Omnik Omniksol-WIFIKIT User manual

User Manual V2.4
Omniksol –WIFIKIT User Manual
Omnik New Energy Co., Ltd.

User Manual V2.4
Overview of WIFIKIT Function
Omniksol-WIFIKIT is developed by Omnik as an external communication monitoring device,
which integrates WiFi device for users and provides a wireless monitor function.
By connecting with inverters through RS485 interface, the Kit can receive information from
inverters and realize cascade of inverters. One side It provides wireless function, another
side, it may also use cable to transfer inverter data to the web server.
Users can monitor the runtime status of the device by checking the 4 LEDs on the panel
which indicates Power, RS485, Link and Status respectively.

User Manual V2.4
1
Catalog
1 RS485 Card Install SOP...............................................................................................................................................2
1.1 Disassembly.........................................................................................................................................................2
1.2 Installation ............................................................................................................................................................3
2 Omniksol –WIFIKIT User Manual.................................................................................................................................5
2.1 Unpack .................................................................................................................................................................5
2.2 The installation of data collector...........................................................................................................................5
2.2.1 Wall-mounted installation..................................................................................................................................5
2.2.2 Horizontal data collector installation..................................................................................................................5
2.3 Connection between data collector and inverter...................................................................................................6
2.3.1 The instructions of data collector interface and connection line interface .........................................................6
2.3.2 Steps of connection ..........................................................................................................................................7
2.4 WiFi settings.........................................................................................................................................................8
2.4.1 Wireless network...............................................................................................................................................8
2.4.2 Wired network.................................................................................................................................................12
2.5 Debug.................................................................................................................................................................13
2.6 Register on monitoring website ..........................................................................................................................15
2.6.1 Click Register button to go to registering interface for new account...........................................................16
2.6.2 Fill in user’s information as required........................................................................................................... 16
2.7 Login the PV monitoring system to manage the power station...........................................................................18
2.8 IPhone & iPad application...................................................................................................................................23
3 Contact.......................................................................................................................................................................25

User Manual V2.4
2
1 RS485 Card Install SOP
1.1 Disassembly
Picture 1.1.1
Unscrew the four screws on the interface panel with the screwdriver as shown in Picture
1.1.1 and keep the screws aside.
Picture 1.1.2

User Manual V2.4
3
Picture 1.1.3
Unscrew the two-holed water-proofing connector from the interface panel as shown in
Picture 1.1.2, 1.1.3.
1.2 Installation
Pick out the net cable and the water-proofing connector from the package and follow the
Picture：
A. Put the net cable in from the gap
B. Pput the net cable one after another into the kneck of the interface panel
Picture 1.2.1

User Manual V2.4
4
C. Insert the RS485 card lightly from the position as follow picture
Picture 1.2.2
D. Finish the installation, as Picture 1.2.3：
Picture 1.2.3

User Manual V2.4
5
2 mniksol –WIFIKIT User Manual
2.1 Unpack
After unpacking the box, please check the parts according to the below list. Contact the
manufacturer immediately, should you find any damage, missing or wrong model of the
device or any parts.
Serial
Name
Quantity
Model
A
PV data collector
1
WIFIKIT
B
Power supply adapter
1
FY0502000
C
screw
2
--
D
expanded rubber tube
2
--
E
manual
1
--
2.2 The installation of data collector
2.2.1 Wall-mounted installation
1. Mark two horizontal round holes which distance is 69mm in the selected position
2. Drill two φ6mm holes in the marked position, the depth of the hole is not less than 30mm
3. Punch the expanded rubber tubes into the holes lightly with a rubber hammer
4. Wring two screws into the expanded rubber tubes, the screws head exposed wall about
6cm
5. Hang the PV data collector WIFIKIT on the screws，hold the metal part of the antenna
and rotate the antenna to a wanted position
Picture 2.2.1
2.2.2 Horizontal data collector installation
Lay the data collector on a flat surface
Note1: The protection level of PV data collector WIFIKIT is IP21. It cannot be installed outdoors or in the
Picture 2.1.1

User Manual V2.4
6
conditions of damp, dusty or with corrosive steam. Direct sunlight is also avoided, as well as shock and
pressure defense. In addition, as metal components have effect on the wireless signals, the antenna of
PV data collector (in all direction) should be away from metal components at least 10cm.
Note2: When screw or adjusting the antenna position, please note only the metal part can be screwed,
plastic part cannot be screwed, or the antenna will be damaged. in addition, the unusual installation status
will affect the usage of data collector, more details please refer to the abnormal condition and dispose
during debugging.
2.3 Connection between data collector and inverter
2.3.1 The instructions of data collector interface and connection line interface
Serial
Instructions
A
RS485/422 interface
B
Ethernet
C
Reset
D
Power supply adapter interface
E
Antenna interface
Picture 2.3.1

User Manual V2.4
7
2.3.2 Steps of connection
Both ends of the connecting wire are RJ45 network cable connector，all the line sequence
are T568B.
A. Single inverter connection
1. cut of the power supply of the inverter
2. Insert the network cable into anyone RJ45 port on anyone inverter
3. Let the other network cable connects the network interface of PV data collector
WIFIKIT
4. Connect the power supply adapter to data collector, then insert into the socket
B. Multiple inverter connection
1. Cut of the power supply of the inverter
Pin NO.
RS485
RS422
1
NC
NC
2
NC
NC
3
NC
RX+
4
A
TX+
5
B
TX-
6
NC
RX-
7
GND
GND
8
GND
GND
Line sequence of
T568B
1. orange with white
2. orange
3. green with white
4. blue
5. blue white white
6. green
7. brown with white
8. brown
RJ45 crystal head
Picture 2.3.2

User Manual V2.4
8
2. Insert the network cable into anyone RJ45 port on anyone inverter
3. Insert the other network cable into anyone RJ45 port on second inverter
4. Make the needed monitoring inverters in series in the same way
5. Connect the PV data collector WIFIKIT to a inverter with the bus,（constitute serial
LAN）
6. Connect the power supply adapter to data collector, then insert into the socket
Picture 2.3.3
Note: Must cut off the power supply before connection. Please make sure that all the connections are
completed, and then power the inverters and PV data collectors. Otherwise may cause personal injury or
equipment damage.
2.4 WiFi settings
2.4.1 Wireless Network
Insert the wifi part, turn on
DC power, 3minutes later
continue the next part