Omnimount TVM-13 User manual

4
Specifications are subject to change without prior notice.
Every effort has been made to provide accurate and error-free assembly and installation. OmniMount Systems disclaims
liability for any difficulties arising from the interpretation of information contained in these instructions. If OmniMount
products are used for purposes other than their original intent, OmniMount, its distributors and retailers shall not be
held responsible or liable for injuries or property damage, direct, indirect, or consequential, which may arise from the
inability to use this product safely, properly, and in the manner for which it has been designed and manufactured.
Thank you for purchasing an OmniMount product.
Step 6
Place platform trim piece (14) over front lip of platform.
Hold trim piece in place with your fingers while using
thumbs to spread locking tabs out and down, until they lock
in place underneath the platform.
Step 7 Thread open end of security strap (19) up through
a slot on the outer edge of platform, across the
platform, and then down through the other slot.
Place self-adhesive anti-slip pads (8) on platform.
Place TV squarely onto platform.
Pull two ends of security strap over TV, thread
strap ends through strap buckle (as shown), and
secure tightly.
Step 8
Adjust platform for desired amount of tilt:
To increase tilt angle, hold top of TV and carefully push front edge of
platform backwards.
To decrease tilt angle, hold top of TV and carefully pull front edge of
platform forwards.
With tilt angle set, turn front edge of platform at right angles
to support arm. Insert small hex wrench through holes in
bottom of platform support as shown, and tighten
platform tilt screws securely.
Step 9
Press nose piece (4) into place at end of support arm, as shown.
OmniMount Systems, Inc.
8201 South 48th Street • Phoenix, AZ 85044-5355
1-800-MOUNT-IT • www.omnimount.com
P/N 1002759—Rev. B 4/2005
TVM-13 Television Wall Mount
Assembly Instructions
◊ TVM13 designed for: 9” - 13” CRT Televisions
◊ TVM13Maximum Weight Capacity: 60 lbs. (27.2 Kg)
• TV platform tilts and swivels
• Wall arm pivots
• Black security strap included
• Accepts optional Component Mount
IMPORTANT: Consult a qualified installer if you have any questions
regarding the proper installation of this wall mount system.
Questions? 1-800-MOUNT IT

2
Model: TVM-13
Item Description Quantity
1 Wall Bracket 1
2 Platform 1
3 Platform Swivel
Bracket
1
4 Nose Piece 1
5 Wall Bracket Cover 1
6 Square Washer 1
7 Flat Washer 1
8 Anti-slip Pads 4
9 Hex Wrench 1
10 Platform Main Bolt 1
11 Platform Tilt Screws 2
12 Platform Lock Nut 1
13 Platform Slide Nuts 2
14 Platform Trim Piece 1
15 Support Arm 1
16 Support Arm Pivot
Bolt
1
17 Large Hex Wrench 1
18 Wall Anchors 4
19 Wall Bracket Bolts 4
20 Security Strap 1
21 Small Hex Wrench 1
3
Step 1
Use electronic stud finder to locate center of stud.
Note: When mounting to masonry, go directly to Step 2
Step 2
Use wall bracket (1) as template to mark mounting hole locations.
Step 3
Wooden Stud Mounting:
Using 1/8” drill bit, drill mounting holes to a depth of 2”.
Using a 10mm wrench, bolt the wall bracket to the wall with
the supplied lag bolts (19).
Note: To make installation easier, dab a bit of liquid
soap onto the threads before driving the bolt into the
stud.
Masonry Mounting:
Use a 3/8” masonry drill bit, and drill mounting holes to a
depth of 2”.
Insert wall anchors (18) into mounting holes, and tap flush with hammer.
Using a 10mm wrench, bolt the wall bracket to the wall with the supplied lag
bolts (19).
Step 4
Slide wall bracket cover (5) over support arm, with flat side facing wall.
Insert platform tilt screws (11) up through two
countersunk holes in bottom of Platform
Swivel Bracket (3).
Thread square platform slide nuts (13) onto
platform tilt screws. Loosely secure nuts using
small hex wrench (21).
Place flat washer (7) in depression in center of
platform swivel bracket.
Insert platform main bolt (10) through center
of washer.
Place platform assembly on top of platform
swivel bracket, with main bolt passing through
center hole.
Install square washer (6) onto platform main
bolt, and then thread platform lock nut (12)
onto platform main bolt. Tighten with hex
wrench (9). Do not
over-tighten or plat-
form will not swivel.
Step 5
Insert support arm into wall bracket. Insert support arm
pivot bolt and secure with lock nut. Do not over tighten
lock nut, or arm will not swing freely.
Snap wall bracket cover into place.