ON Semiconductor ADIS16360/PCBZ User manual

©Semiconductor Components Industries, LLC, 2015
February, 2019 −Rev. 5
1Publication Order Number:
EVBUM2258/D
EVBUM2258/D
PYTHON Family Sensor
Evaluation Kit Quick
Start Guide
This guide will help you get up and running using the
PYTHON Family of CMOS Image Sensors with the
ON Semiconductor G3 Evaluation Hardware and Sensor
Studio II Software.
Before You Start
•Evaluation Hardware and Supported Image Sensor
Verify that you have the required hardware for the
sensor being evaluated:
♦G3 FPGA board
♦Imager head board for the sensor being evaluated
♦Optional lens mount kit
•Sensor Studio II Software
The most recent version can be downloaded at
www.onsemi.com
•USB
USB 2.0 and USB 3.0 are supported.
•Computer
Windows 7 and Windows 10 64 bit, 2+ GHz processor,
8 GB RAM, USB 3.0/2.0 connection.
•Power Supply
12 V DC, 2 A, with 2.1 mm center positive DC power
jack.
•Cables
2 meter USB 3.0 cable with Type A on the host end and
micro 3.0 on the hardware end is included with the kit.
•Lens
A C/CS mount lens holder is provided with the kit. For
larger optics, an F−mount is available in the optional
Lens Mount Kit.
•Table−top Tripod (recommended)
Install Software
Install the software by running the appropriate
“setup.exe” file, and check the boxes for installing the USB
3.0 drivers if they have never been installed.
Note that the 64-bit version of the USB3 driver currently
is not digitally signed. See ReadFirst_InstallerInstructions.
pdf document, which is part of the SensorStudio installer, for
information on driver installation.
Consult PleaseReadBeforeInstall.pdf, which comes with
the SensorStudio installer, for more information.
Assemble Evaluation Hardware
•Install image sensor on image sensor headboard making
sure that the image sensor is in the proper orientation.
•If using lens mount kit, assemble the appropriate
configuration for the optic you intend to use (C or F).
(see instructions provided in the kit)
•Plug the headboard into the G3 Capture Card and
secure with card guide clips provided.
•If using the 1/4−20 mounting feature on the G3 Frame,
ensure that your mounting screw does not contact the
bottom side of the FPGA circuit board.
•Plug in power and communications cables
With the Evaluation Kit powered off, insert the USB
cable into your PC. Insert the power plug into the
receptacle on the Imager/FPGA board. Turn on the
Power. Use Device Manager to verify “Truesense
USB3” seen by the system.
Run Sensor Studio II
•Shortcut
To properly configure the shortcut icon, right click,
choose properties and then select the compatibility tab.
Set the OS for your OS and enable “run as admin”.
The latter is needed if you install Sensor Studio II in the
standard Program Files area which is owned by admin.
•Launch Program
Double click the Sensor Studio II desktop icon to
launch the software.
•Select Plugin
Click the plugin button . Then choose the correct
plugin in the list:
♦Use PYTHON480 for PYTHON480 device
♦Use PYTHON48 for PYTHON 300/500/1300/2000/
5000 devices
♦Use PYTHONxK for PYTHON 10K/12K/16K/25K
devices
♦An image display window and the control GUI will
appear on the screen
www.onsemi.com
EVAL BOARD USER’S MANUAL

EVBUM2258/D
www.onsemi.com
2
•Connect to Hardware
♦Select the “Connection” tab within the control GUI
♦Click the Connect button
♦The yellow indicator will change to green indicating
that a connection has been established. The system is
now ready to image. If there is a failure, the status
box will turn red displaying an error message with
more information.
Next Steps
Sensor Studio II provides a number of controls to evaluate
operation of the sensor, including image capture,
processing, and characterization.
Additional information on these controls is included in the
Sensor Studio II help system, which is available from the
HELP menu by selecting “SS2 and Python Help”.
For additional help in system setup, please contact
ON Semiconductor at www.onsemi.com/imagesensors or
by e-mail at [email protected].
LisAll brand names and product names appearing in this document are registered trademarks or trademarks of their respective holders.

www.onsemi.com
1
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or
other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s
product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is
subject to all applicable copyright laws and is not for resale in any manner.
The evaluation board/kit (research and development board/kit) (hereinafter the “board”) is not a finished product and is as such not available for sale to consumers. The board is only intended
for research, development, demonstration and evaluation purposes and should as such only be used in laboratory/development areas by persons with an engineering/technical training
and familiar with the risks associated with handling electrical/mechanical components, systems and subsystems. This person assumes full responsibility/liability for proper and safe handling.
Any other use, resale or redistribution for any other purpose is strictly prohibited.
The board is delivered “AS IS” and without warranty of any kind including, but not limited to, that the board is production−worthy, that the functions contained in the board will meet your
requirements, or that the operation of the board will be uninterrupted or error free. ON Semiconductor expressly disclaims all warranties, express, implied or otherwise, including without
limitation, warranties of fitness for a particular purpose and non−infringement of intellectual property rights.
ON Semiconductor reserves the right to make changes without further notice to any board.
You are responsible for determining whether the board will be suitable for your intended use or application or will achieve your intended results. Prior to using or distributing any systems
that have been evaluated, designed or tested using the board, you agree to test and validate your design to confirm the functionality for your application. Any technical, applications or design
information or advice, quality characterization, reliability data or other services provided by ON Semiconductor shall not constitute any representation or warranty by ON Semiconductor,
and no additional obligations or liabilities shall arise from ON Semiconductor having provided such information or services.
The boards are not designed, intended, or authorized for use in life support systems, or any FDA Class 3 medical devices or medical devices with a similar or equivalent classification in
a foreign jurisdiction, or any devices intended for implantation in the human body. Should you purchase or use the board for any such unintended or unauthorized application, you shall
indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor
was negligent regarding the design or manufacture of the board.
This evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC,
CE or UL, and may not meet the technical requirements of these or other related directives.
FCC WARNING – This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation purposes only and is not considered by ON Semiconductor to
be a finished end product fit for general consumer use. It may generate, use, or radiate radio frequency energy and has not been tested for compliance with the limits of computing devices
pursuant to part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this equipment may cause interference with radio
communications, in which case the user shall be responsible, at its expense, to take whatever measures may be required to correct this interference.
ON Semiconductor does not convey any license under its patent rights nor the rights of others.
LIMITATIONS OF LIABILITY: ON Semiconductor shall not be liable for any special, consequential, incidental, indirect or punitive damages, including, but not limited to the costs of
requalification, delay, loss of profits or goodwill, arising out of or in connection with the board, even if ON Semiconductor is advised of the possibility of such damages. In no event shall
ON Semiconductor’s aggregate liability from any obligation arising out of or in connection with the board, under any theory of liability, exceed the purchase price paid for the board, if any.
For more information and documentation, please visit www.onsemi.com.
PUBLICATION ORDERING INFORMATION
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: [phone]
LITERATURE FULFILLMENT:
Email Requests to: [email protected]
ON Semiconductor Website: www.onsemi.com
Europe, Middle East and Africa Technical Support:
Phone: [phone]
For additional information, please contact your local Sales Representative
◊