Optical Systems Design OSD2801 User manual

Doc. ID 10117901
OPERATOR MANUAL
OSD2801
2 Port SFP+ 10G
OEO 3R REPEATER
The OSD2801 is a high performance 10G Optical-
Electrical-Optical (OEO) converter (3R Repeater) used for
connection between 10Gbps fiber to fiber equipment. The
OSD2801 functions as a fiber media converter or as a
fiber repeater for long distance transmission. OEO for
network backbone (SAN, LAN, MAN) and supports
SDH/SONET STM-64/OC-192, 10G fiber channel, 10G
Ethernet etc. It normally operates over two fibers but is
optionally available for 1 fiber operation
(1310nm/1550nm/CWDM/DWDM).
Specifications and Features
▲ Loopback support
▲ Supports Jumbo Frame
▲ Transparent transport and very low delay
▲ Supports ITUT prescribed DWDM/CWDM
wavelength
▲ 3R Function (Regeneration, Reshaping,
Retiming)
▲ Hot pluggable
▲ Available for singlemode operation over a
variety of link budgets
▲ Available for operation over 1 or 2 fibers
▲ Operates over 0 to +50°C temperature range
▲ High performance cooling system (fan cooled
when case temperature reaches 50°C)
Fitting SFP Connectors
Care should be taken when inserting/removing the SFP
connectors as SFP modules are Electrostatic (ES) sensitive and
Electrostatic Discharge (ESD) precautions should be taken
when installing. Ensure that the SFP is fully engaged and
latched into position.
Inserting SFP – Ensure that the SFP lever is in the locked
position and insert into SFP port. Gently push the SFP until it
locks into place. Remove dust cap and fit fiber cable.
Removing SFP – Remove fiber connector. Pull the SFP lever
down to unlock SFP from housing. Using the lever, gently pull
the SFP out.
Case Dimensions
Below is an outer case drawing showing the dimensions (mm).
Power Connection
The voltage range of the OSD2801 is 100V
AC
to 240V
AC
.
Connect power using the supplied IEC power cable to the
connector located at the rear of the case.
Signal Connection
The appropriate SFP optical modules should be inserted
into the SFP port.
The optical fiber cable must be terminated with the
appropriate type optical connector (SC for single fiber and
LC for 2 fiber). Before connection, inspect the ends of the
connectors to ensure that no dust or dirt is present as it
could contaminate the modem connector and result in poor
performance.
If it is necessary to clean the cable connectors use
isopropyl alcohol and lint free tissue to remove
contamination.
Port Allocation and LED indicators
LED Indicators
LED Colour Function
P1 Loop Green SFP+1 Loopback is on
P1 LNK Green SFP+1 Link established
P2 Loop Green SFP+2 Loopback is on
P2 LNK Green SFP+2 Link established
LOOP Green Loopback is on
PWR Green Power
Inserting
SFP
Removing
SFP
1
2
LOOP P2 LOOP P1 LOOP
PWR SFP+2 P2 LNK SFP+1 P1 LNK
156
32
128

Doc. ID 10117901
Internal Switch Settings
Switches are accessible by carefully unscrewing the
spring mounting screw and removing the board from the
module housing.
Switch Speed
10.3-11.7G 9.95-11.3G 8.5G
S1 On Off Off
S2 Off Off On
Switch Position Function
S3 On SFP+1 Loopback is On
Off Loopback is Off
S4 On SFP+2 Loopback is On
Off Loopback is Off
Note: Power to the unit must be off when setting switches
Technical Specifications
Specification Performance
Equipment Function 3R Repeater
Transmission Speed 8.5Gbs – 11.7Gbps
Access Type
10G LAN (10.3-11.7G)
10G WAN (9.95-11.3G)
Fiber Channel (8.5G)
Interface Type SFP+ to SFP+
Power Requirements 100V
AC
to 240V
AC
Power Connector IEC Plug (supplied)
Dimensions (mm) 156W x 128D x 32H
Weight of Module 0.76kg
Operating Temperature
0 to 50°C
Relative Humidity 5 to 90% non-condensing
▲ ELECTROMAGNETIC COMPATIBILITY
WARNING: This is a Class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take
adequate measures.
▲ OPTICAL OUTPUT OPERATION
WARNING: Laser Safety: Class 1 Laser Product per
IEC/EN 60825-1:2014 standard.
Class 1
The OSD2801 is a Class 1 laser product.
Precautions
▲ All service personnel should be provided training as
to the hazards of direct viewing of laser radiation and
of the precautionary measures during servicing of
equipment
▲ Areas where laser products are installed should be
restricted in access to trained service personnel only
and appropriate warning signs posted in the work
area.
▲ All laser apertures should be covered by protective
covers when not connected to optical fibers. Never
leave outputs uncovered.
▲ Laser equipment should be positioned above or
below eye level where possible. Apertures should be
positioned away from personnel
▲ Protective eyewear should be worn in the vicinity of
laser equipment
Warranty/Repairs
Thank you for purchasing equipment by Optical Systems Design
(OSD). OSD warrants that at the time of shipment, its products
are free from defects in material and workmanship and conforms
to specifications.
For warranty period and repair service please contact your local
OSD distributor.
OPTICAL SYSTEMS DESIGN PTY LTD
7/1 Vuko Place, Warriewood 2102.
PO Box 891, Mona Vale,
NSW, Australia 1660.
Phone: [phone]
Fax: [phone]
S1 S2 S3 S4
Spring
Mounting
Screw