opticis OMM-1000 User manual

User’s Manual Version 1.2
OMM-1000
Multi-format matrix
16x16 DVI / HDMI / SDI Matrix
Doc No. : OM-D130711 / Rev1.2

2
TABLE OF CONTENTS
Chapter 1. Introduction and installation................................................................................................ 4
1.1 Key features ............................................................................................................................ 4
1.2 Shipping group ........................................................................................................................ 5
1.3 Notice of safe usage................................................................................................................ 5
1.4 Physical description................................................................................................................. 6
1.5 Installation ............................................................................................................................... 7
1.5.1 Initialization ......................................................................................................................... 7
1.5.2 Connection for remote control ............................................................................................ 7
1.6 EDID Configuration.................................................................................................................. 7
Chapter 2. Control setup....................................................................................................................... 9
2.1 TCP/IP..................................................................................................................................... 9
2.1.1 TCP/IP setup of PC............................................................................................................. 9
2.1.2 Launching Telnet ................................................................................................................ 9
2.2 RS-232 .................................................................................................................................. 10
2.2.1 Launching HyperTerminal................................................................................................. 10
Chapter 3. Key button operation......................................................................................................... 11
3.1 LINK mode............................................................................................................................. 11
3.2 UNLINK mode .......................................................................................................................11
3.3 FUNCTION mode..................................................................................................................11
3.3.1 Gateway............................................................................................................................ 12
3.3.2 Subnet Mask.....................................................................................................................12
3.3.3 IP Address ........................................................................................................................12
3.3.4 MAC Address....................................................................................................................13
3.3.5 UDP Port Number.............................................................................................................13
3.3.6 Multi Viewer ...................................................................................................................... 14
3.3.7 Video Generator................................................................................................................ 14
3.3.8 Monitoring Output ............................................................................................................. 15
3.3.9 EDID Configure.................................................................................................................15
3.3.10 Baud Rate......................................................................................................................... 16
3.3.11 Control Lock...................................................................................................................... 17
3.3.12 Reset Mode.......................................................................................................................17
Chapter 4. PC program operation....................................................................................................... 18
4.1 Basic setup............................................................................................................................19
4.1.1 Connect Info...................................................................................................................... 19
4.1.2 Channel Name..................................................................................................................20
4.1.3 Video Generator................................................................................................................ 20
4.1.4 Control Lock Mode............................................................................................................ 20
4.1.5 Network............................................................................................................................. 20
4.2 EDID setup ............................................................................................................................ 20
4.3 Operation...............................................................................................................................21
4.3.1 Input / output connection...................................................................................................22
4.3.2 Input channel status..........................................................................................................22
4.3.3 Output channel status.......................................................................................................23
4.3.4 Multi-viewer.......................................................................................................................23
Chapter 5. Web control panel operation.............................................................................................26

3
Chapter 6. Command input operation.................................................................................................27
6.1 Command input structure...................................................................................................... 27
6.2 Examples of command inputs ............................................................................................... 28
6.2.1 Link input and output......................................................................................................... 28
6.2.2 Input and output status .....................................................................................................28
6.2.3 Network setting ................................................................................................................. 29
6.2.4 Video generator setting..................................................................................................... 29
6.2.5 Monitor output port setting................................................................................................ 30
6.2.6 EDID control command..................................................................................................... 31
6.2.7 Baud rate setting for RS-232 ............................................................................................ 31
6.2.8 Multi-viewer card (QDVI-O) setting...................................................................................32
6.2.9 Slot status request ............................................................................................................33
6.2.10 Control lock command...................................................................................................... 34
Chapter 7. Firmware update...............................................................................................................35
Chapter 8. Trouble shooting............................................................................................................... 38
Chapter 9. Specification...................................................................................................................... 39
9.1 General specification.............................................................................................................39
9.2 Power Specification...............................................................................................................40
9.3 SDI video input and output scaling condition ........................................................................40
Chapter 10. Warranty Information ...................................................................................................... 41
Chapter 11. Safety Instructions .......................................................................................................... 42
Chapter 12. Maintenance ................................................................................................................... 44
Chapter 13. UL /EN Statement...........................................................................................................45
Chapter 14. Symbol Definitions.......................................................................................................... 46

4
Chapter 1. Introduction and installation
Purpose
The modular matrix, OMM-1000 enables to connect between various video sources and displays and
it offers flexible installation with other video controllers or control software. The input and output cards
are composed of 4 ports DVI, therefore user can easily configures any input and output channels from
4X4 to 16X16 by plugging the cards into OMM-1000 mainframe.
Introduction
The OMM-1000 modular matrix enables to switch up to 16 different DVI, HDMI and SDI sources to 16
different digital displays. It can be configured using 4 input and output cards and each card has 4 ports
of input and output.
Any input source, whether it is a HD-DVD player, Blue-Ray player or a computer with high-resolution
graphics, can be routed to DVI and HDMI output digital display.
Note) SDI is not a licensed HDCP interface and if the content received from HDMI is protected by
HDCP, there should be no output from the SDI slot.
1.1 Key features
▪Up to 16 DVI, HDMI and SDI inputs and outputs can be configured.
▪Each card has 4 input or 4 output ports and 4 cards can be fitted into input and output bays.
▪Has Electrical DVI, HDMI, SDI and Optical DVI input and output cards.
▪Any input formats can be converted to DVI, HDMI and SDI. But the resolution between the
formats should be same.
▪Complies with DDC/HDCP (Electrical DVI and HDMI cards only).
▪Supports up to WUXGA (1920x1200) at 60Hz refresh ratio for DVI or 1080P at 60Hz for
HDMI and SDI (Maximum 2.97Gbps bandwidth).
▪Supports 3 types of EDID management:
Default Mode.
Auto Mix Mode.
Output Copy Mode.
▪Supports various control methods:
Key buttons operation
Command input (Such as Hyper terminal by RS-232 and Telnet by TCP/IP)
Web panel control (TCP/IP)
PC program by RS-232 and UDP
▪Works with OPTICIS DVI, HDMI, and SDI optical extender for long signal extension.

5
▪Has dual-power supplier for hot-swappable and load-sharing.
▪Equips multi-viewer card to be used in various monitoring systems.
▪Provides diagnostic function for quick trouble shooting.
▪Has video generator output and monitoring output for easy installation.
1.2 Shipping group
▪OMM-1000, Modular matrix chassis: 1 EA
▪Input output cards: Option
SDVI-4EI, 4 ports electrical DVI input card
SDVI-4EO, 4 ports electrical DVI output card
SDVI-1FI, 4 ports 1 fiber optical DVI input card
SDVI-1FO, 4 ports 1 fiber optical DVI output card
HDMI-4EI, 4 ports electrical HDMI input card
HDMI-4EI, 4 ports electrical HDMI output card
SDI-4EI, 4 ports electrical SDI input card
SDI-4EO, 4 ports electrical SDI output card
QDVI-O, Multi-viewer card
▪AC power cord: 1 EA
▪Power supplier: 1 EA (Dual power supplier is an option)
▪User manual: 1 EA
▪Firmware download cable: 1 EA (Use only this accessory specified by the manufacturer)
▪RS-232 cable (Straight type): 1 EA
▪PC software CD: 1 EA
1.3 Notice of safe usage
We recommend you to read following warning, precaution and information before start to
operate the OMM-1000 modular matrix.
▪Use of the equipment in a manner not specified by the manufacturer may result in ire-
coverable damage.
▪Keep the unit away from liquid, magnetic and combustible substances.
▪Do not place heavy weight on the unit.
▪Move away from noisy environment such as vibration or impact.
▪Do not install the unit vertically. / Do not disassemble the unit.
▪Carry the unit using the handle in front of the panel with two (2) Users.

6
1.4 Physical description
The OMM-1000 modular matrix chassis is mountable on a 19” standard rack. Key buttons,
LCD display and reset switch are placed on the front panel as shown in Figure 1-1.
Figure 1-1 Front panel of OMM-1000
All Input and output cards, interface ports and power supplier are placed on the rear panel as
below.
▪Input bay for 4 input cards (left side)
▪Output bay for 4 output cards (right side)
▪SERVICE, RJ-11 receptacle for firmware upgrade
▪RS-232, Serial communication port
▪LAN, RJ-45 receptacle for TCP/IP or UDP control
▪REFERENCE OUTPUT for internal video source for easy installation
▪MONITORING OUTPUT for internal output port to monitor input signal
▪Power supplier (Dual-power is an option)
Figure 1-2 Rear panel of OMM-1000

7
1.5 Installation
1.5.1 Initialization
▪Put insert the cards into each input or output bay according to user interface.
▪All input or output cards have the same connection way, and tighten the screws just until
snug against the main frame. Then, please make sure the cards are fully seated.
▪Connect the provided AC power cord to AC power inlet and turn on switch on the front
panel. Then, OMM-1000 will start initialization process (To turn it off completely, pull out
AC power cord, switch on the front panel is reset switch).
▪‘OMM-1000 Starting’will be shown on LCD display.
▪After 7~10 sec, ‘OMM-1000 Booting complete’message and hardware and firmware
version information will be shown.
▪Now, OMM-1000 is ready to receive commands from user.
1.5.2 Connection for remote control
▪Connect the OMM-1000 to PC with the supplied RS-232 cable.
▪Connect the OMM-1000 to PC with LAN cable with RJ-45 connector.
[NOTE] Typically, the IP address of PC connected to the network is configured by DHCP
server. But, if the PC is connected directly to the OMM-1000, the network server will
not able to assign the IP address. In this case, network information of PC should be
set manually.
The default IP address of OMM-1000 is 192.168.1.117. Before connecting OMM-
1000 to your network, please verify the availability of IP address in your network.
The IP address can be reconfigured by key button, PC program or command lines
over RS-232 or TCP/IP.
1.6 EDID Configuration
▪EDID (Extended Display Identification Data) is an information set that is provided by a
display to describe its capabilities to a graphic source. It enables a graphic source to identify
the connected display.
▪The information set includes: manufacturer, product type, phosphor or filter type, timings
supported by the display, display size, luminance data and (for digital displays only) pixel
mapping data.
▪Once the graphic source reads the information set (usually during the booting process), the
EDID determines the optimal format for a connected display.
▪OMM1000 supports storing of EDID information to an EEPROM for each Input.

8
▪OMM1000 has three-way EDID settings, 1) Default Mode: default EDID from the factory, 2)
Output Copy Mode: read of EDID from any target display and copy in input port and the most
advanced one is 3) Auto Mix Mode: analyzing of all EDID from the attached displays and
store optimized EDID in input port to avoid any compliance problems in the field.
Figure 1-3 Concept of EDID setting and working in OMM-1000 modular matrix
As depicted in Figure 1-3, once EDID is configured, each EDID is stored in EEPROM in Input
ports. As a result, the video sources are able to read EDID from the EEPROM during booting
process even though the OMM-1000 and connected displays are not powered on yet.
EEPROM1
EEPROM2
EEPROM3
EEPROM16
EDID
INTERFACE
CONTROL
Read/Write
Sources
INPUT 1~16
Displays
OUTPUT 1~16
WRITE EDID
.
.
.
.
.
.
.
.

9
Chapter 2. Control setup
The OMM-1000 modular matrix can be controlled in various ways such as command input (RS-232,
TCP/IP), Web control panel (TCP/IP), supplied PC program (RS-232, UDP) as well as key button on
the front panel. To do this, PC should be configured properly.
2.1 TCP/IP
2.1.1 TCP/IP setup of PC
TCP/IP, the abbreviation of Transmission Control Protocol (TCP) and the Internet Protocol (IP)
is commonly used protocol to control remote computers.
To control OMM-1000 over TCP/IP, set network properties of PC as below (Explained here is
based on Win 7 OS).
▪Open Control Panel.
▪Select Network Status in Network and Internet menu.
▪Select Adapter setting.
▪Select Local Area Connection and right click to open property.
▪Select Internet Protocol Version 4 (TCP/IPv4)
▪Enter IP, Subnet mask, Gateway and DNS server address, compatible with the current
network setting of OMM-1000.
▪Click OK to terminate IP setup session.
[Note] If the IP address of OMM-1000 is 192.168.001.117, the PC IP address should be
chosen as 192.168.001.nnn; where ‘nnn’ can range from 000 to 255 except 117.
2.1.2 Launching Telnet
Telnet is a terminal program embedded in Window OS system to access remote computers
using TCP/IP protocol. With the network setting of the PC as above, launch Telnet as below.
▪Make sure PC and OMM-1000 are connected by Ethernet.
▪Click Start menu and select Run.
▪Type CMD to open command window.
▪Type ‘telnet 192.168.1.117’(Type current IP address of OMM-1000).

10
▪Press ENTER then, “==Welcome to OMM-1000==”and “== TELNET control ==”
messages will be shown.
▪Type command inputs to control OMM-1000. (Refer to Chap. 5)
2.2 RS-232
2.2.1 Launching HyperTerminal
The OMM-1000 modular matrix provides RS-232 serial communication. The simplest way to
control OMM-1000 over RS-232 is using embedded software in Windows OS, HyperTerminal.
To launch Hyper Terminal (Explained here is based on Windows XP OS. Hyper Terminal is
not available on Win 7.):
▪Connect the PC to OMM-1000 over RS-232 cable.
▪Select Start > Programs > Accessories > Communications > HyperTerminal.
▪Enter a name and choose an icon in Connection Description window and click OK.
▪In Connect To window, ignore the Country, Area Code and Phone Number fields but select
available COM port of PC to be connected to OMM-1000 then, click OK.
▪In COM Properties window, set the parameters as below:
Bits per second (baud rate): 115200 (115200 is default baud rate of OMM-1000)
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
[Note] Bit per second of Hyper Terminal should be set as same as baud rate of OMM-1000.
▪Click OK to save the parameters.
▪Go Start > Programs > Accessories > Communications > HyperTerminal, then new icon
will be shown. Then select it to launch Hyper Terminal.
▪Type command inputs to control OMM-1000 (Refer to Chap. 5)

11
Chapter 3. Key button operation
3.1 LINK mode
▪It configures input / output connections for cross-switching.
1) Press LINK key button.
2) Press an input key button - LCD will display current connected output.
3) Press single or multiple output key buttons to select desired outputs.
4) Outputs can be deselected by pressing the each output key button again.
5) Press ENTER key button to save the configuration.
6) To configure next Input / output connection, repeat steps 1 to 5.
3.2 UNLINK mode
▪It unlinks input /output connection.
1) Press SHIFT key button.
2) Press LINK key button.
3) Press the input key button to be disconnected.
4) Press ENTER key button.
3.3 FUNCTION mode
▪It configures basic setting of OMM-1000 to be controlled by command input and PC program.
▪Press FUNCTION to see features –FUNCTION key button will cycle the following features
repeatedly:
Gateway
Subnet Mask
IP Address
Mac Address
UDP Port Number
Multi-viewer (It is activated when QDVI-O is in output bay)
Video Generator
Monitoring Output
EDID Configure
Baud Rate
Control Lock
Reset Mode

12
3.3.1 Gateway: Press FUNCTION key button once
▪The cursor shows that it is selected and activated.
▪Input 3 key button decreases the number.
▪Input 4 key button increases the number.
▪Input 1 and 2 key buttons move the cursor left and right.
======Gate Way======
O: 192. 168. 001. 001
N: 192. 168. 001. 001
▪Modify the Gate way address to be used for your network.
▪Press ENTER key button to complete the process.
▪The default setting is 192.168.001,001
3.3.2 Subnet Mask: Press FUNCTION key button two times
▪The cursor shows that it is selected and activated.
▪Input 3 key button decreases the number.
▪Input 4 key button increases the number.
▪Input 1 and 2 key buttons move the cursor left and right.
====Subnet Mask====
O: 255. 255. 255. 000
N: 255. 255. 255. 000
▪Modify the Subnet mask address to be used for your network.
▪Press ENTER key button to complete the process.
▪The default setting is 255.255.255.000.
3.3.3 IP Address: Press FUNCTION key button three times
▪The cursor shows that it is selected and activated.
▪Input 3 key button decreases the number.
▪Input 4 key button increases the number.
▪Input 1 and 2 key buttons move the cursor left and right.
=====IP Address=====
O: 192. 168. 001. 117
N: 192. 168. 001. 117

13
▪Modify the IP address to be used for your network.
▪Press ENTER key button to complete the process.
▪The default setting is 192.168.001.117.
3.3.4 MAC Address: Press FUNCTION key button four times
▪The cursor shows that it is selected and activated.
▪Input 3 key button decreases the number.
▪Input 4 key button increases the number.
▪Input 1 and 2 key buttons move the cursor left and right.
=====MAC Address====
O: 00.11.AA.EE.DD.FF
N: 00.11.AA.EE.DD.FF
▪Modify the MAC address to be used for your network.
▪Press ENTER key button to complete the process.
3.3.5 UDP Port Number: Press FUNCTION key button five times
▪It makes number setting, data range from 0 to 65535.
▪The cursor shows that it is selected and activated.
▪Input 3 key button decreases the number.
▪Input 4 key button increases the number.
▪Input 1 and 2 key buttons move the cursor left and right.
=========Function Mode========
Port Number
Old data: 03000
New data: 03000
▪Modify the UDP port number to be used for your network.
▪Press ENTER key button to complete the process.
▪The default UDP port number is 03000.
[Note] Port number setting in this section is used for UDP with supplied PC program not
TCP/IP with web browser or Telnet. For TCP/IP, port number 23 is fixed value.

14
3.3.6 Multi Viewer: Press FUNCTION key button six times
▪Multi-viewer card, QDVI-O can choose 4 inputs among 16 inputs of OMM-1000 and
configure and output these input signals with 7 different layouts. For more details, refer to
chap. 4.3.4.
▪The cursor shows that it is selected and activated.
▪Input 1 and 2 key buttons move the menu.
▪Input 3 key button decreases the number.
▪Input 4 key button increases the number.
====Multi Viewer====
SLOT No.: 01
Resol: 01 800x600
Layer: Layer 01
1) Select the SLOT No. by pressing input 3 or 4 key button. It shows location where the
QDVI-O is inserted among output slots. If only one QDVI-O is inserted the number will
be fixed and not changed.
2) Select the output resolution.
3) Select Layout.
4) Press ENTER key button to complete the process.
3.3.7 Video Generator: Press FUNCTION key button seven times
▪It changes resolution and pattern of video generator.
▪The cursor shows that it is selected and activated.
▪Input 1 and 2 key buttons move the menu.
▪Input 3 key button decreases the number.
▪Input 4 key button increases the number.
==Video Generator==
Resol: 01 800x600
Image: 01 V Bar Stop
OSD: ON
1) Select the resolution, pattern and OSD by pressing the key buttons as guided above.
2) Press ENTER key button to complete the process.
[Note] OSD shows the resolution and pattern information on the top left of the display.

15
3.3.8 Monitoring Output: Press FUNCTION key button eight times
▪It allocates input to Monitor Output port for monitoring uses.
▪The cursor shows that it is selected and activated.
▪Input 3 key button decreases the number.
▪Input 4 key button increases the number.
=Monitoring Output=
Old Input: 01
New Input: 01
1) Connect a display to the Monitoring Output port and any video sources to the DVI input
ports on the real panel.
2) Select an input port by pressing input 3 or 4 key button.
3) Press ENTER key button to complete the process.
3.3.9 EDID Configure: Press FUNCTION key button nine times
▪It sets EDID information in input port.
▪OMM-1000 supports three types of EDID setting: Default Mode, Auto Mix Mode and Output
Copy Mode. For more information, refer to Chap. 5.2.
▪The cursor shows that it is selected and activated.
▪Input 1 and 2 key buttons select YES and NO.
▪Input 3 and 4 key buttons move left and right (Change EDID mode).
▪Input 5 and 6 key buttons move down and up (Decrease and increase the port number).
===EDID Configure===
Entry EDID
Configure? _1: Entry
1) Press input 1 key button to enter the EDID Configure Mode.
===EDID Configure===
Input: 01 Default
Default Mode?
1: Y 2: N 3: << 4: >> 5: ∨6: ∧
[Note] The EDID configuration that is shown next to the input number on the LCD display is
current EDID mode
2) Select an input port by pressing input 5 or 6 key button.

16
3) Press input 3 or 4 key button to change EDID mode.
3-1) If you select Default Mode, default EDID will be restored for allocated inputs.
===EDID Configure===
Input: 01 Default
Default Mode?
1: Y 2: N 3: << 4: >> 5: ∨6: ∧
Press input 1 key button then, the OMM-1000 will recover the Default EDID to
allocated input as below.
===EDID Configure===
EDID Copying….
EDID Reading….
3-2) If you select Auto Mix Mode, mixed EDID of all attached displays will be saved in
allocated input.
3-3) If you select Output Copy Mode, OMM-1000 reads EDID from any target displays
and copies it in allocated input.
[Note] There is Edit Data Mode but it is used to modify existing EDID to make new
EDID working with specific systems. It is not recommended for general user. For
further information, please contact [e-mail]
3.3.10Baud Rate: Press FUNCTION key button ten times
▪It sets RS-232 Baud Rate. OMM-1000 supports 9600, 19200, 38400, 57600, 115200bps.
=====Baud rate=====
Old baud: 115200
New baud: 115200
▪Input 3 key button decreases the number.
▪Input 4 key button increases the number.
▪Press ENTER key button to complete the process.
▪The default setting is 115200

17
3.3.11Control Lock: Press FUNCTION key button eleven times
▪It locks and unlocks the controls such as Web, RS-232, TCP/IP, UDP and key button
====Control Lock====
Web Lock? UnLock
Data Lock? UnLock
Key Lock? UnLock
▪Input 1 and 2 key buttons move the cursor up and down.
▪Input 3 key button moves Lock.
▪Input 4 key button moves UnLock.
▪Press ENTER key button to complete the process.
3.3.12Reset Mode: Press FUNCTION key button twelve times
▪It resets OMM-1000. It starts rebooting and restores all default setting.
▪Press Input 1 key button to complete the process.

18
Chapter 4. PC program operation
Run the setup.exe to install OMM-1000 PC program. The OMM icon will be shown on the wallpaper.
Double click it to launch PC program for OMM-1000.
The PC program provides a user-friendly graphic interface alternative to key button input and
command input operation.
Copy OMM ver1.x.exe file in any directories in your PC and double click it to run. Then, initial window
of PC program for OMM-1000 as below will open.
Fig 4-1 PC program of OMM-1000

19
4.1 Basic setup
Click Set Config button to set the communication method, input / output name, Video generator and
so on. Then, the Set Config window as below will open.
Fig 4-2 Set Config window of OMM-1000 PC program
4.1.1 Connect Info
▪Select the way of control method between RS-232 and Ethernet (UDP) by click the radio
buttons.
▪In case of RS-232 control, enter available COM port number of your PC and select baud
rate. The baud rate should be same as that OMM-1000. (115200 is default)
▪In case of Ethernet, enter IP address of OMM-1000 and port number. 3000 is default port
number of OMM-1000.
▪Click save button and close Set Config window then click Connect button on PC program
of OMM-1000 to start it.

20
▪If the connection is properly made, current status of OMM-1000 will be shown at the
bottom side of PC program.
4.1.2 Channel Name
▪User can allocate specific names for all inputs and outputs to distinguish them
▪On Fig 4.2, The name of Camera #1 was assigned for Input CH05 and Wall display #3 for
output CH07.
▪Click Save button to save it then, these will be applied on the PC program as shown in Fig
4-1.
4.1.3 Video Generator
▪Select the resolution and pattern of video generator.
▪Click Apply button to save it.
4.1.4 Control Lock Mode
▪It locks and unlocks the controls such as Web, Data control (RS-232, TCP/IP and UDP)
and key button input.
▪Click Apply button to save it.
4.1.5 Network
▪It changes network information of OMM-1000.
▪Click Apply button to save it.
4.2 EDID setup
OMM-1000 offers 3 types of EDID setting for easy installation with various displays in the market.
To set the EDID option for each input port, click Set EDID button then, Setup EDID window as
below will open.
Fig 4-3 Setup EDID window of OMM-1000 PC program