Orbis CODITEL User manual

User manual
GSM COMMUNICATION INTERFACE
Read all instructions carefully
CODITELisacommunicationinterfaceinacontainerof4DINmodules,whichusesGSM
technologytoenabletheremotecontrolofelectricservicesinthehome.Theoutputrelay
canbecontrolledbysendingatextmessagefromyourmobilephoneorbyringinganenabled
telephoneservice,thussavingthecostofthetextmessage.Theinstrumentalsooffersthe
optionofreceivingatextmessageconfirmingactivation.
SAFETY WARNINGS
During the installation and operation of the device observe the following instructions:
1) The device must be installed by a qualifi ed person
2) The device is aimed to be used in household premises and similar environments
3) Do not use the device for purposes other than indicated
4) A two-pole disconnect device shall be provided as part of the building installation
5) A protection device against over-currents should be installed in the electrical system,
upstream of the device
6) When installing the device, carefully respect the wiring diagrams
7) Disconnect the device from the power supply before accessing to the terminals
8) Do not power or connect the instrument if any part of it is damaged
9) The use of a GSM device can cause interference with the functioning of electronic
devices non-screened from radiofrequency signals (electromedical devices, pacemakers,
hearing aids etc.)
10) In case of fault, do not service the device yourself but contact the after-sales service.
11) The device is aimed for use in place with over-voltage category III and pollution
degree 2, as per standards EN 61010-1.
TECHNICAL CHARACTERISTICS
• Powersupply:230V~(-10%÷+10%)50Hz
• Consumption:4VA
• Connection:
 −cableswithmax6mm2section
• Output
 − abistablerelaywithexchangecontact
 − breakingcapacity:8(5)A/250V~
• GSMDualBandmodule(900-1800MHz)
• SMA-Fconnectorforexternalaerial(includedinthebox)
• Youcanstoreupto100numbers
• SignalLEDs:
− Red LED for signalling the output relay status
 − Red/greentwotoneLEDforsignallingthedevicestatus
• Multipurposebuttonforinstrumentprogramming
• Operatingtemperature:0÷50°C
• Operatinghumidity:10÷90%noncondensing
• Storagetemperature:-10÷+65°C
• Protection:IP40
• Container:4DINmodules
INSTALLATION
• Inorderfortheinstrumenttooperate,asimcardenabledfortelephonetrafficneedstobe
inserted in the relative slot.
Note. Ensure that the power cables are disconnected before inserting the sim
card.
Remove the cover and use a sharp object to press the slot release mechanism, as illustrated
intheboxalongside:
Attention. The SIM should have the PIN code request and the answerphone
deactivated.
• OncetheSIMhasbeeninserted,powertheinstrumentbyconnectingthewiresasillustrated
inthe“connectiondiagrams”box.
 Thestatusofthedeviceissegnalatedbythebicolorled :
 OFF: system not fed
 BLINKINGRED:sim not inserted or pin code in activity
 FIXEDRED:GSM field insufficient
 FIXEDGREEN:startingsystem/networkresearch
 BLINKINGGREEN:connectedtoGSMnetwork
 QUICKLYBLINKINGGREEN:arrivingincommand(ringorsms)
 QUICKLYBLINKINGRED:programming mode active
• Onceithasbeenconnected,theinstrumentwillbecomefullyoperativewithinaround30
seconds,duringwhichtheinstrumentstatusLEDwillbeafixedgreencolour(thetime
neededtosearchforthenetworkandinitialisetheinstrumentmayvaryonthebasisofthe
GSMfieldinwhichtheinstrumentisinstalledandtheproviderused).
 Oncetheinitialisationphaseiscompleted,thegreenLEDwillstarttoflashwithafrequency
of1Hzandtheinstrumentwillbereadytoreceivecommandsviatextmessageoraringon
the telephone.
Note. If the device will be installed into a screened panel, it is possible to replace
the antenna included in the kit with an another one with 3 meters cable.
The longer antenna is available as optional. Ensure that the power cables are
disconnected before replace the antenna.
OPERATION
Reset the device
• Whenitisswitchedonforthefirsttimeandwheneveritisreset,theinstrumentwillbeset
withthedefaultparameters.Todoareset,switchonthedeviceandpressthekeyshortlyin
threeseconds.Theledrelativetotheoutputwillblinkforfewseconds.
Set the certified numbers
In order to use the instrument, it is necessary to begin by setting the number of admins and
theusernumbersenabled(ifany).Pressingthekeyforalongtime(atleast5seconds)allows
youtoentertheprogrammingmode,whereyoucanenable/disablethevarioustelephone
services.
• Setting the admin number
 Afterswitchingtheinstrumentonandaftereschreset,forthefirsttimeandhavingentered
programmingmode,thefirsttelephonenumberthatmakesacallwillautomaticallybe
configuredastheadminnumber.Theadminnumbercanbechangedlateronbysendinga
textmessagefromthecurrentadminnumberwiththecommand:
ADMIN [newadminnumber](thenewadminnumbermustbeininternationalformat
+39…)
If you lose the admin number, it can only be changed by forcing an instrument reset.
Toretrieveautomaticallyalltheusernumbers,seethesection“Simmanagment”.
• Setting the user number
 Theusernumberscanbeentered/removedsimplyviaatelephonecallwhentheinstrument
isinprogrammingmode.Thecaller’snumberwillbeentered/removedonthebasisof
whetheritisrespectivelynotpresent/presentinthephonebook.Aconfirmationtext
messagewillbesenttothecaller,indicatingthenumberoflocationsoccupiedoutofthe
totalnumberavailable.Alternatively,theusernumberscanbeaddedorremovedbysending
atextmessagefromtheadminnumberwiththecommands:
USERADD [list of numbers to be added]
USERDEL [list of numbers to be removed]
 Thenumberstobeaddedmustbeininternationalformat+39…andseparatedbyanempty
spacebetweeneachnumber.
Commands
 CODITELhasarelayoutputwhosestatusissignalledbyaredLED(onoutputON).
 Itispossibletoworkontheoutputasfollows:
 − withthekeyonthefrontpanel,whichcanbeusedtoforcetheoutputswitch.Theadmin
numbercansettheoutputactionafterpressingthekeywiththecommand:
OUTKEY [functionality]
  withfunctionalitythatcanassumethevalues:
 RING itreactsasitdoestoacallwhenthekeyispressed
 TOGGLEthekeyswitchestheoutputON/OFFinbistablemode
 BLOCKdisablesthekeyfunctionality(itisnotpossibletoaccessprogramming
modewheninthismode)
  Ifthevalueisomitted,thecurrentinstrumentstatuswillbetheresponse.
 − withtelephonecallfromanenablednumber.
  Theadminnumbercandefinetheactionoftheinstrumentwhenitreceivesacallby
sendingatextmessage.Thepossiblecommandsare:
RINGRISP [status]
withstatusthatcanassumethevalues:
 ONsendsatextmessageconfirmingactivationtothecaller
 OFFnoconfirmationtextmessagetothecaller
  Ifthevalueisomitted,thecurrentinstrumentstatuswillbetheresponse.
RINGCONTROL [status]
  withstatusthatcanassumethevalues:
 ONcontrolsthecallernumbertocheckwhetheritisenabled
 OFFdoesnotcheckthecallernumber(functionusedwhenyouwishto
temporarilyallowanynumbertocontroltheinstrument)
  Ifthevalueisomitted,thecurrentinstrumentstatuswillbetheresponse.
OUTRING [output status] [status permanence time] [time unit of measurement]
  inwhichtheparameterscanassumethefollowingvalues:
 output status ON,OFF,TOGGLE,DISABLE
 status permanence time maximum(232-1)seconds(optionalparameter)
 time unit of measurement sseconds,mminutes,hhours(optionalparameter)
  Examples:
  OUTRINGOFF10StherelayisturnedOFFfor10secondswhenthecallisreceived
  OUTRINGDISABLEtherelaydoesnotdoanythingwhenthecallisreceived
  OUTRINGTOGGLEtherelaychangesstatuswhenthecallisreceived
 − withtextmessagefromtheadminnumberoranothernumber(viapassword).
Thestructureforallthecommandsisasfollows:
  [password][separator][command][separator][parameter1][separator]..[parameterN]
  where:
  [password]numericalfieldofamaximumof8figures
[separator] comprised of one or more space characters
[command] command recognised by the device
[parameter..] series of parameters relative to the command
The password field may be omitted if the command is given by the admin
number. Several commands may be included in one text message. In this case,
the commands executed will only be those whose response is contained in a
standard text message (160 characters). To enter numbers with the decimal
separator, you need to use a full stop.
 Thestructureofaresponsetoacommandissimilartothecommanditself,withtheaddition
ofthe“=”symboltoindicatethecurrentstatus.Forexample:
 OUTKEYBLOCKOUTKEY=BLOCK
 Inadditiontothoselistedabove,thecommandswhichcanbemadeviatextmessageare:
•Setting the output status
OUT [output status] [status permanence time] [time unit of measurement]
 where:
 output status ONorOFF
 status permanence time (232-1)seconds(optionalparameter)
 time unit of measurement sseconds,mminutes,hhours(optionalparameter)
 Iftheoutputstatusisomitted,theresponsewillbethecurrentinstrumentstatus.
 Example:
OUT ON 10 M outputONfor10minutes
•Setting the sending of a caller response message
OUTRISP [status]
 withstatusthatcanassumethevalues:
 ONenablesthesendingofatextmessageinresponsetothecaller
 OFFdisablesthesendingofatextmessageinresponsetothecaller
 Ifthestatusisomitted,theresponsewillbethecurrentinstrumentstatus.
 Example:
OUTRISP ON
•Displaying the output status and the settings
OUTINFO
 Apossibleanswearcouldbethefollowing:
OUT=ON OUTRING=ON 5s OUTRISP=ON RINGRISP=OFF OUTKEY=TOGGLE
 Itmeans:
 outputON,ONfor5secondswhenthecallisreceived,confirmationtothesmsabled,
confirmationtotheringdisabled,thekeyswitchestheoutputon/offinbistablemode.
•Changing the output name
OUTTXT [output label]
 Example:
OUTTXT valvola assigns to the output the name valvola
A string of a maximum of 10 characters with no spaces can be assigned as a
name. To restore the original name, just write OUTTXT NO. If an alternative
name is defined for the output, this name can be used instead of OUT1.
For example:
valvola ON 10 M activeoutput(valvola)for10minutes
•Enabling the forwarding function(foradminsonly)
FORWARD [number]
 It’spossiblesetanynumber.Inthiscase,thesmsthatnocontaincommandforthedevice
areforwardtothenumberspecified.Ifnotmodified,thenumberthatreceivedtheunknown
sms is the admin.
FORWARD OFF disabled this function.
 Example:
FORWARD [phone] forwardtothe11111234567numberthesms
that no contain commands
•Password management(foradminsonly)
PASS[newpassword]withnewpasswordwithamaximumof8figures
 Example:
PASS 12345678
• Simcardmanagment(foradminonly)
STORE copy in sim card all the number saved in the device
RESTORErestoreonlythenumberssavedwiththecommandSTORE
 Thesecommandsareparticularyusefulinthecaseofreset,withconseguentlossoftheuser
numbers saved in the device.
 Forthis,werecomandyoutodoaSTOREwhenallthenumbersareabilitated.
REFERENCE STANDARDS
ConformitytotheEUdirective:
1999/5/CER&TTE
declaredinreferencetotheHarmonisedStandards:
Safety:EN60950-1
Electromagnetic compatibility:EN301489-1andEN301489-7
DIMENSIONS
CONNECTION DIAGRAMS
DEFAULT SETTING
GATE-OPENER FUNCTION
OUT 1
8 A / 250 V ~
127 8 9
Password 12345678
Relay output status OFF
ADMINnumber Undened
USERnumbers Not defined
Callercontrol Active
Automaticcallanswer Disabled
Response to sms commands Active
Forwardunknownsms Active
• TouseCODITELasgate-openerisenoughinsertasimcard,feedsupplypowerthe
instrumentandwaitforthegreenledtoflash.Pressthebuttonforatleast5secondsto
enter in the programming mode.
 Makearingfromatelephonenumberwhichwillbeconfiguratedasadminnumber.
 Fromthisnumber,sendamessagecontainingthelistofnumbersthattobeabilitated
asgate-openermode,bythecommand:
USERADD [list of numbers to be added]
 Thenumberstobeaddedmustbeininternationalformat+39…andseparatedbyan
emptyspacebetweeneachnumber.Ifthemessageislongerthan160characters,divide
it in more sms.
 Numbersarenowabilitatedtoopenthegate.
Note. CODITEL sends an impulse of 2 seconds to the unit gate-opener.
To modify the duration of the impulse, see the OUTRING command.
72 6
45 87
0
Out
ON
SET
CODITEL
499-010