OpenEye OE-C9112F12 User manual

QUICK START GUIDE
This quick start guide provides
only basic information on the
camera’s settings and operation for
initial installation. Please read the
user manual for optimal camera
congurations.
Scan the QR code or go to
openeye.net/downloads
Find the latest product
documentation and software.
Copyright ©2022 OpenEye.
All Rights Reserved. Information contained in this
document is subject to change without prior notice.
OpenEye does its best to provide accurate information but
cannot be held responsible for typos or mistakes.
Liberty Lake, WA, USA
509.232.5261
openeye.net
CONNECTIONS
Waterproof Cable
11Thread lock capThread lock cap 44Rubber “O” ringRubber “O” ring
22Rubber plugRubber plug 55Camera cableCamera cable
33RJ45 enclosureRJ45 enclosure
5431
2
11Reset ButtonReset Button
To restore the camera to factoryTo restore the camera to factory
defaults:defaults:
1.1. Disconnect power for 30Disconnect power for 30
seconds.seconds.
2.2. Reconnect power and wait 30Reconnect power and wait 30
seconds.seconds.
3.3. Press and hold the resetPress and hold the reset
button for 20 seconds.button for 20 seconds.
22MicroSD Card SlotMicroSD Card Slot
Supports up to 512GB microSDSupports up to 512GB microSD
card for Edge storage.card for Edge storage.
Do not add or remove theDo not add or remove the
microSD card when the cameramicroSD card when the camera
is powered on.is powered on.
1
2
11RJ-45RJ-45 For network and PoE connectionsFor network and PoE connections
22Audio I/OAudio I/O PinkPink Audio In (Line In)Audio In (Line In)
GreenGreen Audio Out (Line Out)Audio Out (Line Out)
33Power (12vDC)*Power (12vDC)* BlackBlack DC 12V -DC 12V -
RedRed DC 12V +DC 12V +
44Alarm I/OAlarm I/O
11Alarm In -Alarm In -
22Alarm In +Alarm In +
33Alarm Out -Alarm Out -
44Alarm Out +Alarm Out +
4
3
*12vDC power input port should be plugged when not in use.
12MP Ultra HD Fisheye
OE-C9112F12
37690AC
1
2
NOTE: The product is intended to be supplied by external power source (UL listed/ IEC 60950-1/ IEC 62368-1) which output is complied
with ES1,PS2/LPS, output rating 1) 12Vdc, 0.93 A minimum or 2) 48Vdc, 0.27A minimum (PoE), ambient temperature 55°C
minimum.

CONTENTS
INSTALLATION
1. Apply template sticker to desired
camera location.
2. Drill anchor holes using included
mounting template.
3. Remove mounting template.
4. Insert anchors.
5. Mount camera.
6. Connect network cable with
included waterproof cable
connector.
NOTE: To change this IP address please refer
to your Apex recorder manual.
ASSIGNING AN
IP ADDRESS
OpenEye IP cameras are set to DHCP
by default. If a DHCP server is not
detected after 2 minutes, the camera
will default to IP address 192.168.51.2.
If you are not using a DHCP server,
NCM will allow you to batch congure
a static IP address.
The IP address for the camera network
on your Apex recorder is 192.168.51.1.
OE-C9112F12
Fisheye Camera
Waterproof Cable
Connector
Self-Tapping
Screws/M4/6.8MM
(x3) &
Plastic Anchors
4-5MM (x3)
Security Torx
Tool
Quick Start
Guide
Mounting Template
Selecting multiple cameras and enter-
ing IP address 192.168.51.2 will set
an IP address on all selected cameras,
starting at 192.168.51.2 and increase
per camera.
1. Open Network Camera Manager.
2. Select applicable camera(s).
3. Input starting IP address, Subnet
Mask, Gateway, DNS.
4. Apply changes.
5. Wait 60 seconds before refreshing
NCM.
CONNECTING TO THE
IP CAMERA
To access the camera setup menu,
you need to open Network Camera
Manager (NCM) utility. NCM is pre-
installed on all OpenEye Recorders,
and is also available for download on
the OpenEye website for installation on
your personal computer or laptop.
1. Open Network Camera Manager.
2. Locate your camera on the
Network Camera Manager list.
3. To open the web browser, select
the camera and click LOAD.
NOTE: OpenEye IP cameras ship
without a default password.
DEFAULT USERNAME
AND PASSWORD
PRODUCT FEATURES
Camera
Maximum
Resolution
4000x3000 (Software Dewarping)
2976x2976 (Edge Dewarping)
Frame Rate at
Maximum
Resolution
20FPS @ 4000x3000
H.264/H.265/MJPEG
Video Streams 4
ONVIF Prole S / G / Q / T Compliant
Day/Night Auto / Manual / Light Sensor
Wide Dynamic
Range True WDR
Environmental and Power
Power
Consumption
PoE - Max 12.95W
12vDC - Max 11.16W
Input Voltage 12vDC / PoE
IP Rating IP66
Impact Rating IK10
The admin user password can be set
using the following methods:
1. OpenEye recorders running Apex
2.6 or newer will automatically
set a new unique password when
added in setup, if a new password
has not already been set.
2. Connect to the camera directly
through a Web Browser and follow
the onscreen prompts.
3. Use the Network Camera Manager
(NCM) Utility.
Username: admin
Set the Default Camera Password
Use the QR code or link for instructions on
dening a unique camera password:
https://answers.openeye.net/Install/Adding_
Cameras_and_Camera_Settings/Default_
Camera_Password
NOTE: The NCM software manual can be
found at https://answers.openeye.net/
Install/Adding_Cameras_and_Camera_
Settings/Network_Camera_Manager