OSD Audio P83 User manual

P83 PATIO SPEAKER INSTALL GUIDE

BLACK P83 INSTALL GUIDE
Preparation:
Installation:
Tools For Installation Speaker Wire Guide
Considerations
Mounting
Placement
Mounting
Wiring
Specications
- Pencil
- Drill
- Tape Measure
- Wire Cutter
- Phillips Screwdriver
- Utility Knife
- Safety Eye Wear
- Gloves
- Where is the best place to install the speakers?
- Where do the speakers sound the best?
- Separate the speakers 6 - 10 feet apart.
If your application requires the speaker to be mounted, please follow these directions. Using the hardware supplied, mount the bracket
rst. Attach the speakers to the brackets using the large plastic knobs supplied. Never mount a speaker on a wall made of unreinforced
drywall or plasterboard. If you are unsure, consult a professional contractor. (See Diagram 1.)
These weather resistant patio speakers are manufactured to resist a variety of weather condition. The most ideal place to install these
speakers is the undersides of most eaves and overhangs as they provide the best protection. Like all speakers, they sound the best
when placed no more than six to ten feet apart from each other, and slightly higher than ear level. If the speakers are more than ten feet
apart, toe them in toward the center of the listening area.
(NOTE) These speakers are not waterproof and cannot be submerged under water.
To install the bracket on the speaker. Screw the bracket knobs
into the cabinet. Point the speaker toward the listening area.
Once the direction of the speaker has been determined tighten
the bracket knobs securely.
(See Diagram 2.)
The binding post speaker terminals on the speakers will accommodate up to 12-guage wire. Connect the speaker cable to the speaker
cable terminals, matching the proper polarity with your amplier, + to + (red) and - to - black). Make sure to connect the right channel
to the right speaker and the left channel to the left speaker. Either channel may be attached to either terminals set, however, be sure
that polarity ( + and - ) is correct on each channel or the performance of the speaker will be seriously affected as one channel will
cancel out the other.
The P83 is equipped to play as a standard 8 Ohm speaker or as a 70V speaker. Choose the correct setting on the back using the dial
to match your application. (See Diagram 3.)
P83
• 8” 2-Way Patio Speaker
• Woofer: 8” Injected PP Cone
• Tweeter: 1” Titanium Dome
• Power Handling: 150W RMS
• Sensitivity: 88dB 1w/1m
• Freq Response: 40Hz - 20kHz
• Impedance: 8 ohms
• 70V Settings: 50W, 25W, 12.5W, 5W, 3W
• Weather Resistant
• Dimensions: HxWxD 13.6” x 8.7” x 9.3”
18AWG minimum - for distances up to …………………. 10 ft
16AWG - from …………………………………..…... 10 to 50 ft
14AWG - from …………………………………...… 50 to 100 ft
BLACK P83 INSTALL GUIDE
Diagram 2
Diagram 3
70V Switch
Diagram 1
8
O
h
m
5
0
W
2
5
W
1
2
.
5
W
5
W
3
W
Binding
Posts

All Optimal Speaker Design outdoor speakers have (2) year Limited Warranty against defects in materials and workmanship. Proof of purchase
must accompany all claims. During the warranty period Optimal Speaker Design will replace any defective part and correct any defect in work-
manship without charge for either parts or labor
Optimal Speaker Design may replace returned speakers with a product of equal value and performance. In such cases, some modications to
the mounting may be necessary and are not Optimal Speaker Design’s responsibility.
For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed
by Optimal Speaker Design. The unit must be returned to Optimal Speaker Design at the owner’s expense and with prior written permission.
Accidental damage and shipping damage are not considered defects, nor is damaged resulting from abuse or from servicing performed by an
agency or person not specically authorized in writing by Optimal Speaker Design
Optimal Speaker Design sells products only through authorized dealers and distributors to ensure that customers obtain proper support and
service. Any Optimal Speaker Design product purchased from an unauthorized dealer or other source, including retailers, mail order dealers and
online sellers will not be honored or serviced under existing Optimal Speaker Design warranty policy. Any sale of product by an unauthorized
source or other manner not authorized by Optimal Speaker Design shall void the warranty on the applicable product.
Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be
made on the basis of the retail value of the parts and labor. To return for repairs, you must email customer service at [email protected]
for a Returned Merchandise Authorization (RMA) number then the unit must be shipped to Optimal Speaker Design at the owner’s expense, along
with a note explaining the nature of service required. Be sure to pack the product(s) in a corrugated container with at least 3 inches of resilient
material to protect the unit from damage in transit.
This Warranty Does Not Cover: Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) • Any products that
have been altered or modied • Any product whose identifying number of decal, serial #, etc. has been altered, defaced or removed • Normal
wear and maintenance.
WARRANTY
Black P83 Manual. rev3 4/18
Optimal Speaker Design | Brea, CA | osdaudio.com