Oracle SPARC T5-8 User manual

1
This guide describes how to install and power on Oracle’s SPARC T5-8 server for the first time using the
preinstalled Oracle Solaris OS.
Before performing the procedures in this guide, review the following documents at the Oracle documentation
web site: http://www.oracle.com/goto/T5-8/docs
■SPARC T5-8 Server Product Notes - For any late-breaking issues that impact installation requirements.
■SPARC T5-8 Server Installation Guide - For more detailed installation information.
■SPARC T5-8 Server Safety and Compliance Manual - For safety and regulatory compliance information.
■SPARC T5-8 Server Service Manual - For instructions on how to remove or install the server components.
For additional safety information, refer to the Important Safety Information for Sun Hardware Systems, which is
contained in the shipping kit.
Shipment Inventory
1 Server
2 AC power cords (quantity 4)
3 RJ-45 to DB-25 crossover adapter
4 RJ-45 to DB-9 crossover adapter
5 Printed documents
6 Antistatic wrist strap
7 Ethernet cables
8 Rackmounting kit
9 Cable management assembly
10 Rack card
11 Shipping brace
SPARC T5-8 Server
Getting Started Guide

2
▼Prepare the Server
1. After you remove the server from the box, place it on a mechanical lift if one is available.
Caution – Do not attempt to move the server alone without a lift. At a minimum, the main
components must be removed, and two people are required to move the server without a lift.
2. Remove all of the processor modules, the main module, the power supplies, the fans, and the PCIe
carriers.
For instructions on how to remove these components, refer to the SPARC T5-8 Server Service Manual.
3. Install any PCIe adapters that need to be installed in the PCIe carriers.
For instructions on how to install these components, refer to the Sparc T5-8 Server Service Manual.
4. Install the installation brackets onto the rack.
For instructions on how to install the brackets, refer to the SPARC T5-8 Server Installation Guide.
▼Install the Server
Caution – Do not apply power until instructed to do so. – To properly configure the host server and
view service processor (SP) messages, do not apply AC power to the server until you make the SP and
host networking connections, as described in this guide.
For rackmounting and cable management arm instructions, refer to the SPARC T5-8 Server Installation Guide.
1. Install the server in its intended location.
2. Replace all of the components that you removed.
For instructions on how to install these components, refer to the Sparc T5-8 Server Service Manual.
3. Connect a terminal device between the server’s SER MGT port and a terminal device.
This connection provides the initial communication with the SP. You must configure the server to
communicate using 9600 baud, 8 bit, no parity, 1 stop bit. For DTE-to-DTE communication, use the supplied
RJ-45 crossover adapters with a standard RJ-45 cable to set up a null modem configuration.
4. (Optional) Connect an Ethernet cable between the server’s NET MGT port and the network to which
future connections to the SP and host will be made.
Configure the system for the first time through the SER MGT port. After the initial configuration, you can set
up communication between the SP and host through this Ethernet interface.
5. Connect an Ethernet cable between one of the server’s NET ports and the network to which the server
will communicate.

3
6. Connect the power cords to the power supplies and to separate power sources.
When the power cords are connected, the SP initializes, and the power supply LEDs light. After a few
minutes, the SP login prompt displays on the terminal device. At this time, the host is not initialized or
powered on.

4
7. At the terminal device, log in to the SP as root with a password of changeme.
After a brief delay, the Oracle Integrated Lights Out Manager (Oracle ILOM) prompt is displayed. For
optimal security, change the root password. For more information about administration tasks such as
changing passwords, adding accounts, and setting account privileges, refer to the SPARC T5 Series Servers
Administration Guide and the Oracle ILOM documentation.
Note – By default, the SP is configured to use DHCP to obtain an IP address. If you plan to assign a static IP
address to the SP, refer to the SPARC T5-8 Server Installation Guide for instructions.
8. Power on the server and redirect the host output to display on the serial terminal device.
The server initialization might take several minutes to complete.
To cancel the initialization, press the #. (Hash+Dot) keys to return to the Oracle ILOM prompt. Then, type:
stop /System
9. (Optional) Execute other Oracle ILOM commands while the server initializes.
a. To display the Oracle ILOM prompt, press the #. (Hash+Dot) keys.
b. To see information about Oracle ILOM commands, type: help
To see information about a specific command, type: help command_name
c. To return to displaying host output from the server initialization, type: start /HOST/console
10. When prompted, follow the onscreen instructions, and type the configuration information for your
system.
If you are not sure how to respond, accept the default and make changes later when the Oracle Solaris OS is
running. After you confirm the configuration information, the server reboots and displays the Oracle Solaris
login prompt.
SUNSP00144FAC732F login: root
Password: changeme
. . .
->
-> start /System
Are you sure you want to start /System (y/n)? y
-> start /HOST/console
Are you sure you want to start /HOST/console (y/n)? y
Serial console started.
. . .

5
11. Log in to the server.
You now can enter Oracle Solaris OS commands at the prompt. For more details, refer to the Oracle Solaris
OS man pages and documentation at:
http://www.oracle.com/goto/Solaris11/docs
http://www.oracle.com/goto/Solaris10/docs
Note – Consider using Oracle VM for SPARC, which is a preinstalled system virtualization feature that provides
a discrete logical grouping with its own operating system, resources, and identity within a single computer
system. You can run a variety of applications in different logical domains, and keep them independent for
performance and security purposes.
▼Check for Latest OS Updates, Patches, and Firmware
Some server features are enabled only when certain versions of patches or firmware are installed. Install the
latest available versions for the best performance, security, and stability.
1. Review the SPARC T5-8 Server Product Notes.
See “Related Documentation” on page 6.
This document describes important product dependencies and late-breaking information.
2. Download the latest available versions from My Oracle Support at:
https://support.oracle.com

6
Related Documentation
Feedback
Provide feedback on this document at: http://www.oracle.com/goto/docfeedback
Access to Oracle Support
Oracle customers have access to electronic support through My Oracle Support. For information visit http://
www.oracle.com/pls/topic/lookup?ctx=acc&id=info or visit http://www.oracle.com/pls/topic/
lookup?ctx=acc&id=trs if you are hearing impaired.
Documentation Links
All Oracle products http://docs.oracle.com
SPARC T5-8 server http://www.oracle.com/goto/T5-8/docs
Oracle ILOM http://www.oracle.com/goto/ILOM/docs
Oracle Solaris 11 OS http://www.oracle.com/goto/Solaris11/docs
Oracle Solaris 10 OS http://www.oracle.com/goto/Solaris10/docs
Oracle VM for SPARC http://www.oracle.com/goto/VM-SPARC/docs
Copyright © 2013, Oracle and/or its affiliates. All rights reserved.
Copyright © 2013, Oracle et/ou ses affiliés. Tous droits réservés
Part Number: E35080-04
Mfg. Number: 7078107
July 2013