Orion WB-31 User manual

Installation and User’s Guide
http://www.orionimages.com
All contents of this document may change without prior notice, and actual product appearance may differ
from that depicted herein
Installation and User’s Guide
W
B-31 SWING ARM WALL MOUNT
FLAT LCD DISPLAY MOUNT MODEL

2
Installation and User’s Guide
htt
p
://www.orionima
g
es.com
7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone] pg2
TABLE OF CONTENTS
Parts List …………………………………………………………………………………4
Installation Tools ……………………………………………………………………..….4
Backplate Installation - Wood stud ……………………………………………………...5
Backplate Installation - Concrete Surface ……………………………………………….6
WB-31 Installation ……………………………………………………………………...7
Installing the Monitor …………………………………………………………………....8
Adjusting the Swingout Arm …………………………………………………………….9
Adapter Plate Installation …………………………………………………………….…10
Technical Specifications ………………………………………………………………...11
Warranty Information …………………………………………………………………...12
Contact Orion Images ………………………………………………………………...…12

3
Installation and User’s Guide
htt
p
://www.orionima
g
es.com
7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone] pg3
Warning Statements
WARNING THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A
MAXIMUM WEIGHT OF 50 LBS. IF NOT, THE WALL MUST BE REINFORCED.
PROPER INSTALLATION PROCEDURE BYAQUALIFIED SERVICE TECHNICIAN,
AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED
TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR
EVEN DEATH.
WARNING SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE
INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS
FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.
WARNING PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION
INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE
INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL
INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION
INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE
REFERENCE.
Indicates that the power plug is to be disconnected from the power outlet.
Safety precautions must be taken at all times.
Warning and Caution statements.
A secure structure must support the weight, or load, of the display. When mounting
to a wall that contains wooden studs, dead center of the wooden stud must be
confirmed prior to installation.
Do not install on a structure that is prone to vibration, movement or chance of
impact. Failure to do so could result in damage to the display and/or damage to the
mounting surface.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other
source of direct heat energy. Failure to do so may result in damage to the display
and could increase the risk of fire.
At least two qualified people should perform the installation procedure. Injury and/or
damage can result from dropping or mishandling the display.
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the
mount is to be installed on any surface other than wooden studs, use suitable
hardware (which is commercially available).
Contact Orion Images with any technical/ installation questions.

4
Installation and User’s Guide
htt
p
://www.orionima
g
es.com
7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone] pg4
Part List
NOTE This mount is shipped with all intallation hardware and components. Make sure that
none of these parts are missing and/ or damaged before beginning installation. If
there are parts missing and/or damaged, please stop and contact Orion Images -
714-766-6300
Swing out Arm (Qty 1)
1/4” Wedge Anchors
(Qty 4). These are used
only for concrete
installations.1)
M6 x 35mm Set Screw
(Qty 1)
M4 x 10mm Phillips
Head Screws
(
Qt
y
4
)
#14 x 2” Wood Screw
(Qty 4)
Mounting Back plate
(Qty 1)
200x200 Adapter Plate
(Qty 1)
100x200 Adapter Plate
(Qty 1)
200x200 ADAPTER HARDWARE
M6 x 30mm Phillips Pan
Head Screws (Qty 4)
M6 x 20mm Phillips Pan
Head Screws (Qty 4)
M6 x 12mm Phillips Pan Head
Screws (Qty 4)
M5 x 16mm Phillips Pan Head
Screws (Qty 4)
M5 x 12mm Phillips Pan Head
Screws (Qty 4)
M4 x 20mm Phillips Pan Head
Screws (Qty 4)
M5 Flat
Washer (Qty 4)
M4 Flat
Washer (Qty 4)
M4 x 16mm SEMS
Phillips Pan Head
Screw (Qty 4)
100x200 ADAPTER HARDWARE
M4 x 5mm Phillips Pan Head
Screws (Qty 4)
M4 x 6mm Phillips Pan Head
Screws (Qty 4)
M4 x 10mm Phillips Pan Head
Screws
(
Qt
y
6
)
Installation Tools
Phillips Head Screw Driver, Soft Material/ Blanket, 1/2" Socket and Wrench, Pencil
Tape Measure, Drill Gun, Level (Supplied)
14mm Socket (Supplied), Ratchet with 9/16” Drive Socket
M3 Allen Wrench
(
Su
pp
lied
)
,
Stud Finder
(
Commerciall
y
Available
)

5
Installation and User’s Guide
htt
p
://www.orionima
g
es.com
7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone] pg5
Backplate Installation - Wood Stud
NOTE These installation instructions will apply to the WB-31 Swingout Arm Mount.
The following steps will outline how the back plate will be mounted.
1. Determine where the mount location will be.
2. Use a stud finder (sold separately) to locate the nearest wall stud.
3. Once the wall stud has been located, dead-center of the wall stud must be determined.
4. After this has been determined, line-up the holes of the backplate.
NOTE: Be sure that the end of the back plate that has a “lip” is pointing down (Figure 1).
5. Use the provided wood screws to attach the back plate to the wall (Figure 2).
Figure 1.

6
Installation and User’s Guide
htt
p
://www.orionima
g
es.com
7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone] pg6
Backplate Installation - Concrete Surface
NOTE These installation instructions will apply to the WB-31 Swingout Arm Mount.
The following steps will outline how the back plate will be mounted.
1. Determine where the mount location will be.
2. After this has been determined, line-up the holes of the backplate
3. Once the mounting holes are marked on the wall, use a 5/16” drill bit and drill 4 holes into the
concrete surface (Figure 3).
4. Once the holes have been drilled, gently tap the anchor studs into each hole, until the washer
is flush (even) with the concrete surface.
5. Place the backplate onto the concrete surface and slowly tighten each nut onto its respective
anchor stud (Figure 4).
NOTE: Be sure that the end of the back
p
late that has a li
p
is
p
ointin
g
as shown in
(
Fi
g
ure 3
)
.

7
Installation and User’s Guide
htt
p
://www.orionima
g
es.com
7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone] pg7
W
B-31 Installation
NOTE In reference to Figure 5, the dash lines represent the back plate that is mounted to an
existin
g
surface.
The following steps will outline how the back plate will be mounted.
1. The reverse side of the mount must be mounted to the back plate that is attached to the wall.
The back of the mount contains an elongated rectangle (Figure 5). Referring to Figure 5, the
back plate receptacle must be placed over the top of the back plate, so that the entire mount
“hangs” on the back plate.
2. Locate the access hole at the bottom of the mount base. Install the M6 x 35mm set screw with
the M3 Allen wrench.
3. Turn the Allen wrench clockwise (viewed from below) until the screw is secure.
WARNING: Failure to fully tighten the locking screw may result in possible damage to
y
our dis
p
la
y
.
NOTE: In reference to Figure 5, the dash lines represent the back plate that is
mounted to an existing surface.

8
Installation and User’s Guide
htt
p
://www.orionima
g
es.com
7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone] pg8
Installing the Monito
r
1. Loosely tighten two (2) M4 x 10mm Phillips Head screws to the top of the mounting points.
2. Insert the head of the screws through the keyhole slots and then secure the bottom two (2)
M4 x 10mm Phillips Head screws to secure the flat panel to the mounts, then tighten the
upper M4 x 10mm Phillips Head screws (Figure 6).
CAUTION: Do not over tighten the M4 x 10mm Phillips Head screws, or else damage to
thedis
p
la
y
ma
y
occur.
Cable Access
Please refer to Figure 7 for the correct way to route existing any cables.
WB-31 Articulating Swingout Arm - After the monitor has been mounted, remove the cable
access plastic

9
Installation and User’s Guide
htt
p
://www.orionima
g
es.com
7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone] pg9
Adjusting the Swingout Arm
This unit comes pre-tensioned at the factory. To adjust the swingout Arm so that there will not be
any movement, perform the following steps (Figure 8).
1. Remove the Plastic End Caps.
2. Take a 9/16” socket and ratchet and tighten the nut.
3. Tighten, or loosen, each joint to the user’s satisfaction.
4. Re
p
lace the Plastic End Ca
p
s.
NOTE: The mount shown in this illustration is
upside down to access the adjustment nuts.
NOTE: The tilt/pivot adjustment nut is located
on the back of the tilt/pivot mount.

10
Installation and User’s Guide
htt
p
://www.orionima
g
es.com
7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone] pg10
Adapter Plate Installation
NOTE If your flat panel is not a VESA 75/100, the 200x200 or the 100x200 Adapter Plates
must be used.
100 x 200 Aapter Plate
1. Attach the 100x200 Adapter Plate to the back of the display using the provided hardware
(see Parts List, page 4).
2. Attach the WB-31 mounting plate to the back of the 100x200 using the M4 x 5 mm screws.
200 x 200 Aapter Plate
3. Figure 9B: Attach the 200x200 Adapter Plate to the back of the display using the provided
hardware (see Parts List, page 4).
4. Attach the WB-31 mounting plate to the back of the 200x200, or the 100x200 using the M4
x5mmscrews.
CAUTION: DO NOT OVERTIGHTEN THE SCREWS.
Mounting Hardware (Please refer to Page 4
for the correct mounting hardware that will be
used with your display.
Mounting Hardware (Please refer to Page 4
for the correct mounting hardware that will
be used with your
display