Oracle SPARC T5-2 User manual

1
SPARC T5-2 Server Getting Started Guide
This guide describes how to install and power on Oracle's SPARC T5-2 server for the first time using the
preinstalled Oracle Solaris OS.
Before performing the procedures in this guide, review the following documents at the Oracle documentation web
site: http://www.oracle.com/goto/t5-2/docs.
■SPARC T5-2 Server Product Notes - For any late-breaking issues that impact installation requirements.
■SPARC T5-2 Server Installation Guide - For overview and more detailed installation information.
■SPARC T5-2 Server Safety and Compliance Manual - For safety and regulatory compliance information.
For additional safety information, refer to the Important Safety Information for Oracle's Sun Hardware Systems,
which is in the shipping kit.
Shipping Kit
1 Server 4 Antistatic wrist strap
2 Cable management assembly (CMA) 5 Printed documents
3 Rackmounting kit 6 AC power cords (quantity 2)
Install Optional Components
Before installing the server into the rack, install any optional components you plan to use
with the server that were not factory installed.
For instructions on installing optional components, refer to the documentation for each component and to the
SPARC T5-2 Server Service Manual.

2
Install the Server
For quick installation and configuration, follow these steps. For more detailed information, refer to the
complete online product documentation set.
Caution - Do not apply power until instructed to do so. This server includes a service processor (SP) that
configures and boots the host server. To properly configure the host server and view SP messages, do not
apply AC power to the server until you make the SP and host networking connections, as described in this
guide.
1. Place the server in its intended location.
For rackmounting and CMA instructions, refer to the SPARC T5-2 Server Installation Guide.
2. Connect a serial cable between the server's SER MGT port and a terminal device.
This connection provides the initial communication with the SP. Set up the server to communicate using
9600 baud, 8 bit, no parity, 1 stop bit. For DTE-to-DTE communication, use a RJ-45 cable that is set up for a
null modem configuration, in which the transmit and receive signals cross over.
3. (Optional) Connect an Ethernet cable between the server's NET MGT port and the network
to which future connections to the SP and host will be made.
Configure the server for the first time through the SER MGT port. After the initial configuration, you can set
up communication between the SP and host through this Ethernet interface.
4. Connect an Ethernet cable between one of the server's NET ports and the network to which
the server will communicate.
5. Connect the power cords to the power supplies and to separate power sources.
The server is equipped with two power supplies. Connect them to separate power sources (200 to 240 VAC)
to provide power redundancy. The server can operate with one power connection, but having only one power
source reduces the redundancy.

3
When the power cords are connected, the SP initializes and the power supply LEDs illuminate. After a
few minutes, the SP login prompt displays on the terminal device. At this time, the host is not initialized or
powered on.
Power On the Server
The following section describes how to power on the host after installing the server.
1. At the terminal device, log in to the SP as root with a password of changeme.
After a brief delay, the Oracle Integrated Lights Out Manager (Oracle ILOM) prompt (->) is displayed.
For optimal security, change the root password. For more information about administration tasks such as
changing passwords, adding accounts, and setting account privileges, refer to the SPARC T5 Series Servers
Administration Guide and the Oracle ILOM documentation at: http://www.oracle.com/goto/ilom/docs
By default, the SP is configured to use DHCP to obtain an IP address. If you plan to assign a static IP address
to the SP, refer to the SPARC T5-2 Server Installation Guide for instructions.
2. Power on the server and redirect the host output to display on the serial terminal device.
-> start /System
Are you sure you want to start /System (y/n)? y
-> start /HOST/console
Are you sure you want to start /HOST/console (y/n)? y

4
Serial console started.
. . .
Server initialization takes several minutes to complete.
To cancel the server initialization, press the #. (Hash+Dot) keys to return to the Oracle ILOM prompt. Then
type: stop /System
Note - To use an OS other than the preinstalled version, refer to the SPARC T5-2 Server Installation Guide.
3. (Optional) Execute other Oracle ILOM commands while the server initialization continues in
the background.
a. To display the Oracle ILOM prompt, press the #. (Hash+Dot) keys.
b. To see information about available Oracle ILOM commands, type: help
To see information about a specific command, type: help command-name
c. To return to displaying host output from the server initialization, type: start /HOST/console
4. When prompted, follow the onscreen instructions and type the configuration information for
your server.
If you are not sure how to respond, accept the default and make changes later when the Oracle Solaris OS is
running. After you confirm the configuration information, the server reboots and displays the Oracle Solaris
login prompt.
5. Log in to the server.
You now can enter Oracle Solaris OS commands at the prompt. For more details, refer to the Oracle Solaris
11 or 10 OS man pages and documentation at:
http://www.oracle.com/goto/solaris11/docs
http://www.oracle.com/goto/solaris10/docs
6. Consider using Oracle virtualization and datacenter management software.
■Oracle VM Server for SPARC is a preinstalled system virtualization feature that provides a discrete
logical grouping with its own operating system, resources, and identity within a single computer system.
You can run a variety of applications in different logical domains and keep them independent for
performance and security purposes.
https://docs.oracle.com/en/virtualization/
■Oracle Enterprise Manager is a data center management tool that provides many features, including
a comprehensive configuration solution for software provisioning, hardware fault analysis, and
performance management.
http://docs.oracle.com/en/enterprise-manager/
Check for the Latest OS Updates, Patches, and Firmware
Some server features are enabled only when certain versions of patches or firmware are installed. Install the
latest available versions for the best performance, security, and stability.

5
1. Review the product notes for your server.
This document describes important product dependencies and late-breaking information.
See “Product Documentation Library” on page 6.
2. Download the latest available versions from My Oracle Support at:
https://support.oracle.com

6
Product Documentation Library
Documentation and resources for this product and related products are available at http://www.oracle.com/goto/
t5-2/docs.
Feedback
Provide feedback on this document at http://www.oracle.com/goto/docfeedback.
Documentation Accessibility
For information about Oracle's commitment to accessibility, visit the Oracle Accessibility Program web site at http:
//www.oracle.com/pls/topic/lookup?ctx=acc&id=docacc.
Access to Oracle Support
Oracle customers that have purchased support have access to electronic support through My Oracle Support. For
information, visit http://www.oracle.com/pls/topic/lookup?ctx=acc&id=info or visit http://www.oracle.
com/pls/topic/lookup?ctx=acc&id=trs if you are hearing impaired.
Copyright © 2013, 2016, Oracle and/or its affiliates. All rights reserved.
Copyright © 2013, 2016, Oracle et/ou ses affiliés. Tous droits réservés.
Part No: E28859-03
Mfg. No: 7047746
February 2016