Omnimount SC120FM User manual

Max screen size: 42" - 80" (107-203 cm)
Max weight 120 lbs (54.4 kg)
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
777-61-062-G-02 rev F
SC120FM
Large Full Motion TV Wall Mount

2
BEFORE YOU BEGIN
Make sure you have power and signal outlets in the right spot. Now is a great time to check the length of your
cables and make sure they will reach the appropriate outlets. Nothing’s worse than completing a perfect
installation just to realize there’s nowhere to plug in the TV!
Avoid TV glare. Find a mounting location for your TV where there is no glare from surrounding windows or lights.
A great way to check for glare is to have a friend hold a mirror where you intend to hang your TV. Take a seat; if you
can see windows or bright lights in the reection that’ll cause glare on your TV once installed.
After nding a location that works best for you, grab your tools and you’re ready to begin!
Remember, if you’re ever in doubt during this process, watch the installation video online or call our friendly
customer care team at 1.800.MOUNT-IT (800-668-6848).

777-61-062-G-02 rev F
TOOLS NEEDED
WOOD
CONCRETE
Ø 7/32" (5,5 mm)
10mm
Ø 3/8" (9,5-10 mm)
2
1
1/2"

4
CONTENTS
A
C
B
D
E
This product is designed to move easily
when mounted to the wall and the weight
of your TV is attached. Movements may be
dicult before your TV is attached.
1x 1x
1x
1x
Part # Description
A Wall Plate
B TV Plate
C VESA Extenders
D Cable Tie
E Wall Template
F Stud Finder/Level
4x
F
1x

777-61-062-G-02 rev F
CONTENTS
TV Hardware
MOUNT Hardware
M8
4x
ST8 x 65mm M8
4x4x
M4 x 7mm
2x 2x
M4/M5
M6 x 15mm
EXTENDER Hardware
M6
M6
8x8x 8x
M6/M8 x 5mm
x4
M6/M8
4x
M6 x30mm
4x M8 x30mm
4x
M6/M8 x 10mm
x4
M6 x15mm
4x
M8 x15mm
4x
M8 x45mm
4x

6
QUESTIONS? 1-800-MOUNT-IT (1-800-668-6848)
Disclaimer – OmniMount Systems has extended every eort to ensure to accuracy and completeness of
this manual. However, OmniMount Systems, Inc. does not claim that the information covers all
installation or operational variables. The information contained in this document is subject to change
without notice or obligation of any kind. Regarding the information contained herein, OmniMount Systems,
Inc. makes no representation of warranty, expressed or implied, and assumes no responsibility for accuracy,
suciency, or completeness of the information contained in this document.
WARNING: FAILURE TO READ, THOROUGHLY UNDERSTAND, AND FOLLOW ALL INSTRUCTIONS CAN
RESULT IN SERIOUS PERSONAL INJURY, DAMAGE TO PERSONAL PROPERTY, OR VOIDING OF FACTORY WARRANTY!
It is the responsibility of the installer to ensure all components are properly assembled and installed using the instructions provided. If you do not understand
these instructions or have any questions or concerns, please contact customer service at 1-800-668-6848 or [email protected]. Do not attempt to install
or assemble this product if the product or hardware is damaged or missing. In the event that replacement parts or hardware are needed, please contact
Customer Service at 1-800-668-6848 or [email protected]. International customers needing assistance should contact the Dealer from which they
purchased the product. The included hardware is designed for use on vertical walls constructed of wood studs or solid concrete. A wood stud wall is
dened as consisting of a minimum of 2x4 wooden studs (2" wide by 4" deep) with a maximum of 5/8" drywall. A concrete wall is dened as solid concrete
with a minimum depth of 6" (152 mm). The included hardware is not designed for use with metal studs or cinderblock walls. If you’re uncertain about the
construction of your wall, then please consult a qualied contractor or installer for assistance. For a safe installation, the wall you are mounting to must
support 4 times the weight of the total load. If not, then the surface must be reinforced to meet this standard. The installer is responsible for verifying that
the wall structure and hardware used in any installation method will safely support the total load.

777-61-062-G-02 rev F
WEIGHT / SCREEN SIZE CAPACITY
120 lbs
54.4 kg
USE WITH TVs LARGER THAN THE MAXIMUM WEIGHT AND/OR SCREEN SIZE MAY RESULT IN
INSTABILITY CAUSING POSSIBLE INJURY.
42"- 80"

8
1. ATTACHING THE TV PLATE TO THE TV
Using a Phillips screw driver attach the TV plate to the TV. Because this mount was designed to t a number of TV congurations,
we’ve included a variety of screws and spacers. You will only be using 4 screws in this installation step. Spacers may be needed to
accommodate TVs with a curved back, recessed mounting locations, or in the event that one of the TV rail obstructs the power or
signal plug outlets. Spacers may also be mounted behind the TV rail to take up additional slack. Now is also an opportune time to
plug in all of your power and signal cables into the TV.
TV Hardware
M6/M8 x 5mm
x4
M6/M8
4x
M6 x30mm
4x M6/M8 x 10mm
x4
M6 x15mm
4x
4x
M8 x30mm
4x
M8 x15mm
4x M8 x45mm

777-61-062-G-02 rev F
NOTE: If the TV plate does not reach the mounting holes on the back of your TV, you will need to install the extenders.
Please see the next page for the extender installation.
ATTENTION: If your AV access is obstructed the
at panel plate is designed for vertical adjustment
with 100mm x 100mm hole patterns.
1
2

10
EXTENDER INSTALLATION
These extenders will allow you to mount TV’s with up to a 600mm x 400mm
hole pattern. Attach each extender to the TV plate using shown hardware.
Once this step is complete, refer to the previous step for attaching the TV
plate to the TV.
M6 x 15mm
EXTENDER Hardware
M6
M6
8x
8x 8x

777-61-062-G-02 rev F
M6/M8 x 5mm
x4
M6/M8
4x
M6 x30mm
4x M6/M8 x 10mm
x4
M6 x15mm
4x
4x
M8 x30mm
4x
M8 x15mm
4x M8 x45mm

12
CONCRETE WALL INSTALLATION
Place unit on the wall at desired height making sure its level, then mark the holes for drilling.
This mount was designed to be used on two dierent types of walls. One being a wood stud wall and the other being a solid
concrete wall. Below is the pilot hole sizes for both types of walls. You’ll also notice this information printed on the WALL
HARDWARE pack.
Locate and mark one wood stud. Wood studs are usually 16" apart. A stud nder is a great tool to use; however, they aren’t
always 100% accurate. A great way to verify a stud location is to tap a thin nail into the wall where you think the stud is. Do
this a number of times to verify the center and edges of the stud.
Place unit on the wall at desired height aligning holes with studs and making sure its level, then mark the holes for drilling.
WOOD STUD INSTALLATION
2. ATTACHING THE WALL PLATE TO THE WALL
WOOD
CONCRETE
Ø 7/32" (5,5 mm)
Ø 3/8" (9,5-10 mm)

777-61-062-G-02 rev F
16”(406.4mm)
31
1
2
2
Dual Stud
Concrete

14
WALL INSTALLATION
Wood
MOUNT Hardware
1/2"
ST8 x 65mm
4x
1/2"
Concrete
ST8 x 65mm M8
4x4x
M8
M8
4x
4x

777-61-062-G-02 rev F
Dual Stud
Concrete

16
POSITION ARM ON WALL PLATE
Choose one of the options for positioning your arm side-to-side.

777-61-062-G-02 rev F
Center Left Right

18
1. We suggest having a friend help lift your TV and hang it on the wall plate. Please ensure that the puck on the back of the TV
plate seats into the Wall/Arm Assembly.
2. Install the shown hardware on either side of the TV plate using a Phillips screwdriver to secure it to the Wall/Arm Assembly.
3. HANG YOUR TV
M4 x 7mm
2x
2x
M4/M5

777-61-062-G-02 rev F
12NOTE: For safe and proper installation be sure to
install the locking /leveling screws as shown.
Level monitor before securing screws.

20
Route your cables through the cable tie attached to the extension. Be careful of possible pinch points and feel free to use
extra cable bundling or zip ties for a clean installation.
4. CABLE ROUTING
D1x