ORing Industrial Networking Corp. RGPS-92222GCP-NP-LP User manual

Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
RGPS-92222GCP-NP Series
QIG RGPS-92222GCP-NP Series 1907-2-29-RGPS92222GCPNP-1.0
The , which consist of the
and models, are managed rack-mount
Ethernet switches with 22 10/100/1000Base-T(X) IEEE802.3at P.S.E.
ports, two Gigabit combo ports, and two 100/1000Base-X SFP ports. The
P.S.E-enabled ports are able to provide sufficient power for power-hungry
devices with up to 30w per port. With dual power inputs for redundancy,
the switches have an operating temperature from -40 C to 60 C.
RGS-92222GCP-NP series RGPS-92222GCP-
NP-LP RGPS-92222GCP-NP-P
oo
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
Dimension
Panel Layouts
1. Console port
2. Reset button
3. Power indicator
4. Ring status LED
5. RM status LED
6. Fault indicator
7. LAN ports
Front View
Rear View
Installation
Rack-mounting
Step 1:
Step 2:
Install left and right front mounting brackets to the switch using three screws on each side.
With front brackets orientated in front of the rack, fasten the brackets to the rack using two more
screws.
Network Connection
Console cable
Use the provided DB-9 cable (RS-232 cable) to connect the switch to a PC with the DB-9
connector attached to the switch console port and the DB-9 female connector to the PC.
PC pin out (male)
assignment
RS-232 with DB9
femal e connector
Pin#2RD Pin#2TD
Pin #3 TD Pin #3 RD
Pin #5 GND Pin #5 GND
Package Contents
Contents
QIG
CD
Console Cable
Screw (M4 X6)
Power cord
Rack-mounted
kit (L&R)
Number
X1
X1
X1
X6
X1
X1
RGPS-92222-
GCP-NP
Pictures
MANAGED
Rack-Mount
GIGABIT
SWITCH
PoE
Managed Gigabit PoE Ethernet Switch
X1
35.50
44.00
8.00 20.00
24.00
32.0
5.50
R3.25
25.50
2.50
4.30
17.80
30.20 82.00
342.00
86.5
ACPower SWITCH
49.0
3.0
AC100-240V
50-60HZ
PW1
44.00
431.00
G2 G4 G6 G8
G1 G3 G5 G7
LINK/ACT
Console
G23 G24 G25 G26
RGPS-92222GCP-NP
R.M.
Ring
Reset
10/100/
1000T
Fault
G1
G2
G7
G8
G9
G10
G15
G16
G17
G18
G23
G24
PoE
100/1000X
G10 G12 G14 G16
G9 G11 G13 G15
G18 G20 G22
G17 G19 G21 G23
G24
PWR
G2 G4 G6 G8
G1 G3 G5 G7
LINK/ACT
Console
G23 G24 G25 G26
RGPS-92222GCP-NP
R.M.
Ring
Reset
10/100/
1000T
Fault
G1
G2
G7
G8
G9
G10
G15
G16
G17
G18
G23
G24
PoE
100/1000X
G10 G12 G14 G16
G9 G11 G13 G15
G18 G20 G22
G17 G19 G21 G23
G24
PWR
1
2 3 4 5 6 7
8 9
10
11 12
13 14
8. LED for even Ethernet ports link/act status
9. LED for odd Ethernet ports link/act status
10. First Gigabit combo port
11. Second Gigabit combo port
12. PoE status LED for LAN ports
13. SFP ports
14. LNK/ACT LED for SFP ports
ACPower SWITCH
AC100-240V
50-60HZ
PW1
1 2
1. Power switch
2. AC power input (100V~240V
/ 50~60Hz)
The switch provides standard Ethernet ports. According to the link type, the switch uses CAT
3,4,5,5e UTP cables to connect to any other network devices (PCs, servers, switches,
routers, or hubs). Please refer to the following table for cable specifications.
Cable Types and Specifications:
Cable Type Ma x. Length Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm U TP UTP 100 m (328 ft) RJ-45
1000BASE-T Cat. 5 / Cat. 5e 100- ohm UTP UTP 100 m (328 ft) R J-45
With 10/100BASE-T(X) cables, pins 1 and 2 are used for transmitting data, and pins 3 and 6 are
used for receiving data. The device also supports auto MDI/MDI-X operation. You can use a
cable to connect the switch to a PC
For pin assignments for different types of cables, please refer to the following
tables.
10/100 Base-T(X) MDI/MDI-X
Pin Number MDI port MDI-X por t
1TD+(transmit)RD+(receive)
2TD-(transmit)RD-(receive)
3 RD+(recei ve) TD+(tr ansmit)
4NotusedNotused
5NotusedNotused
6 RD-(re ceive) TD -(transmit)
7NotusedNotused
8NotusedNotused
1000B ase-T MDI /MD I-X
Pin Number MDI port MDI-X port
1 BI_DA+ BI_DB+
2 BI _DA- BI_DB-
3 BI_DB+ BI_DA+
4 BI_DC+ BI_DD+
5 BI _DC- B I_DD-
6 BI _DB- BI_DA-
7 BI_DD+ BI_DC+
8 BI_DD- B I_DC-
10/100Base-T(X) P.S.E. RJ-45 por t
Pin Number Assignmen t
#1 TD+ wi th P oE Power input +
#2 TD- with PoE Power input +
#3 RD+ with PoE Power i nput -
#6 RD- with PoE Power input -
1000Base-T P.S.E. RJ-45 port
Pin Number Assign ment
#1 BI_DA+ wit h PoE Power input +
#2 BI_DA- wit h PoE Power input +
#3 BI_DB+ with PoE Power input -
#4 BI_DC+
#5 BI_DC-
#6 BI_DB- with PoE Power input -
#7 BI_DD+
#8 BI_DD-

QIG Quick Installation Guide
PRINTED ON RECYCLED PAPER
Version 1.0
Quick Installation Guide
Configurations
After installing the switch and connecting cables, start the switch by
turning on power. The green power LED should turn on.
LED indication table
1. Launch the Internet Explorer and type in IP address of the switch. The
default static IP address is 192.168.10.1
2. Log in with default user name and password (both are ). After
logging in, you should see the following screen. For more information
on configurations, please refer to the user manual. For information on
operating the switch using ORing’s Open-Vision management utility, please
go to ORing website.
admin
Resetting
To reboot the switch, press the button for 5 seconds.
To restore the switch configurations back to the factory defaults, press the
button for 10 seconds.
Reset
Reset
Specifications
ORing Switch Model
Physical Ports
Technology
Ethernet Standards
LED Indicators
10/100/1000Base-T(X) with
P.S.E.PortsinRJ45Auto
MDI/MDIX
RS-232 Serial Console Port
Switch Properties
Security Features
Device Binding security feature
Enable/disable ports, MAC based port security
Port based network access control (802.1x)
Single 802.1x and Multiple 802.1x
MAC-based authentication
QoS assignment
Guest VLAN
MACaddresslimit
TACACS+
VLAN (802.1Q) to segregate an secure network traffic
Radius centralized password management
SNMPv3 encrypted authentication and access security
Https / SSH enhance network security
Web and CLI authentication and authorization
Authorization (15 levels)
IP source guard
Software Features
IEEE 802.1D Bridge, auto MAC address learning/aging and MAC address (static)
Multiple Registration Protocol (MRP)
MSTP RSTP/STP compatible)
Redundant Ring (O-Ring) with recovery time less than 30ms over 250 units
TOS/Diffserv supported
Quality of Service (802.1p) for real-time traffic
VLAN (802.1Q) with VLAN tagging
IGMP v2/v3 Snooping
IP-based bandwidth management
Application-based QoS management
DOS/DDOS auto prevention
Port configuration, status, statistics, monitoring, security
DHCP Server/Client
DHCP Relay
Modbus TCP
DNS client proxy
(
Network Redundancy O-Ring, Open-Ring, O-Chain, MRP, MSTP (RST/PSTP compatible)
RS-232 in DB-9 connector with console cable. 115200bps, 8, N, 1
RGPS-92222GCP-NP-LP
22
IEEE 802.3 for 10Base-T, IEEE 802.3u for 100Base-TX and 100Base-FX,
IEEE 802.3z for 1000Base-X,
IEEE 802.3ab for 1000Base-T,
IEEE 802.3ae for 10Gigabit Ethernet
IEEE 802.3x for Flow control,
IEEE 802.3ad for LACP (Link Aggregation Control Protocol )
IEEE 802.1p for COS (Class of Service)
IEEE 802.1Q for VLAN Tagging
IEEE 802.1w for RSTP (Rapid Spanning Tree Protocol)
IEEE 802.1s for MSTP (Multiple Spanning Tree Protocol)
IEEE 802.1x for Authentication
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol)
IEEE802.3atPoEspecification(upto30WattsperportforP.S.E.)
RGPS-92222GCP-NP-LP : Total power budget is 320Watts
RGPS-92222GCP-NP-P : Total power budget is 720Watts
Switch latency: 7 us
Switch bandwidth: 48Gbps
Max. Number of Available VLANs: 256
IGMP multicast groups: 128 for each VLAN
Port rate limiting: User Define
MAC Table 8K
Processing Store-and-Forward
Priority Queues 8
Amber : Indicate unexpected event occurred
Fault Indicator (Fault)
O-Ring Indicator (Ring)
Green:FlashingtoindicatesystemoperatedinO-RingMastermodeRing Master Indicator (R.M.)
Green : Indicates that the system operating in O-Ring mode
Green Blinking : Indicates that the Ring is broken.
Jumbo frame Up to 9.6K Bytes
Green : Power indicatorPower Indicator (PWR1/PWR2)
10/100/1000Base-T(X) RJ45
Port Indicator
Power
Power consumption(Typ.) 37 Watts (P.D. not included)
Overload current protection Present
Green for Link/Act indicator at 1Gbps
Amber for Linl/Act indicator at 10/100Mbps
PoE Indicator Green:PoEenabledLEDx24
100/1000Base-X SFP Port
Indicator Green:forSFPLink/Actindicator
Overload current protection 100~240VAC with power socket
Environmental
-40to85C(-40to185F)
oo
Storage Temperature
Operating Temperature
Physical Characteristic
Dimension(WxDxH)
Weig ht (g )
5000g
5% to 95% Non-condensing
Operating Humidity
Regulatory Approvals
Enclosure 19 inches rack mountable
5730g
431(W)x342(D)x44(H)mm(16.97x13.47x1.73inches)
FCC Part 15, CISPR (EN55022) class AEMI
EN61000-4-2 (ESD)
EN61000-4-3 (RS)
EN61000-4-4 (EFT)
EN61000-4-5 (Surge)
EN61000-4-6 (CS)
EN61000-4-8
EN61000-4-11
EMS
Warranty
5 years
Warranty
5 years
LED Color Status Descri pti on
Green On System p ower on
PWR
Green Bli nking Upgrading firmware
R.M Green On Ring Master
On Ring enabled
Ring Green
Blinking Ring structur e is br oken
Fault Amber On Errors (For port malfunctioning)
10/100/ 1000Base-T(X) RJ 45 port
On Port connected at 1Gbps
Green
Blinking Transmitting data
On Port connect ed at 10/100Mbps
Link/Act
Amber Bli nki ng Tran smitting data
PoE Green On PoE-enabl ed
100/1000 Base-X SFP port
On Port connect ed
Link/Act Green
Blinking Transmitting data
RGPS-92222GCP-NP Series
RGPS-92222GCP-NP Series
MANAGED
Rack-Mount
GIGABIT
SWITCH
PoE
Managed Gigabit PoE Ethernet Switch
ORing Industrial Networking Corp.
Copyright© 2014 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]
RGPS-92222GCP-NP-P
Gigabit Combo port with
10/100/1000Base-T(X) P.S.E.
and 100/1000Base-X SFP ports
2
100/1000Base-X with SFP port 2
Power supply 450 Watts power supply included (320W power budget) 1000 Watts power supply included (720W power budget)
-40to60C(-40to140F)
oo
IEC60068-2-27Shock
IEC60068-2-32Free Fall
IEC60068-2-6Vibration
EN60950-1Safety