Orbit B-hyve User manual

FLOOD
SENSOR
Need Help?
If you encounter a problem, please use the following resources
before returning your B-hyve to the store.
Scan the QRCode for access to updated user manuals in
additional languages, videos, and more.
Instructions available in
additional languages online.
[e-mail]
email us
call us
1-801-299-5555
text us
801-905-8220
QUICK SET UP GUIDE
More information
on back
1) Requires a B-hyve Gen 2 Hub.
2)Remove Pull Tab from sensor.
3)Add new device in B-hyve app.
KEEP FOR YOUR RECORDS
BACK INSIDE
FRONT
LED
Status Light
CR
Battery Location
CR2032 3V
Retrieval Cord
Pairing
Reset
Button
Water Sensors
MACID
XXXXXXXXXXXX
1) Open the B-hyve™ App
Log into your B-hyve account and tap “My B-hyve”.
Go to “devices” then “add device”. Tap “Flood
Sensor” and the app will walk you through the rest of
the process.
For new users, search apps for “B-hyve” and
download the free Android or iOS app. Create
an account to begin setup.
2) Power and Pair Sensor
Remove the pull tab to activate the battery, your
sensor is now in pairing mode.
If at any time you need to re-pair, quickly press
the on the back of the sensor 5 times.
Sensors include one Lithium CR2032 battery.
Annual battery replacement is recommended for
optimal performance. See the “Replacing the Battery”
section for instructions.
3) Select Sensor Location
Place the sensor in an indoor location within range of
your hub. Range is approximately 300 ft, walls and
other interference can reduce this range. Position the
retrieval cord for easy extraction when placing a sensor
beneath heavy objects.
If using as a water sensor:
• Place the sensor flat on the floor in the area you wish
to monitor.
• Ensure that the flood sensor is positioned with its flat
surface faced down.
If using as a heat/cold sensor:
• Place in the location where you wish to detect
changes in temperatures.
• Avoid areas where inconsistent temperatures are
common. (near vents, exhausts, etc.)
The sensor communicates with the hub via
Bluetooth™; the range between the sensor and
hub will vary depending on the number of walls
and types of obstacles the signal needs to travel
through.
Avoid areas where the signal must travel
through dirt or thick steel barriers.
If water is detected or there is a temperature
fluctuation, a beep will play and a notification
will be displayed on your phone. Once the
problem is fixed, just reset your sensor and use
it again.
4) Complete Setup
Continue to follow the instruction within the app to
complete the setup process.

Specifications
Sensor
HVIN: FS
Part No – 71003, 71000, 04133
FCCID:MLFS
IC:3330AFS
RATING: DC 3.3V
Battery: CR 2032 Lithium (Non-Rechargeable)
Temp Range: 32-158°F (0-70°C)
Limited Warranty
Limited Orbit Irrigation Products LLC., (hereinafter Orbit)
warrants this product will be free from defects in material and
workmanship for a period of one year from the date of purchase.
Proof of Purchase (copy of your original receipt, purchase order or
invoice), the date the product was purchased and installation date
is required. During the warranty period, Orbit, will replace, free of
charge, the part or parts found to be defective under reasonable
use and service, as determined solely by Orbit. Orbit reserves
the right to inspect the defective part prior to replacement.
Liability under this warranty is limited to the replacement or repair
of defective parts. This warranty is exclusive and is in lieu of all
other warranties expressed or implied, including, but not limited to
warranties for fitness, for use or merchantability.
FCC and ICStatement
This device complies with Part 15 of the FCCRules and Industry
Canada license exempt RSS standards. Operation is subject to
Replacing the Battery
• Insert a flathead screwdriver into the open slot.
• Turn the screwdriver 90º to snap open the cover.
• To remove the battery, lift on the edge
of the coin cell battery using
your fingers. DO NOT use a
screwdriver or other metal object.
• Insert a new CR2032 battery at an angle.
• Verify that the + side is up.
• Reinstall the battery cover by snapping it into place.
Always completely secure the battery compartment. If
the battery compartment
does not close securely, stop using the product, remove
the batteries, and keep it
away from children.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention. Even used cells may cause injury.
CAUTION: Dispose of used
batteries according to the battery
manufacturer’s instructions.
WARNING:
Risk of Fire, Explosion, and Electric Shock. Replace
battery with CR only. Use of a different battery
has the potential for a risk of fire, explosion, and
electric shock.
WARNING:
Do not ingest batteries. Chemical Burn Hazard. Keep
batteries away from children.
WARNING:
This product contains a lithium button/coin cell battery.
WARNING:
If a new or used lithium button/coin cell battery is
swallowed or enters the body, it can cause severe
internal burns and can lead to death in as little as 2
hours.
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
FCCWarning: Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCCRules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This device meets the FCC and IC requirements for RF exposure
in public or controlled environments. The end user is advised to
maintain a distance of 20 cm from
the controller and any personnel to ensure compliance with RF
exposure regulations. This Class B digital apparatus complies with
Canadian ICES-003.
Déclaration de FCC et l’IC
Cet appareil est conforme à la section 15 de la Règlementation de
la FCC et la norme RSS d’Industry Canada. Son fonctionnement
est soumis aux deux conditions suivantes: (1) cet appareil ne doit
pas causer d’interférences nuisibles, et (2) cet appareil doit tolérer
toutes les interférences, dont les interférences pouvant causer un
fonctionnement non désiré.
Cet appareil numérique de classe B est conforme à la norme
canadienne ICES-003.
Remarque: cet appareil été testé et déclaré conforme aux limites
d’exposition pour les appareils numériques de classe B, selon
la section 15 de la Règlementation de la FCC. Ces limites
sont conçus pour fournir une protection raisonnable contre
les interférences nuisibles dans une installation résidentielle.
Cet appareil produit, utilise et peut émettre de l’énergie radio
fréquence et, si elle n’est pas installée et utilisée conformément
aux instructions, peut causer des interférences nuisibles aux
communications radio. Cependant, il n’est pas garantie que
des interférences ne se produisent pas dans une installation
particulière. Si cet appareil cause des interférences gênantes à
la réception d’un signal radio ou de télévision, ce qui peut être
déterminé en allumant et en éteignant l’appareil, l’utilisateur peut
corriger les interférences en suivants une des mesures suivantes :
• Réorientez ou repositionnez l’antenne de réception.
• Augmentez la distance entre l’appareil et le récepteur.
• Branchez l’appareil dans une prise sur un circuit différent du
circuit sur lequel le récepteur est branché.
• Consulter le revendeur ou un technicien radio/TV expérimenté
pour obtenir de l’aide.
Cet appareil est conforme aux exigences de la FCC et de l’IC
concernant l’exposition aux ondes dans un environnement public
ou contrôlé. Il est conseillé à l’utilisateur final de maintenir une
distance de 20 cm du contrôleur pour assurer la conformité aux
réglementations d’exposition RF. Information de conformité pour
le Canada.
Orbit®
PO Box 328
Bountiful, UT 84011-0328
USA
PN 71000-24 rA