Onbon BX-Y08 User manual

User manual
Cross LED display screen
Version: V1.1 Release time: 2021.4.19
Statement
Without the written permission of the company, no unit or individual
shall imitate, copy, transcribe or translate part or all of the contents of this
manual without authorization. Do not use this manual in any form or any

www.onbonbx.com 第 2页
method (electronic, mechanical, photocopying, recording or other possible
methods) for commodity dissemination or for any commercial or
profit-making purposes.
The product specifications and information mentioned in this manual
are for reference only, and will not be notified if the content is updated.
Unless there is a special agreement, this manual is only used as a guide,
and all statements and information in this manual do not constitute any form
of guarantee.
catalogue

www.onbonbx.com 第 3页
About software.........................................................................................................................4
Device connection...................................................................................................................4
Add cross screen.................................................................................................................... 6
Cross parameter configuration..............................................................................................7
Contact us................................................................................................................................ 9
Introduce
Thank you for purchasing our LED control card. I hope you can enjoy the excellent
performance of this product. The design of the LED control card complies with international and
industry standards, but if it is improperly operated, it may still cause personal injury and property
damage. In order to avoid the danger that the equipment may bring and to benefit from your
equipment as much as possible, please follow the relevant instructions in this manual when
installing and operating the product.

www.onbonbx.com 第 4页
About software
Do not modify, decompile, disassemble, decrypt, or reverse engineer the software installed on
this product. The above behaviors are illegal.
User guidance
Device connection
First connect the computer and the router, and then connect the Y series control card to the
router with a network cable, and connect the control card to the cross screen through a flat
cable. The following is an example of connecting the Y08 control card. See the figure below for
details:
Y04 and Y08 series controllers support cross screens.

www.onbonbx.com 第 5页
Add Screen
Open the Led show YQ software, select the "parameter settings" menu → "Set
Screen Parameters", in the "Screen Parameters Settings" interface, click on the "find"
at the bottom right of the interface, as shown in figure 1 below. Then enter the "Add
Screen" interface, as shown in Figure 2 below.
Picture 1
Internet
Y08control card
PC
Router
Internet line
Cross
screen
flat cable

www.onbonbx.com 第 6页
In the pop-up "Add screen" interface, check "Add all screens", and finally click "find" to
successfully bind the screen to the controller.
Picture 2
Add cross screen
Return to the "Screen Parameters Setting" interface, click "Cross Screen", and click "OK" in the
pop-up dialog box to complete the addition of cross screen, as shown in the following figure.

www.onbonbx.com 第 7页
Picture 2
Cross parameter configuration
After adding the cross screen, the screen name on the right will change to "Cross Screen".
Select "Cross Screen Parameter Configuration" and set the width and height of the controller.

www.onbonbx.com 第 8页
Picture 3
1. In the drop-down list under "Module Size", you can select the commonly used module width and
height. If it is not a commonly used module, you can click "Custom" to set the width and height of the
module by yourself. Here assume 1 The width of each module is 64 and the height is 32.
2. The number of top modules: a width of 1 means the width of 1 module, and a height of 2 means
the height of 2 modules.
3. Number of middle modules: a width of 3 means the width of 3 modules, and a height of 2 means
the height of 2 modules.
4. The number of bottom modules: a width of 1 means the width of 1 module, and a height of 2
means the height of 2 modules.
5. After setting the number of modules, click "Set" to complete the setting of the cross screen.

www.onbonbx.com 第 9页
Contact us
Shanghai ONBON Technology Co.,ltd (Headquarters)
Address: 7 Floor, Tower 88, 1199#, North Qinzhou Road, Xuhui District, Shanghai City,
China
Tel Phone: [phone]
Fax: [phone]
Website: www.onbonbx.com
ONBON (Jiangsu) Optoelectronic Industrial Co.,LTD
Address: 1299#, Fuchun Jiang Road, Kunshan City, Jiangsu Province, China
Sales Contacts
Tel: [phone] 0086-15800379719
Email: [email protected]
Second Development
Tel: [phone]
Email: [email protected]
iLEDCloud
Website: http://www.iledcloud.com/
Public Wechat Sales wechat