OOZE VAULT Manual

STORAGE
CHAMBER
Clean parts aer each use to keep your Vault in working condion.
Keep away from water and extremely hot or cold temperatures. Always
turn the baery off aer each session and before cleaning.
To clean the baery connecon, use a q-p slightly dipped in rubbing
alcohol. Avoid soaking with excess alcohol, and swab the area where the
atomizer connects to the baery. Allow to dry completely before use.
To clean the coils, unscrew the atomizer from the baery. Soak a q-p
with rubbing alcohol and scrub the inside of the coil to remove oil and
resin build-up. If stubborn residue remains, replace the coil with a fresh
one. Use an alcohol wipe to clean the baery and mouthpiece to sanize
between uses.
To ensure the best experience, please read and understand the
instrucons fully before your first use of the VAULT.
One Year Warranty is included with VAULT purchase. Warranty DOES
NOT apply to VAULT baery at fault from use of NON VAULT
CHARGER, or if there is any physical damage. If for any reason your
device stops working, please contact us to open a claim.
STORAGE CHAMBER
CHARGING INSTRUCTIONS
The VAULT includes a storage
chamber for 510 thread cartridge.
To access, unscrew boom cap,
screw cartridge on to the cap to
keep it secured and screw the cap
back onto the Vault.
VAULTneeds to be charged
when LED light flashes 10 mes.
Plug the VAULT micro USB
charger into the charging port
located on the side of the unit.
LED light will flash while
charging, light will turn when
baery is 10% charged and
when the VAULT is fully charged.
IMPORTANT: Please use wall
outlet to charge device for best
charging experience.
CLEANING INSTRUCTIONS
WARRANTY
 
+STORAGE CHAMBER
HOW TO USE
INSTRUCTION GUIDE

POWER BUTTON
STORAGE
CHAMBER
HEATING
CHAMBER
MOUTH TIP
MICRO USB CHARGER PORT
ADJUSTABLE VOLTAGE 2.6V - 3.8V
HOW TO TURN ON/OFF
PREHEAT MODE
TURN ON: Press POWER BUTTON 3 mes quickly.
Voltage LED light will be on for 1.5 seconds indicang the device is ON.
TURN OFF: Press POWER BUTTON 3 mes quickly.
Voltage LED light will flash once indicang the device is OFF.
2.6 - 3.0V 3.0 - 3.4V 3.4V - 3.8V
Adjust voltage by rotang the dial on the boom of the
baery. Select voltage by posioning the line parallel to
the power buon. Voltage range is 2.6V - 3.8V.
VAULT includes 10 second Hold Time. During use
baery will flash 5 mes on auto shut off.
When the VAULT is in standby, the LED light will not turn on.
Click the power buon once to wake up the baery.
HOW TO ADJUST BATTERY VOLTAGE
Press POWER BUTTON 2 mes quickly to begin 15 Second Preheat mode.
LED Light will flash mulple colors during preheat mode. Press POWER
BUTTON 1 me to deacvate.
1. Unscrew the mouthpiece from the dual quartz wax tank heang chamber
2. Place extracts inside the heang chamber on the coil.
3. Screw the mouthpiece back onto the heang chamber.
4. Screw the wax tank onto the VAULT.
HOW TO LOAD EXTRACTS INTO THE WAX TANK
DUAL
QUARTZ
WAX TANK
 
+STORAGE CHAMBER
HOW TO USE
INSTRUCTION GUIDE
• 450 MAH BATTERY •
ADJUSTABLE VOLTAGE 2.6V - 3.8V
15 SECOND PREHEAT MODE
• STORAGE CHAMBER •
• DUAL QUARTZ WAX TANK •
• MICRO USB CHARGER •
P R O D U C T F E A T URES