The rechargeable battery inside your appliance is easy to remove for recycling.
At the end of the product’s life and prior to disposal, please remove the
rechargeable battery from the handle by following
the instructions below. During the below
operation, be sure to protect your eyes, hands,
fingers, and the surface on which you work.
1. Remove 2pcs rubber feet on the bottom
of the handle. (Like on Fig. 9)
2. Insert a screwdriver into the slot located at the
bottom of the handle and turn counter-
clockwise to release the bottom cap
(Like on Fig. 9)
3. Slide the water tank down off the device and
unscrew the two screws beside the suction
tube. (Fig. 10)
4. Open the top cover and put the inner out of
the unit, then unscrew all the screws of the
inner.(Fig. 11)
5. Cut off the battery line and pull out the batteries
from the inner.(Fig. 12)
Use the Smart Water Flosser
After using the appliance (Fig.8)
1. Open the water tank cap and
dispose of the water in the tank.
2. Press “On/Off” key to turn on the unit,
and drain the water inside the
appliance.
3. Press “On/Off” key again to turn off
the unit, and close the water tank cap.
4. Wipe the device with dry cloth.
Note:
To prevent bacteria from propagating,
make sure there is no remaining water
inside the unit. If you’re not going to use
the appliance for a long time, make sure
to wipe and dry the appliance before
storing it.
Maintenance
Water tank cap
Nozzle
Water suction tube
Tank
Main unit
Tank Troubleshooting
Problem Possible Cause Solution
It does not work
It only works for
a few minutes
even after
charging
Water pressure
is very low
Water does not
come out
Disposal
56 7
4
015015
Fig. 9
Fig. 10
Fig. 11
Fig. 12
1. Attach nozzle onto the unit. (Fig. 2)
2. Open the water tank cap to fill the tank
with water at which the temperature
does not exceed 40ºC. Close the cap.
(Fig. 3)
3. OR Slide the water tank down off the
unit, fill the tank with water at which the
temperature does not exceed 40ºC, then
attach the tank onto the unit. (Fig. 4)
4. Press the “Mode” key to select the mode
that you desire. You can also change the
working mode during the process of your
water flossing. (Fig. 5).
Normal: for normal cleaning.
Soft: for gentle cleaning of sensitive
gums.
Pulse: for cleaning and massaging the
gums.
5. Hold the unit in an upright position with
the nozzle tip pointing towards your
teeth.
6. Keep your mouth slightly opened so that
the water can flow out.
7. Press the “On/Off” key to start the water
flossing process.(Fig. 6)
• Directing the water jet flow at a
90-degree angle to the teeth and
gums.
• Directing the water jet slowly along
with the teeth.
• Directing the water jet along the gum
line with the nozzle tip at a 90-degree
angle to the gum tissue.
• Cleaning between the teeth and around
any braces, crowns, or bridgework
thoroughly.
8. Press the “On/Off” key and then press
the nozzle release button to replace other
nozzles as per your need. (Fig.7)
9. Once water flossing is completed, press
the “On/Off” key again to turn off the
device.
10. Switch off your device and place it in
the protected case after use.
Use only water or neutral cleaning agent to clean the device. Never use
caustic or abrasive agents (e.g., vinegar or lime scale removers), since
they may damage the device. Do not wash using hot water of over 50ºC.
Keep the device away from high temperature area and avoid direct sunlight.
1. Remove the dirt by wiping the unit. Use a cloth with liquid soap to clean
it and wipe it off using a dry cloth.
2. Do not submerge the main unit in water to clean.
3. Dry after washing with water.
Wipe off any grime and dirt with a cloth.
1. Wash with water and wipe with soft cloth.
2. Replace the nozzle every 6 months.
1. Wash with water and wipe with soft cloth.
2. Do not bend, pull or twist the water suction tube.
1. Wash with water and wipe with soft cloth.
2. Dry the tank when not using for a long period.
You’ve just purchased the
product or it has been left
unused for more than
3 months.
The battery has reached
the end of its life cycle.
Charge the unit for
at least 4 hours.
Contact service
center for support.
Charging time was
insufficient.
Charge the unit for
at least 4 hours.
There is dirt stuck in
the nozzle
The nozzle is deformed
There is dirt stuck in the
filter
Replace the nozzle
Clean the filter
The tank is empty
The appliance is tilted
too much while in use
You’ve just purchased the
product or it has been left
unused for a period.
Fill up tank
Use with the appliance
in a vertical state
Pull out the nozzle then
flush nozzle hole on the
body.
Pulse / CH
Insert
Slide
Down
Fig . 2
Fig . 3
Fig . 4
Fig . 5
CH
2
1
Fig . 6
Fig . 7
Fig . 8
If you have recycling questions, please contact
your local waste management office.
ORACURA Solutions Pvt Ltd,
6th Floor, Unit 1, Vidhani Kalpavruksha,
H233-2, MIDC, T.T.C. Industrial Area, Nerul.
Navi Mumbai 410706
Toll-Free : 1800-120-7201
WhatsApp : +91 77387 33700
