Organized Living freedomRail 3 Drawer Big OBox User manual

Top
(44)
freedomRail Assembly Instructions
3 Drawer Big OBox
Euroscrews
(6) (14)
(4)
Connector
Bolts
Hanging
Brackets
Wood
Screws
Bottom
Top
Handles
(3)
Machine Screws
(For Handles)
1 Large Drawer
right Side
3 Drawer Bottoms
2 Small
Drawer
Right
2 Small Drawer Fronts
(1) Large Drawer Front
2 Small
Drawer
Left
(6) Full Extension Drawer Glides
Assembling the 3 Drawer Big OBox
Step 1: Attach Hanging Brackets
Left Side Right Side
Back Edge Back Edge
Attach Hanging Brackets to Sides using Euroscrews. (If using Power Drill, set torque to low setting.)
Step 2: Install Connector Bolts
Top and Bottom
Smaller Holes for
Connector Bolts
Install (4) Connector Bolts into small holes on Top and Bottom Panels.
Step 3: Attach Sides
Cam
Lock
Open
(a) Attach Sides to Bottom. (b) Tighten Cams by turning clockwise until snug.
Step 4: Attach Top
1
Over
Contents of Package
(6)
(1) Large
Drawer Left
Side
(1) Large
Drawer Right
Side
Top
(3) Drawer Bottoms
(2)
Small
Drawer
Left
Sides
(2)
Small
Drawer
Right
Sides
1⁄"
(2) Small Drawer Fronts
(1) Large Drawer Back
Proper Care for an OBox: Use Goo Gone™ or Simple Green® with a rag or putty knife to remove any excess glue or marring that was caused by shipping or assembly.
(2) Small Drawer Backs
Tools Required
Power Drill
#2 Phillips
Screwdriver
#2 Phillips Driver
(a) Attach Top. (b) Tighten Cams by turning clockwise until snug.
Left Side
Right Side

123
©2015 Organized Living
Bloomington, IN 47403
OrganizedLiving.com
1-800-669-3225
June 2015
880151
Installing Glides
freedomRail Assembling Instructions
3 Drawer Big OBox
Bumper
Outer Glide Black Tab Inner Glide
Step 5: Seperate Glide
(a) Pull out Inner Glide to expose Black Tab.
Attaches to Drawer
Attaches to Big OBox
(b) Seperate Inner Glide from Outer Glide by pushing the Black tab while pulling Glide sections apart.
Step 6: Attach Outer Glides to Big OBox
Bumper
Big OBox Front
Turn Big OBox on its side. Attach outer Glides with (6) Euroscrews in holes
1, 2, and 3 Repeat for other side.
.
Step 7: Mount Big OBox on Uprights
Mount Big OBox onto Uprights by inserting Hanging Brackets into the innermost track of each Upright.
Two people recommended for installation.
Assembling/Inserting Drawers
(a) Attach Sides to Back. (b) Secure with 1⁄" Wood Screws. (c) Slide in Bottom.
Step 9: Attach Front Panel Connectors
Step 10: Attach Drawer Glides & Handles
Notched
End
(a) Lock Cam by turning clockwise ¼ turn. Turn until snug.
(b) Attach Inner Glides to Drawer with Euroscrews. Notched End should be at back.
(c) Attach Handle with Machine Screws.
(a) Position Drawer on Glides and push in Drawer completely.
Repeat Steps 8, 9, 10, and 11 for (2) Small Drawers.
NOTE: To remove Drawers, push the Black Tab while pulling out the Drawer.
Screw in Connector Bolts and attach Front.
2
Step 11: Insert Drawers
Step 8: Attach Drawer Panels and Drawer Bottom