Opticon RS-3000 User manual

Specifications Manual
Spec manual RS-3000
Sub Miniature 2D data collector
Revision 1
Copyright (C) 2021 Opticon Sensors Europe B.V.
All rights reserved.
RS-3000
Sub miniature, High-Performance, 2D data collector

RS-3000 Specifications Manual
ii
Prelininary. The information in this document is subject to change without notice.
© 2021 Opticon. All rights reserved.
This manual may not, in whole or in part, be copied, photocopied, reproduced, translated,
or converted to any electronic or machine-readable form without prior written consent
from Opticon.
Limited Warranty and Disclaimers
Please read this manual carefully before installing or using the product.
Serial Number
A serial number appears on all Opticon products. This official registration number is directly
related to the device purchased. Do not remove the serial number from your Opticon
device. Removing the serial number voids the warranty.
Warranty
Unless otherwise agreed in a written contract, all Opticon products are warranted against
defects in materials and workmanship for two years after purchase excluding batteries.
Opticon will repair or, at its option, replace products that are defective in materials or
workmanship with proper use during the warranty period. Opticon is not liable for damages
caused by modifications made by a customer. In such cases, standard repair charges will
apply. If a product is returned under warranty and no defect is found, standard repair
charges will apply. Opticon assumes no liability for any direct, indirect, consequential or
incidental damages arising out of use or inability to use both the hardware and software,
even if Opticon has been informed about the possibility of such damages.
Packaging
The packing materials are recyclable. Damage caused by improper packaging during
shipment is not covered by the warranty.
Trademarks
Trademarks used are the property of their respective owners.
Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of
OPTOELECTRONICS Co., Ltd., 12-17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-
0002. TEL [phone]; FAX [phone]
Support
USA
Europe
Phone: [phone]
Phone: [phone]
Email: [email protected]
Email: [email protected]
Web: www.opticonusa.com
Web: www.opticon.com

RS-3000 Specifications Manual
iii
Revision History
This document is a compilation of all individual specification manuals for the MDI-4000
Series of scan engines.
Product Name: RS-3000 Specifications Manual
Edition
Date
Page
Section
Description of Changes
First
September 16, 2019
-
-
Initial release.

RS-3000 Specifications Manual
iv
Table of Content
1Abstract........................................................................................................................... 6
2Overview ......................................................................................................................... 6
3Physical Features............................................................................................................. 7
3.1 Dimensions.............................................................................................................. 7
3.1.1 RS-3000 Dimensions............................................................................................ 7
3.1.2 Ring scanner bracket dimensions ........................................................................ 8
3.2 Weight..................................................................................................................... 9
4Environmental Specifications .......................................................................................... 9
4.1 Temperature ........................................................................................................... 9
4.2 Humidity.................................................................................................................. 9
4.3 Ambient Light Immunity.......................................................................................... 9
4.4 LED light immunity .................................................................................................. 9
4.5 Electrical Noise ........................................................................................................ 9
4.6 Vibration Strength................................................................................................. 10
4.7 Drop Impact Strength............................................................................................ 10
5Optical Specifications .................................................................................................... 10
5.1 Basic Optical Specifications ................................................................................... 10
6Component specification .............................................................................................. 11
7Electrical specification................................................................................................... 11
7.1 Absolute Maximum Ratings................................................................................... 11
7.2 Recommended Operating Conditions ................................................................... 11
7.3 Battery................................................................................................................... 11
8Serial Label .................................................................................................................... 12
9Regulatory Compliance ................................................................................................. 13
9.1 LED Safety.............................................................................................................. 13
9.2 Product Safety....................................................................................................... 13
9.3 EMC and RED......................................................................................................... 13
9.4 FCC ........................................................................................................................ 13
9.5 RoHS/Reach........................................................................................................... 14
10 Handling Precautions .................................................................................................... 15
10.1 Charging ................................................................................................................ 15
10.2 Excessive Shock or Stress ...................................................................................... 15

RS-3000 Specifications Manual
v
10.3 Bluetooth .............................................................................................................. 16
10.4 Frequency Band..................................................................................................... 16
10.5 Operating Environment......................................................................................... 16
10.6 General Cautions................................................................................................... 16
11 Packaging Specifications ............................................................................................... 17
Table of Figures
Figure 1: Dimensions of the RS-3000.....................................................................................................7
Figure 2: Dimensions of ring scanner bracket ........................................................................................8
Figure 3: Serial label .............................................................................................................................12

RS-3000 Specifications Manual
6
1Abstract
This manual provides specifications for the RS-3000 sub-miniature data collector that
features a 2D scan engine.
2Overview
The RS-3000 is a very compact battery powered data collector with a built-in 2D barcode
scanner. Due to its compact size and its Bluetooth capabilities, the RS-3000 is the ideal
companion scanner for mobile devices like the iPhone/iPad and Android telephones and
tablets. It is so small that is easily fits into your pocket. An important accessory for the RS-
3000 is the ring scanner bracket that transforms the product into a wearable. Combined
with the very light weight of the RS-3000 makes it an ideal product for hands-free operation.
The key features of the RS-3000 are the following:
•Super small design, the smallest in the industry: Even though the RS-3000 is a full
featured data collector it measures just 3.2 x 4.8 x 2.0 cm, not much bigger than the
average keychain.
•Configurable and Programmable: The RS-3000 is built onto the proven technology
used in previous data collectors such as the OPN-2006 and the PX-20 that make the
product programmable. All applications such as the OPN-2001 simulation app and
the Bluetooth demos are supported.
•High-speed scanning: The extreme high-performance scan engine in the RS-3000
ensures stress-free scanning and fast response, even in the case of poor-quality
barcodes. It features a high-speed CMOS image sensor that captures images at a
speed of up to 100 fps, which when combined with the fastest global shutter speed
in the industry, enables fast and accurate scanning.
•Accurate battery monitoring: With the build-in battery gas-gauge, the RS-3000 is
able to accurately monitor the remaining charge level and therefore it can prevent
surprise resets that may damage the filesystem.
•Green LED aiming and Warm-White LED Illumination: A well-defined, single line of
green LED light and efficient warm-white LED illumination makes it easy to aim the
scanner while providing safety and long life.
•Designed from the start as a wearable scanner: The RS-3000 can easily be clicked
onto a ring scanner bracket to transform it into a wearable. Combined with the very
light weight of the RS-3000 makes it an ideal product for hands-free operation
•Wireless charging: The RS-3000 can be charged wirelessly with any Qi compatible
charging pad. Of course, it is also possible to charge it via the USB-C port.
•NFC Tag for Bluetooth pairing: The RS-3000 has a build-in tag that can be used my
most modern smart phones for easy Bluetooth pairing.
•Bluetooth: The RS-3000 features a modern Bluetooth 4.2 compliant chip that
supports both Bluetooth classic as well as Bluetooth low energy (BLE).
•USB-C: The RS-3000 comes with a USB-C charging/communications port. It supports
USB-HID (keyboard), USB-COM (serial port) and USB-MSD (hard disk)
•RoHS compliance: The scan engines are RoHS compliant products, as declared by
Optoelectronics Co., Ltd.

RS-3000 Specifications Manual
7
3Physical Features
3.1 Dimensions
3.1.1 RS-3000 Dimensions
32.3 x 47.8 x 20.4 mm (WxLxH)
Figure 1: Dimensions of the RS-3000






RS-3000 Specifications Manual
8
3.1.2 Ring scanner bracket dimensions
41.8 x 47.8 x 44.0 mm (WxLxH)
Figure 2: Dimensions of ring scanner bracket






RS-3000 Specifications Manual
9
3.2 Weight
The weight of the RS-3000 (excluding bracket) is: 50g
4Environmental Specifications
Unless otherwise noted, these conditions apply to all environmental specifications where
applicable.
Environmental Specification Conditions
Condition
Description
Barcode Sample
0.33 mm UPC specified in Chapter 8
Distance
130 mm from the front edge of the scan engine
Angle
α = 0°, β =+15°, γ = 0°
Curvature
R = ∞
Scanning Test
Read at intervals of 300 ms
Power Supply Voltage
3.3 and 5.0 V
4.1 Temperature
Operating Temperature: -20 to 60 °C
Storage Temperature: -40 to 70 °C
Note: Temperature during charging should be between 0 and 45 °C. To protect the battery the RS-3000 will automatically
stop the charging process when the temperature is outside these values.
4.2 Humidity
Operating Humidity 5 to 90% RH (no condensation, no frost)
Storage Humidity 5 to 90% RH (no condensation, no frost)
4.3 Ambient Light Immunity
Scanning performance is guaranteed when the illuminance on the surface of a barcode is
between zero and the following values:
Incandescent Light 10,000 lux
Fluorescent Light 10,000 lux
Sunlight 100,000 lux
Note: Scanning performance is guaranteed if direct ambient light does not enter the light receiving section of the scan
engine.
4.4 LED light immunity
The scan performance of the RS-3000 is unaffected by indoor LED lighting applications.
4.5 Electrical Noise
There shall be no abnormalities when sinusoidal electrical noise (50 Hz to 100 kHz, smaller
than 0.1 Vp-p) is added to the power supply line via the USB port.

RS-3000 Specifications Manual
10
4.6 Vibration Strength
The RS-3000 is guaranteed to withstand the conditions of the following vibration test.
Vibration Test: Increase the frequency of the vibration from 12Hz to 200Hz at accelerated
velocity 32.3m/s2(3.3G) for ten minutes. Continue this routine for 2 hours to X-direction, 2
hours to Y-direction and 4 hours to Z-direction.
4.7 Drop Impact Strength
The RS-3000 is guaranteed to withstand the conditions of the following drop test.
Drop test: Drop the RS-3000 10 times in total, at top, bottom, front, back, left, right, top-left,
top-right, bottom-left and bottom-right faces, from a height of 1.5 meters onto a concrete
floor.
5Optical Specifications
5.1 Basic Optical Specifications
Specification
Characteristics
Scan method
CMOS array area sensor
(black and white)
Number of effective
pixels
(H) × (V)
640 × 480
Image capture speed
Frame rate*1
100 fps
Sensor shutter speed
Minimum shutter speed
30μs
Focal distance
From the front edge of scan engine
115 mm
View angle
Horizontal
Approx. 38.0°
Vertical
Approx. 28.9°
Diagonal
Approx. 46.4°
Auxiliary light source
Warm white LED
-
Color temperature
2600 to 3700K
Maximum Optical Efficiency*2
114 lm/W
Light source for aiming
Single Line Green LED
-
Peak Wavelength
535nm
Maximum Optical Efficiency*2
87.4 lm/W
Minimum contrast
PCS
0.2
Minimum resolution
1D barcodes
0.1mm (4mil)
2D codes
0.169 (6.7 mil)
Barcode width
100mm
Pitch, Skew, and Tilt
Resp. α, β and γ
α = ±65° β = ±65° γ = 360°
Curvature
Radius
R ≧20 mm
Motion tolerance
Speed
2.54m/s
Decode rate
1D barcodes
40
2D codes
25
*1 The fastest speed of image capture.
*2 The reference value extracted from the LED datasheet.
Note: The same basic conditions apply as for the Environmental Specifications (See chapter 4)
Note: For more details on the optical specifications, refer to the MDI-4150 specifications manual.