Clear Stem Protector
Han wheel
Straight Floor Stan
Stem Extension
Stem Gui es
Stem Gui e & Sli e Stopper
Sli e Gate
(Rising Stem, Open Frame)
Bevel Gear
In many cas s, th op rating floor l v l is locat d
substantially high r than th op ning. In ord r to b abl to
op rat th gat , st m xt nsions ar n c ssary.
St m guid s ar us d to limit th “unsupport d” l ngth of
th st m xt nsion in ord r to avoid any buckling failur .
Th st m guid has a UHWMPE guid to r duc friction
b tw n th guid and th xt nsion.
Non-Rising Stem Configuration
As standard, non-rising st m gat configurations ar us d
with s lf-contain d fram d signs. Th r for , th st m
xt nsion do s not support th axial load (only torqu ) and
l ss wall brack ts ar r quir d.
As a g n ral rul , a st m guid should b install d v ry 10
f t (3 m t rs) of unsupport d st m xt nsion.
Rising Stem Configuration
As standard, rising st m gat configurations ar us d with
op n-fram d signs. Th r for , th st m xt nsion has to
support th axial load wh n th gat is op rat d. In
cons qu nc , th us of st m guid s is critical to avoid any
buckling failur . As a g n ral rul , a st m guid should b
install d v ry 6 1/2 f t (2 m t rs) of unsupport d st m
xt nsion.
This s ction bri fly d scrib s th installation, op ration and
maint nanc of MU Slid Gat s. For mor d tail d
information pl as r f r to th IOM Manual.
Installation:
Orbinox MU Slid Gat s ar install d by m ans of anchor
bolts. D p nding on th siz and working conditions th y
shall b ith r of th m chanical or ch mical typ (s tabl
b low).
In ord r to avoid l akag b tw n th concr t wall and th
fram , Orbinox r comm nds th us of construction s alant
quival nt to Sikabond Construction S alant (200ml p r
m t r of op ning p rim t r).
Th minimum concr t str ngth shall b 3,000PSI
(20.7 MPa). Th tol ranc of th concr t construction
(flatn ss, l v ln ss and plumbn ss) shall b in
accordanc to ACI 117-10 standard.
For d tail d information about typ , siz and quantity of th
r quir d anchor bolts for installation, pl as r f r to th
not s on th “G n ral Arrang m nt Drawing”.
Maintenance an Operation:
Th Orbinox MU Slid Gat s n d practically no
maint nanc . Th st m should b k pt lubricat d and s als
should b r plac d if damag d. Th MU Slid Gat is
clos d by applying a clockwis rotation.
Applying xc ssiv forc on th op rator wh n closing th
gat may caus damag to th st m.
MU Size
Water Pressure Anchor Bolt Type
Recommen e (Hilti or equivalent)
MU BI-DIRECTIONAL
6” x 6” - 48” x 48”
(150mm x 150mm - 1000mm x 1000mm)
S ating and Un-S ating
(Bi-Dir ctional)
Stud Typ M chanical An-
chor Bolts and Bolt Typ M -
chanical Anchor Bolts
Hilti “Kwik 3”
and Hilti “HSL”
MU BI-DIRECTIONAL
52” x 52” - 80” x 80”
(1100mm x 1100mm - 2000mm x 2000mm)
S ating and Un-S ating
(Bi-Dir ctional) Ch mical Anchor Bolts Hilti “HVU”
MU UNI-DIRECTIONAL
52” x 52” - 80” x 80”
(1300mm x 1300mm - 2000mm x 2000mm)
S ating (Uni-Dir ctional) Stud Typ M chanical An-
chor Bolts Hilti “Kwik 3”
STEM EXTENSIONS
INSTALLATION, OPERATION AND MAINTENANCE (IOM)
OBXC 06-2013
MU-7
ORBINOX r s rv s th right to chang sp cifications without notic .
.orbinox.com
ORBINOX CANADA, ORBINOX USA, ORBINOX BRAZIL, ORBINOX SPAIN, ORBINOX UK, ORBINOX FRANCE, ORBINOX GERMANY, ORBINOX INDIA, ORBINOX CHINA, ORBINOX S.E.A.
MU
SLIDE GATES
MODEL
