OrienTek TLS-35m User manual
TLS-35m stable light source instruction manual
Products introduction
Backlight control
Wavelength selection
Carrier output
The TLS-35 fiber optic light source is characterized by stable output
optical power, wavelength and spectral width with a small range of
stable changes. Provide single-mode fiber measurement
(1310nm/1550nm) dual-wavelength laser output and multi-mode fiber
measurement (850nm/1300nm) dual-wavelength laser output, and can
also provide single and multi mode (850nm/1300nm/1310nm/1550nm)
four-wavelength laser output And (1310nm/1490nm/1550nm)
three-wavelength laser output. Mainly used for FTTX network and fiber
optic testing. When combined with Optical power meter, it is used to
measure optical power and end-to-end optical loss.
3
9
8
4
5
6
12
11
10
7
2
OLS interface
1
LED lighting
2
Display
3
Enter key
4
LED key
5
On/off key: turn on or off the device
7
automatic shutdown
9
frequency
10
power supply battery
8
unit
11
wavelength
12
6
key
CW
1
Power-on and power-saving function settings
Auto-off
The equipment will turn on
after pressing the " " key. Press
this button again for more than
two seconds to shut down.
This instrument has power
saving function, normal there is no
operation for about ten minutes
after booting, The device will
automatically shut down. If you need
a screen Shield this function to keep
the equipment working all the time
Status, just short press "on" when
booting Key, "Auto-off" at the bottom
left of the meter display. Disappearing
means that the power saving function
is cancelled.
1310
270
CW
In the power-on state, the backlight will
automatically turn off after a period of
time. After turning off, press any key to
activate the backlight. The backlight is
used to illuminate the instrument display
at night or in dark places.
270
λ
1310nm
1550nm
According to the needs of the project, select
the corresponding wavelength to match the
optical power meter. After the meter is turned
on, press the "output wavelength" key, the
output wavelength and length will be
switched to the corresponding wavelength in
turn, and will be displayed on the display. The
laser light source of this series can provide
1310nm and 1550nm dual-wavelength laser
output according to demand.
1310
HZ
270 HZ
1000
HZ
2000
CW
In the actual project, it is necessary to load the
audio carrier in the optical signal to identify
the optical fiber. The equipment contains
three carrier frequencies, which are 270Hz,
1KHZ, and 2KHz. After pressing the "modulat-
ed carrier" key, the equipment will load
different carriers in sequence, and the display
will be displayed at the same time. The current
carrier frequency will be displayed on the
screen.
Contact us
Calibration function description
Products introduction
Tips
NANJING ORIENTEK OPTICAL COMMUNICATION LTD
Mail: [email protected]
Add: Jianshan Industry Park, Liuhe District, Nanjing, Jiangsu, China
Web: www.orientekot.com
TEL: +86 17312230635
Products specification
Press the "illumination" button to
turn on the LED lighting, which is
convenient for construction and
operation in a dark environment.
Output power -5dB
SM wavelength 1310nm/1550nm
MM wavelength 850nm/1300nm
PON wavelength 1310nm/1490nm/1550nm
Equipped with LED lights to facilitate work in
dark environments
Silica gel shell protection design, 2m anti-fall
SM&MM wavelength 850nm/1300nm/1310nm/1550nm
2.5mm universal interface + SC adapter
Wavelength（nm）
Output Power -5dB
Optical connector SC+2.5mmuniversal（1.25mm LCoptional）
Power supply Alkaline batteries(3 AA 1.5V batteries))
Stable output ±0.05dB/15mins; ±0.1dB/ 8小时
Modulation frequency CW, 270Hz, 1KHz, 2KHz
volume and weight
1310+1550nm（TLS-35-S)
850+1300nm（TLS-35-M)
850+1300+1310+1550nm（TLS-35-MS)
1310+1490+1550nm（TLS-35-PON)
160x85x45mm / 220g
Operating environment altitude:
areas below 2000m above sea level
Use environment
Please read all instructions and warnings before
using this product. Irregular use will cause
It will damage the product or personal safety.
1） Do not store this product in high temperature, strong light
and strong magnetic field environment, do not put it pace in
other harsh environments such as fire sources.
2）Improper use of the product may easily cause the product
itself or may endanger personal property Safety.
3）If the consumer violates the product manual and improper
use, the personal and financial Property damages will bear all
consequences, and the company will not bear any legal
responsibility.
4）Non-professionals are strictly forbidden to decompose
this product.
5）Avoid using electrical appliances or loads that exceed the
output current of this product (the circuit will protect
Protection, no output).
6）Avoid strong physical effects, including knocking, throwing,
trampling, squeezing, etc.
Packing carton, stable light source,
certificate, instruction manual
Standard kit
Interface
accessory SC FC ST
