manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Omnimount
  6. •
  7. Rack & Stand
  8. •
  9. Omnimount QM100-T User manual

Omnimount QM100-T User manual

Thank you for purchasing an OmniMount product.
Warranty: Limited Lifetime on manufacturing defects and workmanship.
Specifications are subject to change without prior notice.
Every effort has been made to provide accurate and error-free assembly and installation instructions. OmniMount Sys-
tems disclaims liability for any difficulties arising from the interpretation of information contained in these instructions.
If OmniMount products are used for purposes other than their original intent, OmniMount, its distributors and retailers
shall not be held responsible or liable for injuries or property damage, direct, indirect, or consequential, which may arise
from the inability to use this product safely, properly, and in the manner for which it has been designed and manufac-
tured. Warranty does not apply to products which have been lost, damaged by misuse, abuse, or accident.
OmniMount Systems, Inc.
8201 South 48th Street • Phoenix, AZ 85044-5355
1-800-MOUNT-IT • www.omnimount.com
P/N 1001156—Rev. B 7/2004
Step 4
Install the Wall Plate onto the Monitor Plate using
the supplied 1/4”-20 Screws (3) and Nylon Washers
(10).
Carefully hang the monitor by sliding the keyhole
slots on the Wall Plate over the protruding screws, as
indicated by arrows in Fig. 5.
Tighten the screws holding the Wall Plate.
Note: Tilting the monitor away from the wall, im-
proves access to the wall mounting screws.
Fig. 5
Step 5
Adjust tension of the Tilt Screw (Fig. 5) to provide
the desired degree of adjustability or locking of tilt
mechanism.
QM100T:
LCD Tilt Mount
Installation Instructions
IMPORTANT: Consult a qualified installer if you have any questions
regarding the proper installation of this wall mount system.
Questions? 1-800-MOUNT IT
• Universal VESA mount
• Easy to install
• +15º to -5º of tilt
• Can be inverted
• 40 lbs (18.1 Kg) capacity
QM100T
ID Description Qty
1 Monitor Plate 1
2 Wall Plate 1
3 Screw: 1/4”-20 X 1/2” 4
4 Wall Screw: 6mm x 50mm 2
5 Wall Anchor 2
6 Screw: 4mm x 8mm 4
7 Screw: 4mm x 12mm 4
8 Screw: 5mm x 8mm 4
9 Screw: 5mm x 12mm 4
10 Nylon Washer 4
Step 1
Determine the desired location for the monitor.
Important: Make sure there is adequate mounting space available for
the monitor, considering the monitor dimensions.
The QM100T is supplied with the necessary hardware for either
Wooden Stud Mounting or Masonry Mounting. Determine your
mounting type and proceed accordingly. Fig. 1
Wooden Stud Mounting: Using an electronic stud
finder, locate the center of the wooden stud.
Position the Wall Plate (2) in desired mounting
location over stud.
Level the Wall Plate with a bubble level, and then
using the wall bracket as a template, mark mounting
hole locations over the center of the stud.
Drill 2 mounting holes into the stud using a 5/32” drill
bit.
Masonry Mounting: Position the Wall Plate (2) in desired
mounting location on wall.
Level the Wall Plate with a bubble level, and then using the
wall bracket as a template, mark mounting hole locations on
wall.
Drill 2 mounting holes using a 5/16” masonry bit. Insert
Wall Anchors (5) into the mounting holes, and lightly tap
them flush to the wall with a hammer.
Caution: Wall Anchors should only be used for masonry
mounting. NEVER use wall anchors to mount the QM100T
to drywall.
Step 2
Mount Wall Plate with supplied Wall Screws (4) , and check fit. (Fig. 1) Leave Wall Screwsprotruding slightly so that
Wall Plate can slide over screw heads for installation/removal of monitor.
Remove Wall Plate from wall, and set aside for Step 4.
Attach Monitor Plate to back of the monitor with 4mm or 5mm
supplied hardware. (6-9) (Fig. 4) Check the monitor’s owners man-
ual for correct length screw to use.
Caution: Never force screws into the monitor, as damage may oc-
cur.
Fig. 4
Step 3
The QM100T can be mounted to allow the moni-
tor to Tilt Up or Tilt Down.
To have monitor Tilt Up, the Monitor Plate
should be attached to the monitor with the Pivot
Screw at the top, as shown in Fig. 2.
To have monitor Tilt Down, the Monitor Plate
should be attached to the monitor with the Pivot
Screw at the bottom, as shown in Fig. 3.
Fig. 2 Fig. 3

Other Omnimount Rack & Stand manuals

Omnimount FP-CL User manual

Omnimount

Omnimount FP-CL User manual

Omnimount 17FBHDT User manual

Omnimount

Omnimount 17FBHDT User manual

Omnimount VB100F User manual

Omnimount

Omnimount VB100F User manual

Omnimount VB150F User manual

Omnimount

Omnimount VB150F User manual

Omnimount HM1 User manual

Omnimount

Omnimount HM1 User manual

Omnimount IES1 User manual

Omnimount

Omnimount IES1 User manual

Omnimount AB1-HTS User manual

Omnimount

Omnimount AB1-HTS User manual

Omnimount WS-1 User manual

Omnimount

Omnimount WS-1 User manual

Omnimount OM1100594 User manual

Omnimount

Omnimount OM1100594 User manual

Omnimount CI40FML User manual

Omnimount

Omnimount CI40FML User manual

Omnimount OM10051 User manual

Omnimount

Omnimount OM10051 User manual

Omnimount OM1100601 User manual

Omnimount

Omnimount OM1100601 User manual

Omnimount 30.0 WB User manual

Omnimount

Omnimount 30.0 WB User manual

Omnimount OM1100586 User manual

Omnimount

Omnimount OM1100586 User manual

Omnimount VB35C User manual

Omnimount

Omnimount VB35C User manual

Omnimount 10067 User manual

Omnimount

Omnimount 10067 User manual

Omnimount OC150T User manual

Omnimount

Omnimount OC150T User manual

Omnimount OCSBA User manual

Omnimount

Omnimount OCSBA User manual

Omnimount TVM-13 User manual

Omnimount

Omnimount TVM-13 User manual

Omnimount PRO-PJT User manual

Omnimount

Omnimount PRO-PJT User manual

Omnimount OWS60 User manual

Omnimount

Omnimount OWS60 User manual

Omnimount 10238 User manual

Omnimount

Omnimount 10238 User manual

Omnimount G3FP User manual

Omnimount

Omnimount G3FP User manual

Omnimount CP-4 User manual

Omnimount

Omnimount CP-4 User manual

Popular Rack & Stand manuals by other brands

Westinghouse MT80A TILT Installation and assembly

Westinghouse

Westinghouse MT80A TILT Installation and assembly

Sanus VisionMount MF202 manual

Sanus

Sanus VisionMount MF202 manual

tau PARK Use and maintenance manual

tau

tau PARK Use and maintenance manual

Edsal UR-185PBB Assembly instructions

Edsal

Edsal UR-185PBB Assembly instructions

Techly PRO 100 user manual

Techly

Techly PRO 100 user manual

Vivitek WM-3Z installation manual

Vivitek

Vivitek WM-3Z installation manual

Lucasey PCEC2410B installation instructions

Lucasey

Lucasey PCEC2410B installation instructions

ChargeArm CA01 Installation

ChargeArm

ChargeArm CA01 Installation

Racking Solutions WR001 Assembly instructions

Racking Solutions

Racking Solutions WR001 Assembly instructions

Amphenol Procom XG-COMBI MOUNT manual

Amphenol Procom

Amphenol Procom XG-COMBI MOUNT manual

Velleman Toolland MP60 user manual

Velleman

Velleman Toolland MP60 user manual

UPC 3536 Assembly instructions

UPC

UPC 3536 Assembly instructions

PT W5182 owner's manual

PT

PT W5182 owner's manual

Savant Shade Double Drive Quick reference guide

Savant

Savant Shade Double Drive Quick reference guide

Kargo Master 40280 installation guide

Kargo Master

Kargo Master 40280 installation guide

Atdec AV Cart 75 installation guide

Atdec

Atdec AV Cart 75 installation guide

Premier Mounts Universal Tabletop Stand PSD-TTS Dimensional drawing

Premier Mounts

Premier Mounts Universal Tabletop Stand PSD-TTS Dimensional drawing

PEERLESS SR1G Installation and assembly

PEERLESS

PEERLESS SR1G Installation and assembly

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.