Oricom TPS10 User manual

Keep this user guide for future reference. Always retain your proof of
purchase in case of warranty service.
www.oricom.com.au
Tutorial videos are available -oricom.com.au,
select your model and scroll down to FAQ's
Operating Instructions
TPS10 External Tyre Pressure
Monitoring System

2
This unit complies with all relevant Australian
and New Zealand approval requirements
AS/NZS 4268:2017

Table of Contents
3
Pack Includes ............................................................ 4
Controls and Indicators.............................................. 5
Installation ................................................................. 6
Sensor Installation..................................................... 7
Functional Testing ..................................................... 8
Alerts and Indicators.................................................. 9
Settings.................................................................... 10
Sensor Re-Programing............................................ 17
Sensor Battery Replacement................................... 20
Specications .......................................................... 21
WARNINGS............................................................. 22
Express Warranty (Australia)................................... 24
Need Help?
If you need assistance setting up or using your Oricom product now or in the
future, call Oricom Support.
Australia [phone]
www.oricom.com.au
Mon-Fri 8am – 6pm AEST
New Zealand 0800 67 42 66
www.oricom.co.nz
Mon-Fri 10am – 8pm NZST

4
Pack Includes
Pack Includes
LCD Display
Sensor X4 or X6
Washers X5 or X7
(1 spare)
Nuts X5 or X7
(1 spare)
Dustproof cover X4 or X6
Anti-slip mat X1
Sensor tool X1
Spanner X1
Ensure that these parts are stored safely.

5
Controls and Indicators
Controls and Indicators
Psi
Psi Psi Psi
Trailer interface Spare interface
Tow vehicle interface
Select button
Display battery indicator
Temperature data
SET button
Solar panel
Ventilation holes
Micro USB input
Charging status
Pressure data
Axles of trailer
Temperature unit
Pressure unit
Warning indicator
Note: The icon in the centre of the LCD display indicates the viewing interface.

6
Installation
Display Installation
Powering On/Off The Display
Press any button for 3 seconds to turn the display on.
Press " " button for 3 seconds to turn the display off.
Note: The display unit is solar powered, you can charge the display battery via
USB power if required.
Psi
Installation Position
USB Charging Connection
USB power cable
(Not included)
The drawing to the right indicates a suitable mounting position for your display unit.
To avoid the display unit moving whilst travelling, place the anti-slip mat underneath the display unit.

7
Sensor Installation
Sensor Position
Sensor Installation
Sensor position
Psi Psi Psi
F.L. F.R.
R.L. A3R.R.
A1 A2 S1 S2
A4
F.R. R.R.
R.L.
F.L.
A2 A4
A3
S2 S1
A1
Note: Typical sensor position as
per diagram to the left.
1.Unscrew the valve cap. 2.Insert the dustproof cover onto the valve stem.
3.Screw on the nut. 4.Screw on the sensor.
Note: Axle B not in use
Note: Depending on pack purchased you may have up to 10 sensors.
Tow Vehicle Trailer Spares
Note: Do not over-tighten sensors as this will effect the readings.

8
Functional Testing
Functional Test After Installation
5. Tighten up the nut to the sensor by using
the spanner.
6. Check for air leaks by spraying soapy water.
Once installation is complete, drive the vehicle to a speed over 25Kph to start receiving real time tyre
data. Spare tyre and trailer sensors update periodically or when there is a pressure change.
The installation is complete when all tyre data has been received and is showing on the display.
Note: Do not over-tighten sensors as this will effect the readings.

9
Alerts and Indicators
Alerts
High temperature
Psi
3 Beeps, tyre and pressure flashing
Display low battery
Battery indicator flashing
Psi
3 Beeps, tyre and pressure flashing
Psi
3 Beeps, tyre and pressure flashing
Psi
Psi
Psi
5 Beeps, tyre and pressure flashing "LO" replace battery
Psi
Sensor failure
5 Beeps, tyre and pressure flashing "--" displayed
Psi
3 Beeps, tyre and temp flashing

10
Settings
Settings
To Enter/Exit The Setting Menu
To enter the menu, press and hold " " button for 4 seconds, until you
hear a beep.
To exit the menu, press and hold " " button for 4 seconds, until you hear
two beeps.
Menu options:
Pressure unit
Temperature unit
Time interval of
each interface
High pressure
value
Low pressure
value
High temperature
value
Disable/enable trailer
and spare tyres
Tyre data
deletion
Note: The display automatically exits the menu when left inactive for 3 minutes.
Note: Please visit our website to view tutorial videos on how to
enter / exit settings, Visit www.oricom.com.au select your model
and scroll down to the FAQ's section.

11
Settings
Pressure Unit Setting:
To access the Pressure Unit setting (Bar or Psi), press the " " button to
select Psi or Bar then press the " " to save and enter the next setting.
Psi
Temperature Unit Setting:
To access the Temperature Unit setting (degrees Celsius / Fahrenheit),
press " " button to select the °C or °F, then press " " to save and enter
the next setting;
Time Interval Setting For Each Interface:
To access the Time Interval setting, press " " button to set the time
interval for each interface, then press " " button once to enter the next
setting.
Time intervals (seconds): 5 / 10 / 20 / 30 / 60 / OFF
Default: 5 seconds
Note: This setting is the time each interface is displayed for (tow vehicle /
Trailer / Spares)

12
Settings
High Pressure Value Setting:
• Pressthe" " button to set the high pressure value of the current
interface.
• Press" " to save and enter the next setting.
Note: When more than 4 sensors are connected you can set the high
pressure value for the individual interfaces (Tow vehicle / Trailer / Spare) to
do this, whilst in the high pressure value setting:
1. Press the " " button to set the high pressure value of the current
interface.
2. Press and hold the " " button and press the " ". The image on the
display will change from the tow vehicle to the trailer.
3. Press the " " button to set the high pressure value for the trailer.
4. Press " " to save and enter the next setting.
Note: To change the high pressure setting for the Spare Tyre Interface,
repeat steps 2 and 3.
Press " " button once to enter the next setting.
Psi
Psi Psi Psi
Trailer interface Spare interface
Interface

13
Settings
Low Pressure Value Setting:
• Pressthe" " button to set the low pressure value of the current
interface.
• Press" " to save and enter the next setting.
Note: When more than 4 sensors are connected you can set the low
pressure value for the individual interfaces (Tow vehicle / Trailer / Spare) to
do this, whilst in the low pressure value setting:
1. Press the " " button to set the low pressure value of the current
interface.
2. Press and hold the " " button and press the " ". The image on the
display will change from the tow vehicle to the trailer.
3. Press the " " to set the low pressure value for the trailer.
4. Press " " to save and enter the next setting.
Note: To change the low pressure setting for the spare tyre interface,
repeat steps 2 and 3.
Press " " button once to enter the next setting.
Psi

14
Settings
High Temperature Value Setting:
• Pressthe" " button to set the high temperature value of the current
interface.
• Press" " to save and enter the next setting.
Note: When more than 4 sensors are connected you can set the high
temperature value for the individual interfaces (Tow vehicle / Trailer / Spare)
to do this, whilst in the high temperature value setting:
1. Press the " " button to set the high temperature value of the current
interface.
2. Press and hold the " " button and press the " ". The image on the
display will change from the tow vehicle to the trailer.
3. Press the " " to set the high temperature value for the trailer.
4. Press " " to save and enter the next setting.
Note: To change the high temperature setting for the spare tyre interface,
repeat steps 2 and 3.
Press " " button once to enter the next setting.
Note: Please visit our website to view tutorial videos on how to set
value settings, Visit www.oricom.com.au and select model and
scroll down to the FAQ's section.

15
Settings
To Disable/Enable Trailer and Spare Tyres:
Press " " button to select Trailer or Spare Tyre interface, then press and
hold " " button for 3 seconds to disable or to enable.
Press " " button to save and enter the next setting.
Trailer axles setting:
Spare tyre settings (individual):
Enabled status (default) when trailer connected.
Enabled status (default) all spare tyre sensors turned on.
Disabled status spare tyre sensor turned off.
Disabled status when trailer not connected.
Note: Please visit our website to view tutorial videos on how to
disable / enable sensors, Visit www.oricom.com.au select your
model and scroll down to the FAQ's section.

16
Settings
Sensor Deletion:
To access the sensor deletion setting, press " " button to select the
programmed tyre data to be deleted.
Psi
Then hold " " button until the display shows "--", the sensor data has
been deleted.
Psi
Press " " button to select next sensor or " " button to save.
To exit the menu: Press and hold the " " for 4 seconds, you will hear 2
beeps conrming you have exited the menu.
Note: Please visit our website to view tutorial videos on how to
delete sensors, Visit www.oricom.com.au select your model and
scroll down to the FAQ's section.

17
Sensor programming
Sensor programming
Note: Sensors in 4 and 6 packs come programmed, Additional twin sensor
packs purchased will need to be programmed
When programming a new sensor or a missing sensor to the display.
Enter Programming Mode:
Press " " button 5 times, the display will beep once to conrm you are
now in sensor programming mode.
Sensor Programming
Press the " " button to cycle through the sensors.
- once the desired sensor position is ashing you are ready for programming
that sensor.
Psi
Psi Psi Psi
Trailer interface Spare interface
Interface

18
Sensor programming
- Screw the sensor to the corresponding tyre.
- The pressure data will appear on the display, a beep will sound.
- Press the " " button to SAVE (IMPORTANT) a beep will sound.
Psi
- Press" " button to move to the next sensor and repeat the programming
steps listed above.
Psi
Psi
To exit the menu: Press and hold the " " button for 4 seconds, you will
hear 2 beeps conrming you have exited the menu.
NOTE: Do not program sensors to Axle B.

19
Sensor programming
NOTE:
• Towvehiclesensorscanonlybeprogrammedtothetowvehicleinterface.
DO NOT program Trailer or Spare sensors to tow vehicle interface and
vice versa.
• Sparetyredataisupdatedevery15minutesorifthereisasignicant
change in air pressure.
• Displaydimsandbrightensdependingonthelightconditionssensedby
the solar panel.
• DONOTprogramsensorstoAxleB.
• Thetyredatacanbeclearedbyperformingareset,pressandholddown
both buttons for 3 seconds, the screen should clear the tyre pressure
readings and "--" will appear on the screen. Once driving the tyre
pressures will display automatically.
NOTE: Please visit our website to view tutorial videos on how to
program sensors to the control unit, Visit www.oricom.com.au
select your model and scroll down to the FAQ's section.

20
Sensor Battery Replacement
Sensor Battery Replacement
Note: Please visit our website to view tutorial videos on how to
replace sensor batteries, Visit www.oricom.com.au select your
model and scroll down to the FAQ's section.
1.Unscrew the nut. 2.Unscrew the sensor.
3.Take out the washer. 4.Unscrew the sensor cover by using
the sensor tool.
5.Replace the battery. 6.Repeat steps in “Sensor Installation”.