OTC 2010A User manual

Sheet No.
Issue Date: Rev. B November 22, 2010
© 2005 SPX
Form No. 531976
Parts List &
Operating Instructions
for: 2010A
Engine Stand
Maximum Capacity: 454 kg (1000 lbs.)
Weight: 24 kg (52 lbs.)
655 EisEnhowEr DrivE
owatonna, Mn 55060-0995 Usa
PhonE: [phone]
tEch. sErv.: [phone]
Fax: [phone]
orDEr Entry: [phone]
Fax: [phone]
intErnational salEs: [phone]
Fax: [phone]
Original Instructions
1 of 4
Explanation of Safety Signal Words
The safety signal word designates the degree or level of hazard seriousness.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not
avoided, may result in property damage.
Description:
Engine stand designed to support and rotate an
automotive engine during repair and service.
Conforms to
ASME-PALD

Parts List & Operating Instructions Form No. 531976, Sheet 1 of 4, Back
Safety Precautions
CAUTION: To prevent personal injury and/ or property damage,
•Study, understand, and follow all safety precautions and operating instructions before using
this engine stand. If the operator cannot read instructions, operating instructions and safety
precautions must be read and discussed in the operator’s native language.
• Onlyqualiedoperatorsmayinstall,operate,adjust,maintain,clean,repair, inspect, or
transport this engine stand.
•Wear eye protection that meets ANSI Z87.1, CE EN166, AS/NZS 1337, and OSHA
standards.
•Do not exceed the engine stand's rated capacity of 454 kg (1000 lbs.).
•Use this engine stand on a hard, level surface with the wheels and casters level.
•Lock the mounting plate rotating mechanism before applying a load.
•Tapped holes in engine blocks must be clean and not damaged to ensure full thread
engagement. A thread length engagement equal to 11/2screw diameters—minimum—is
required to maintain strength requirements.
• Tomaintainshearstrengthspecications,useMetricPropertyClass8.8orSAEGrade5
capscrewstomountanengine.Mounttheenginesoweightisbalancedwithin51mm(2.0
inches) of the engine stand's rotating axis.
•Ensure the load is centered and secured to mounting attachments. An off-center load may
make the load and handle rotate in either direction when the rotational locking device is
released. Release rotational locking devices SLOWLY and CAREFULLY.
•Stay out from underneath a load that is being lifted or suspended. Never work under an
engine or any other component mounted to this engine stand.
• MovealoadedenginestandSLOWLYtoavoidtipping.
•This engine stand is designed for automotive engines only. Using the engine stand in
a manner for which it was not designed may result in personal injury or damage to the
equipment.
•Do not make alterations to this product.
•Use only those attachments and/or adapters supplied by the manufacturer.
•Inspect the condition of the engine stand before each use; do not use if damaged, altered,
or in poor condition.
•Use only those repair parts called out in the parts list in this document. Items found in the
parts list have been carefully tested and selected by SPX Service Solutions.

Sheet No.
Issue Date: Rev. B November 22, 2010
© 2005 SPX
Parts List & Operating Instructions Form No. 531976
2 of 4
Item
No. Description Qty.
81 Mounting Arm 2
82 Mounting Arm 2
83 Mounting Plate 1
8j4 Bolt 4
8j5 Flat Washer 8
8j6 Nut (M14) 4
8j7 Pin 1
8 Main Post 1
t9 Handle 1
10 Rear Beam 1
j11 Bolt (M12 x 80) 1
12 Center Frame 1
r13 Wheel 2
j14 Bolt (M12 x 25) 2
j15 Washer 4
rj16 Nut (M12) 6
rj17 Bolt (M12 x 65) 2
rj18 Lockwasher 2
r19 Swivel Caster 2
rj20 Bolt (M8 x 50) 2
rj21 Lockwasher 18
rj22 Nut (M8) 8
r j23 Bolt (M8 x 16) 8
j24 Bolt (M12 x 70) 2
r j25 Bushing 2
26 Front Beam 1
Parts List
t Included in Handle Kit No. 532056
j Included in Hardware Kit No. 532059
8 Included in Mounting Arm Kit No. 532058
r Included in Wheel Kit No. 532057
5, 6
7
8
10
9
16, 18
3
14, 15, 16
41
19
17
2
12
11
13
20, 21, 22, 25
22, 21, 23
26
24, 15, 16

Parts List & Operating Instructions Form No. 531976, Sheet 2 of 4, Back
Assembly Instructions
Item numbers refer to the parts list.
1. Attach the center frame (12) to the front beam (26) using bolts, washers, and nuts.
2. Install the main post (8) to the rear beam (10) using bolts, washers, and nuts.
3. Slide the center frame into the main post. Insert the bolt (11) through the hole in the main post, and thread
into the center frame.
4. Install mounting plate (3) into the collar on top of the main post, and secure with a pin (7).
5. Attach four mounting arms (1, 2) to the mounting plate using bolts, washers, and nuts.
6. Slide the handle (9) through the hole at the rear of the mounting plate. Install rubber grips on both ends of
handle.
Operating Instructions
MountingtheEnginetotheEngineStand
1. Determine the engine's center of gravity.
2. Remove the engine clutch bell housing.
3. Remove the mounting plate (with mounting arms loosely attached) from the engine stand. Fasten the four
mounting arms to the engine. Do not tighten the cap screws.
4. Position the mounting plate axis of rotation as close as possible to the engine's center of gravity. Tighten the
cap screws holding the brackets to the engine; tighten the cap screws holding the brackets to the mounting
plate.
5. Attach an engine lifting bar or sling to the engine. Using a suitable lifting device, maneuver the engine
toward the stand.
6. Insert the tubular end of the mounting plate into the stand. Install the pin and handle, and securely fasten
the mounting hardware. Slowly and carefully remove the engine lifting device.
Rotating the Engine
1. Turn the handle (9) on the mounting plate tube to remove the load from the locking pin (7).
2. Pull out the locking pin.
3. Slowly and carefully use the handle to rotate the engine.
4. Once the engine is in position, align the outer tube hole with the inner tube hole, and replace the locking
pin (7).
Removing the Engine from the Engine Stand
1. Attach an engine lifting bar or sling suspended from a suitable lifting device to the engine.
2. Carefully remove the handle and pin from the engine stand, and slowly pull the mounting plate out of the
engine stand.
3. Maneuver the engine away from the engine stand, and unscrew the cap screws holding the mounting
bracket to the engine.

Sheet No.
Issue Date: Rev. B November 22, 2010
© 2005 SPX
3 of 4
Parts List & Operating Instructions Form No. 531976
InspectionandMaintenance
CAUTION: To prevent personal injury,
• Onlyqualiedpersonnelshallperforminspectionsandrepairstothisenginestand.
•Use only those repair parts called out in the parts list in this document. Items found in the parts
list have been carefully tested and selected by SPX Service Solutions.
Inspection
Before each use, an approved inspector must inspect the engine stand for the following conditions:
Cracked or damaged frame members Excessive wear, bending, or other damage
Loose hardware Malfunctioning swivel arms or locking pins
 Modiedoralteredequipment
If any of these conditions are found, discontinue use of the engine stand until corrective action has
been performed.
Maintenance
Periodically clean and lubricate the wheels, casters, and tubular end of the mounting plate. Use a low
temperature grease.
Storage
Store the engine stand in a dry, well-protected area away from corrosive vapors, abrasive dust, or other
harmful elements.
Repair
When repairing the engine stand, use only those repair parts called out in the parts list in this document.
Items found in the parts list have been carefully tested and selected by SPX Service Solutions.
Disposal
At the end of the useful life of the engine stand, dispose of the engine stand according to all state, federal,
and local regulations.
PRODUCTINFORMATION
Recordserialnumberandyearofmanufactureforfuturereference.Seeproductidentication
label on unit for information.
2010A
SerialNumber: YearofManufacture:

EU-Konformitätserklärung
Ich erkläre hiermit, dass das hier benannte Gerät den relevanten
Abschnitten der vorstehend benannten Spezikationen entspricht
und die Anforderungen der Richtlinie(n) erfüllt.
Unterschrift:
Name: Michael Schoenoff
Stellung: Supervisor, Mechanical Engineering
Standort: Owatonna, Minnesota
Datum:
Die technische Dokumentation der Maschine ist erhältlich von
Name: SPX Service Solutions Germany GmbH
Anschrift: Am Dörrenhof 1
85131 Pollenfeld / Preith, Deutschland
vertreten von Gary Palmer, Geschäftsführer
Wir SPX Service Solutions
von 655 Eisenhower Drive
Owatonna, Minnesota 55060-995 USA
erklären hiermit in Übereinstimmung mit der/den folgenden Richtlinie(n):
2006/42/EG Maschinenrichtlinie
dass:
Gerät Motorständer
Modellnummer 2010A
die geltenden Anforderungen der folgenden Dokumente erfüllt:
Ref. Nr. Titel Ausgabe / Datum
entfällt entfällt entfällt
Original-Betriebsanleitung
English
Français
Deutsch
Español
Déclaration de conformité européenne
Je déclare par la présente que l’équipement désigné ici a été
conçu conformément aux sections appropriées des stipulations
susmentionnées et respecte les exigences de la ou des directives.
Signé par :
Nom : Michael Schoenoff
Fonction : Superviseur, génie mécanique
Lieu : Owatonna, Minnesota
Date :
La documentation technique de la machinerie est disponible auprès de
Nom : SPX Service Solutions Germany GmbH
Adresse : Am Dörrenhof 1
85131 Pollenfeld / Preith, Allemagne
représenté par Gary Palmer, Geschäftsführer
Nous, SPX Service Solutions
résidant à 655 Eisenhower Drive
Owatonna, Minnesota 55060-995, États-Unis
selon la ou les directives suivantes :
2006/42/CE Directive relative aux machines
déclarons par la présente que :
Équipement Support de moteur
Numéro de modèle 2010A
est conforme aux exigences applicables des documents suivants :
Nº de référence Titre Édition/Date
S/O S/O S/O
Consignes d’origine
Declaración de conformidad con EC
Declaro por la presente que el equipamiento nombrado aquí ha sido diseñado
para cumplir con las secciones relevantes de las especicaciones anteriormente
indicadas y está de acuerdo con los requisitos de la(s) Directiva(s).
Firmado por:
Nombre: Michael Schoenoff
Puesto: Supervisor, Ingeniero mecánico
Ubicación: Owatonna, Minnesota
Fecha:
La documentación técnica para la maquinaria está disponible en
Nombre: SPX Service Solutions Germany GmbH
Dirección: Am Dörrenhof 1
85131 Pollenfeld / Preith, Alemania
representado por Gary Palmer, Geschäftsführer
Nosotros SPX Service Solutions
de 655 Eisenhower Drive
Owatonna, Minnesota 55060-995 USA
de acuerdo con la(s) siguiente(s) Directiva(s):
2006/42/EC La directiva de la maquinaria
por la presente declaro que:
Equipo Soporte de motor
Número de modelo 2010A
está en conformidad con los requerimientos aplicables de los siguientes
documentos:
No. de Ref. Título Edición / Fecha
N/A N/A N/A
Instrucciones originales
EC Declaration of Conformity
I hereby declare that the equipment named here has been designed to
comply with the relevant sections of the above referenced specications
and is in accordance with the requirements of the Directive(s).
Signed by:
Name: Michael Schoenoff
Position: Supervisor, Mechanical Engineering
Location: Owatonna, Minnesota
Date:
The technical documentation for the machinery is available from
Name: SPX Service Solutions Germany GmbH
Address: Am Dörrenhof 1
85131 Pollenfeld / Preith, Germany
represented by Gary Palmer, Geschäftsführer
We SPX Service Solutions
of 655 Eisenhower Drive
Owatonna, Minnesota 55060-995 USA
in accordance with the following Directive(s):
2006/42/EC The Machinery Directive
hereby declare that:
Equipment Engine stand
Model Number 2010A
is in conformity with the applicable requirements of the following
documents:
Ref. No. Title Edition / Date
N/A N/A N/A
Original Instructions

Italiano Dichiarazione di conformità CE
Si dichiara che la macchina descritta in questo documento è stata
progettata in conformità alle pertinenti sezioni delle speciche a cui si
fa riferimento sopra e risponde ai requisiti delle direttive.
Firma:
Nome: Michael Schoenoff
Qualica: Direttore ingegnerizzazione meccanica
Sede: Owatonna, Minnesota
Data:
Il fascicolo tecnico della macchina è disponibile presso:
Nome: SPX Service Solutions Germany GmbH
Indirizzo: Am Dörrenhof 1
85131 Pollenfeld / Preith, Germania
Mandatario: Gary Palmer, Geschäftsführer
L'azienda SPX Service Solutions
con sede a 655 Eisenhower Drive
Owatonna, Minnesota 55060-995 USA
in conformità alle seguenti direttive:
2006/42/CE Direttiva Macchine
dichiara che:
La macchina Cavalletto per motori
Modello 2010A
risponde ai pertinenti requisiti dei seguenti documenti:
N. rif. Titolo Edizione / Data
Non pert. Non pert. Non pert.
Istruzioni originali