensory or mental ca-
pabilities or lack of experience and
knoledge, unless they have been given
supervision or instruction concerning the
use of the appliance by a person respon-
sible for their safety. Children should be
supervised to ensure they do not play
with the appliance.

BLENDER OPERATION
To operate the blender, proceed as follows
1. For the first time user, wash the container assembly, including the lid, before using it. (Refer
to "Cleaning Instruction") Do not put the container assembly & blender base assembly in the
dishwasher.
2. Place the blender on a dry, clean, level surface,
and be sure it is set to off.
3. Place the container onto the blender base. Make
sure it rests securely on the base.
4. Plug the blender into an electric outlet.
5. Place the ingredients into the container.
6. Place the lid and feeder cap tightly on the container.
7. Set desired speed (High/Low toggle or variable knob) and time (on timer model only).
8. Switch blender on.
PROFESSIONAL BLENDER TIPS
1.Processing hot liquid
mAlways cover the lid and feeder cap before blending hot liquid or mixture.
mUse the feeder cap to add liquids to the container while the unit is running.
mNever stand with your face directly over the container when you are putting ingredient
through the feeder cap.
2.Blending Icy mixtures
mSteps for blending ice:
Pour in liquid, and then add ice.
Place the lid.
Set to desired speed
Chunks of frozen fruit can be added to milk or fruit juice to
produce a sherbet or slush.
Use the feeder cap to add liquids or ingredients to the container
while the unit is running.

6
CLEANING INSTRUCTIONS
Centaur blender container parts are corrosion resistant, sanitary and easily cleaned.
Do not put the container assembly & blender base assembly in the dishwasher.
1. Before first use and after every use, separate container parts from the base.
2. Add cleaning solution to the container. Use washing solution of tepid water (less than
115°F/46°C) and a non-sudsing detergent. Use the recommended amount of detergent.
3. Scrub and flush out the container interior lid and feeder cap to remove food residue. Empty
container.
4. Fill container 1 /4 full with fresh washing solution and place it on the base.
5. Replace the lid on the container and run the blender on high speed for 2 minutes.
6. Repeat step 4 using clean rinse water (95°F/35°C).
7. Wipe down the container, feeder cap, and lid with a soft cloth or sponge, dampened with
fresh washing solution.
8. Wipe the exterior of the base with a damp cloth or sponge. The base contains electrical
components: do not immerse, use a high-pressure washer, or use a dishwasher to clean the
base.
CARING TIPS
To care for your blender, please read the tips as follows:
1. Periodically check all parts before reassembly. As use of damaged or non-recommended
parts could result in a severe personal injury and/or damage to the blender
2. Blades:
If the processing blades are stuck or difficult to turn, DO NOT USE BLENDER (Check by
carefully turning the blades in a counterclockwise direction, where the opposite edges are
sharp. Blades should turn freely.)
3. Container:
If the EASTMAN TRITAN container is cracked, DO NOT USE BLENDER, further use
could result in the container breakage during use.
4. Blender Base:
Never immerse the blender base in water. Unplug unit. The housing can be cleaned with a
damp cloth.
5. Motor:
The motor is permanently lubricated and does not require any additional lubrication.

Caution & Safeguards
1. To protect against risk of electrical shock, do not put motor base in
water or other liquid.
2. Unplug the power cord from the wall outlet when the unit is not
in use, before putting on or taking off parts, and before cleaning other
than washing the container.
3. Never contact moving parts.
4. Do not use outdoors.
5. Do not let the power cord hang over edge of table or counter, or
touch hot surfaces.
6. Keep hands and utensils out of the container while the motor
is running to prevent the possibility of severe personal injury and/or
damage to the unit. A rubber scraper may be used, but only when the
unit is not running.
7. The blade is very sharp and requires carefull handling. Never try to
remove blade while container is sitting on the motor base. Do not op
erate with loose or damaged blades. To reduce the risk of personal in
jury, never place blade assembly on motor base without blender
container properly attached.
8. Always operate with the lid in place.
9. NEVER bang the container against a surface to loosen the ingredi
ents. Remove the container from the base and use a rubber spatula to
remove thick mixtures from the bottom of your container.
10. NEVER shake or rattle a container in use while seated on
the motor base.
11. NEVER remove the container before the machine has come to a
complete stop.
12. NEVER start the motor before the container is in place.
13. Keep children away when the blender is in use.
On most models, the power cord comes equipped with a three-prong
(grounding) plug which mates with a standard three-prong wall outlet
(Figure A). Please use approved 2 prong adapters(Figure B) when a
ground is not available. Do not cut or remove the round grounding prong
from the power cord.

Control Panel
Blade Agitator Assembly
Use caution when handling the blade; it is sharp. Use a soft cloth to grab
the blade when inserting the blade assembly through the container.
Retainer Nut and Blade Removal
•The retainer nut is easily removed using the disassembling tool (DT).
Turn container upside down and insert the disassembling tool on the
holes of the nut. Push the tool counterclockwise to loosen nut (Step 1).
Once loosened, remove by hand.(Disasembly tool sold separately)
•To release the blade use the other end of the DT while grabbing the
gear with backup pliers and turn counterclockwise (Step 2)
Care and Cleaning
otor Base
1. Unplug the power cord.
2. Wipe outside surface with a damp soft cloth or sponge, which has
been rinsed in a mild solution of liquid dish soap and warm water. NEVER
I ERSE OTOR BASE IN WATER OR OTHER LIQUID.
3. Wipe dry with a clean, soft cloth.
Control Panel
Gently wash the front panel with a soft cloth and low pH balance soap,
being careful not to scratch the Display Window.
NOTE: Be sure to wring excess water out of cloth or sponge when cleaning
around the controls, drive socket or any electrical part.
Container
BL420/422 64 z. / 1800ml n/ ff Switch High/Low Switch
BL430/432 82 z. / 2300ml n/ ff Switch High/Low Switch
BL440/442 64 z. / 1800ml ff/Low/High Knob Pulse Switch
BL450/452 82 z. / 2300ml ff/Low/High Knob Pulse Switch
BL460/462 64 z. / 1800ml n/ ff Switch Variable Sped Knob Pulse Switch
BL470/472 82 z. / 2300ml n/ ff Switch Variable Sped Knob Pulse Switch
BL480/482 64 z. / 1800ml n/ ff Switch Variable Speed Knob Timer Knob
BL490/492 82 z. / 2300ml n/ ff Switch Variable Speed Knob Timer Knob
Controls
8

Lid
Separate the lid and plug, then wash in warm soapy water. Rinse clean
under running water and dry. Reassemble before use.
Container
1. To clean: Fill pitcher 1/4 full with warm water and add 2-3 drops of
dish soap. Return container to motor base and firmly positionthe two part
lid. Run machine for 30 seconds. Empty container. Repeat this step.
Troubleshooting
Problem Probable Cause Probable Solution
Loud noise from
the container
•Container blades
do not spin
•Increased vibration
•Leaking from
bottom of container
• Broken or worn drive
socket. Replace drive
socket.
• Check blade assembly
for damaged compo
nents and replace.
• Tighten retainer nut on
the bottom of the
container
achine starts
then shuts off
•otor
•Reset button
•Depress reset button
•Call Omega Customer
Service
achine starts
then shuts off
•Power failure
•Power supply cord
damage
•Check to make sure
there is power to the
machine
•Check the power
supply cord and the
connection to the
power outlet

10
AINTENANCE
Daily
1. Unplug the blender and remove the
container from the base.
2. Inspect the container blades for wear,
nicks, and broken or loose blades. Re-
place if necessary.
eekly
1. Unplug the blender.
2. Inspect the power cord insulation and
power plug for cracks. Refer to "Techni-
cal Service" for repair or replacement.
Quarterly
1. Review the condition of the container
assembly and Mushroom Clutch Set at
least every 90 days.
1. Replace if necessary.
Inspect the blender and its various parts and replace as follows:
Replacement Parts
For replacement parts, call toll free: #1-800-633-3401

Omega Products, Inc · Fort Lauderdale, FL 33331, U.S.A.
Phone:[phone] · Fax:[phone]
www.omegajuicers.com