Outdoor Gourmet 166766 Owner's manual

MODEL NUMBER 166766 Page 1 of 25 11/27/21-Ver.1
Assembly Instructions
& User’s Manual
OUTDOOR GOURMET 6 BURNER 44IN GRIDDLE
MODEL NUMBER 166766
Please keep this instruction manual for future reference
Customer Service: 1-888-922-2336
7:00 am to 12:00 am CST (daily)
Live Chat at: www.academy.com
Email: [e-mail]
(Made in China)
For Outdoor Use Only

MODEL NUMBER 166766 Page 2 of 25 11/27/21-Ver.1
Note: Triton-Tek non-scratch griddle surfaces require non
abrasive utensils to avoid scratching and removing the coating.
Lookfor your Triton-Tek compatible equipment at Academy
stores and on-line.
Note: Before beginning assembly of product, make sure all
parts are present. Compare parts with package content list and
hardware contents. If any part is missing or damaged do not
attempt to assemble the unit. Contact customer service for
replacement parts.
Table of Contents
Warnings --------------------------------------------------------------------------------------------------
P. 3 – 7
Product Diagram ----------------------------------------------------------------------------------------
P. 8
Parts List --------------------------------------------------------------------------------------------------
P. 9 – 10
Hardware List --------------------------------------------------------------------------------------------
P. 11
Tools Required ------------------------------------------------------------------------------------------
P. 11
Assembly Procedures ---------------------------------------------------------------------------------
P. 12 – 20
Trouble Shooting ----------------------------------------------------------------------------------------
P. 21
Care & Maintenance -----------------------------------------------------------------------------------
P. 22
Operating Instructions----------------------------------------------------------------------------------
P. 23
Sample Recipe---------------------------------------------------------------------------------
P. 24
Warranty Information -----------------------------------------------------------------------------------
P. 25

MODEL NUMBER 166766 Page 3 of 25 11/27/21-Ver.1
WARNINGS
To installer or person assembling this appliance: Leave this manual with this appliance for future reference.
This instruction manual contains important information necessary for the proper assembly and safe use of the appliance.
Read and follow all warnings and instructions before assembling and using the appliance.
Follow all warnings and instructions when using the appliance.
Keep this manual for further reference.
Check for leaks according to directions in this manual before operating, even if this appliance was purchased fully assembled.
WARNINGS
SAFETY SYMBOLS:
The symbols and boxes shown below explain what each heading means. Read and follow all of the messages found throughout the
manual.
DANGER: Indicates an imminent hazardous situation which if not avoided will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
DANGER
If you see, smell, or hear escaping gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department.
Failure to follow these instructions could result in fire or explosion which could cause property damage, personal injury or death.
DANGER
1. Appliance installation must conform with local codes, or in their absence, with the National Fuel Gas Code ANSI Z223.1/NFPA 54,
Storage and handling of liquefied petroleum gases, ANSI/NFPA 58; or the Natural Gas and Propane Installation Code, CSA B1 49.1:
Natural Gas and Propane Installation Code CSA B149.1 or Propane Storage and Handling Code B149.2.
2. Appliance, when installed, must be electrically grounded in accordance with either the National Fuel Gas Code, or, in absence of
local codes, with the National Electrical Code ANSI Z21.58-2018, or the Canadian Electrical Code, CSA 1.6-2018
3. This product is designed and tested to operate on LP gas (propane). Any conversions to other fuel sources such as Natural Gas is not
recommended, and any such conversions will automatically void all warranty and liabilities.
4. The pressure regulator and hose assembly supplied with this appliance must be used. Replacement pressure regulator and hose
assemblies must be those specified by the appliance manufacturer.
Failure to follow these instructions could result in fire, explosion or burn hazard which could cause property damage, personal injury, or
death.

MODEL NUMBER 166766 Page 4 of 25 11/27/21-Ver.1
DANGER
1. This appliance is for OUTDOOR USE ONLY. Do not use inside any building, garage, or other enclosed area.
2. Never operate this appliance unattended. Always keep children and pets away from the appliance.
3. Never operate this appliance within 3 ft (1.0 m) of any structure, combustible material, or other gas cylinder. Maintain 3 ft
clearance to objects that can catch fire or any source of ignition, such as pilot lights on water heaters, live electrical
appliances, etc.
4. Never operate this appliance within 25 ft (7.5 m) of any flammable liquid. Do not store flammable liquids or vapors in the vicinity
of this or any other appliance.
5. This appliance is not intended to be installed in or on recreational vehicles and/or boats; Never attempt to attach this
appliance to the self-contained LP gas system of a camper, trailer, or motorhome.
6. Only use the pressure regulator with a type 1 connector that is supplied with this appliance.
7. Before each use, check the gas hose for excessive abrasion, cracking, fraying, wear, or cuts. Replace a hose assembly showing
any of these signs with the hose assembly specified in the parts list before using the appliance.
8. Never allow oil or grease to get hotter than 400°F or 204°C. If the temperature exceeds 400°F (204°C) or if oil begins to smoke,
immediately turn the burner, or gas supply OFF.
9. Heated liquids remain at scalding temperatures long after the cooking process. Never touch cooking appliance until liquids
have cooled to 115°F (45°C) or less.
10.If you notice grease or other hot material dripping from appliance onto LP valve, hose, or regulator, turn off gas supply at once.
Determine the cause, correct, clean, and inspect valve, hose, and regulator before continuing. Perform a leak test.
11.If a fire should occur, keep away from the appliance and immediately call your fire department. Do not attempt to extinguish
an oil or grease fire with water.
12.Clean and inspect the hose before each use of the appliance. If there is evidence of abrasion, wear, cuts or leaks, the hose
must be replaced prior to the appliance being put into operation. Always perform a leak test before operating this appliance.
Failure to follow these instructions could result in fire, explosion or burn hazard which could cause property damage,
personal injury, or death.
WARNING
This Appliance is not intended for commercial use.
WARNING
1. The safety relief valve on the LP tank could activate releasing gas and cause an intense fire with risk of death or serious injury.
Therefore, follow instructions below exactly.
2. Do not insert any tool or foreign object into the valve outlet or safety relief valve. You may damage the valve and cause a leak.
Leaking propane may result in explosion, fire, sever personal injury or death.
3. Do not use the appliance until a leak check is performed.
4. If a leak is detected at any time STOP.
5. If you cannot stop a gas leak, immediately close LP tank valve, leave area of appliance, and call LP gas supplier or your fire
department.

MODEL NUMBER 166766 Page 5 of 25 11/27/21-Ver.1
WARNING
General Safety Precautions.
1. The use of alcohol, prescription or non-prescription drugs may impair the consumer’s ability to properly assemble or safely operate
the appliance.
2. This appliance is not intended for and should never be used as a heater.
3. When cooking, the appliance must be on a level, stable noncombustible surface in an area clear of combustible material. Asphalt
surface (blacktop) may not be acceptable for this purpose.
4. Keep the fuel supply hose away from any heated surface. Use caution as fuel supply hose may be a trip hazard.
5. When cooking with oil or grease, have a type BC or ABC fire extinguisher readily available. In the event of an oil or grease fire do
not attempt to extinguish with water. Immediately call the fire department. Type BC or ABC fire extinguisher may, in some
circumstances contain the fire.
6. Introduction of water or ice from any source into hot oil/grease may cause overflow and severe burns from hot oil and water
splatter. When cooking with oil/grease, all food products MUST be completely thawed, and towel dried.
7. Do not place empty pots (cooking vessels) on the appliance while in operation. Use caution when placing anything in heated pots
(cooking vessels) while the appliance is in operation.
8. In the event of rain, snow, hail, sleet, or other forms of precipitation while cooking with oil or grease, cover immediately and turn off
appliance burner and gas supply. Do not attempt to move the appliance or any cooking vessels.
9. This appliance will be hot during and after use. Use insulated protective gear for protection from hot surfaces or splatter from
cooking liquids and hot surfaces.
10.Avoid bumping of or impact with the appliance to prevent spillage or splashing of hot substances.
11.Never drop food or accessories into hot cooking liquid or hot surfaces. Lower food and accessories slowly to prevent splashing or
overflow. When removing food from the appliance care should be taken to avoid burns from hot cooking liquids and surfaces.
12.Do not store appliances or tools on hot surfaces to avoid damage and wear.
13.Do not move the appliance when in use. Allow the cooking vessel to cool to 115°F (46°C) before moving or storing.
14.The minimum outside temperature tolerance of this appliance is 32°F (0°C). Never use this appliance when temperature is below
this minimum.
15.Never operate appliance with LP tanks out of correct position specified in assembly instructions.
WARNING
Connecting Regulator to the LP Tank
1. Place LP tank on a secure, level, and stable surface.
2. Turn the regulator control knob to the OFF position.
3. Turn LP tank OFF by turning OPD hand wheel clockwise to a full stop.
4. Remove the protective cap from the LP tank valve. Always use dust cap and strap supplied with valve.
5. Hold regulator, insert nipple (B) into LP tank valve. Hand tighten coupling nut, holding regulator in a straight line (C) with LP tank
valve so as not to cross thread the connection.
6. Before opening LP tank valve, check the coupling nut for tightness. When appliance is not in use, ensure both control knob and LP
tank valve are turned OFF.
7. Turn the coupling nut clockwise to tighten to a full solid stop. The
regulator will seal on the back-check feature in the LP tank valve,
resulting in some resistance. An additional one-half to three quarters
turn is required to complete connection. Tighten by hand only – do
not use tools.
8. The regulator may make a humming or whistling noise during
operation. This will not affect safety or use of appliance.
NOTE: If you cannot complete connection, disconnect regulator, and
repeat step 5 and 6. If you are still unable to complete the connection, do
not use this regulator!

MODEL NUMBER 166766 Page 6 of 25 11/27/21-Ver.1
DANGER
LP Tank Removal, Transport and Storage
1. Turn OFF all control knobs and LP tank valve. Turn coupling nut counterclockwise by hand
only – do not use tools to disconnect. Place dust cap on cylinder valve outlet whenever
the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that
is provided with the cylinder valve. Other types of caps or plugs may result in leakage of
propane.
2. A disconnected LP tank in storage or being transported must have a safety cap installed
(as shown). Do not store an LP tank in enclosed spaces such as a carport, garage, porch,
covered patio or other building. Never leave an LP tank inside a vehicle which may
become overheated by the sun.
3. Do not store LP tanks in an area where children play.
LP Tank
The LP tank used with your appliance must meet the following requirements:
1. Purchase LP tanks only with these required measurements: 12” (30.5cm) (diameter) x 18” (45.7cm) (tall) with 20lb. (9kg). Capacity
maximum.
2. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the specifications for LP-gas cylinders
of the US Department of Transportation (DOT) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes
for the Transportation of Dangerous Goods.
LP tank valve must have:
1. Type 1 outlet compatible with regulator or appliance.
2. Safety relief valve.
3. UL listed Overfill Protection Device (OPD). This OPD safety feature is identified by a unique triangular
hand wheel. Use only tanks equipped with this type of valve.
4. LP tank must be arranged for vapor withdrawal and include collar to protect LP tank valve.
LP (Liquefied Petroleum Gas)
1. LP gas is non toxic, odorless and colorless when produced. For your safety, LP gas has been given an
odor (similar to rotten cabbage) so that it can be smelled.
2. LP gas is highly flammable and may ignite unexpectedly when mixed with air.
LP Tank Filling
1. Use only licensed and experienced dealers.
2. LP dealer must purge tanks before filling.
3. Dealer should NEVER fill LP tank more than 80% of LP tank volume. Volume of propane in tanks will vary by temperature.
4. A frosty regulator indicates gas overfill. Immediately close LP tank valve and call LP gas dealer for assistance.
5. Do not release liquid propane (LP) gas into the atmosphere. This is a hazardous practice.
6. To remove gas from LP tank, contact an LP dealer or call a local fire department for assistance. Check the telephone directory
under” GAS Companies” for nearest certified LP dealers.
LP Tank Exchange
1. Many retailers that sell appliances offer you the option of replacing your empty LP tanks through an exchange service, Use only
those reputable exchange companies that inspect, precision fill, test and certify their cylinders. Exchange your tank only for an
OPD safety feature-equipped tanks as described in the “LP Tank” section of this manual.
2. Always keep new and exchanged LP tanks in upright position during use, transit or storage.
3. Leak test new and exchanged LP tanks BEFORE connecting to appliance.
LP Tank Leak Test
For your safety
1. Leak test must be repeated each time LP tank is exchanged or refilled.
2. Do not smoke during leak test.
3. Do not use an open flame to check for gas leaks.
LP tank must be leak checked outdoors in well-ventilated area, away from open flames or sparks.
1. Use a clean paint brush and 50/50 soap and water solution.
2. Use mild soap and water. Do no use household cleaning agents or damage to gas line components
may occur.
3. Brush soapy solution onto all weld seams and entire valve area.
4. If “growing” bubbles appear, do not use or move the LP tank, contact an LP gas supplier or your fire
department.

MODEL NUMBER 166766 Page 7 of 25 11/27/21-Ver.1
CAUTION
If burner does not light OR if burner flame is accidentally extinguished, turn the regulator control knob to OFF, wait 5 minutes, and try
again. If the burner does not ignite with valve open OR if burner flame is accidentally extinguished after lighting, gas will continue to flow
out of the burner and could accidentally ignite with risk of injury.
Turning the appliance on
1. Turn LP tank ON by turning OPD handle wheel counterclockwise to a full stop, turn the regulator
control valve to ON position, turn the burner clockwise, self-ignition should occur at first ¼ turn, you
should hear the igniter activate. Check for flame at burner.
Burner Flame Check
2. Light burner, rotate the regulator control knob from HIGH to LOW. You should see a smaller flame in
LOW position than seen on HIGH. Always check flame prior to each use. A blue flame with little or no
yellow flame provides the best heat.
Turning the appliance off
3. Turn the burner counterclockwise to OFF position, turn the regulator control valve to OFF position, turn
LP tank OFF by turning OPD hand wheel clockwise to a full stop.
CAUTION
Regularly check and clean the burner venturi tube for insect nests. A clogged burner can lead to fire beneath the appliances. Spiders’
nests or wasps’ mud inside the burner may cause fire. If a fire occurs, immediately turn off gas supply at LP tank valve. Refer to the Care &
Maintenance section for details on cleaning and maintaining the burners.
WARNING
Leak Testing Valves, Hoses and Regulator
1. Turn LP tank valve and regulator control knob to OFF.
2. Be sure regulator is tightly connected to LP tanks.
3. Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a
rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before
proceeding.
4. Brush soapy solution onto indicated connections shown below in A.
5. If ‘growing” bubbles appear, there is a leak. Close LP tank valve immediately and retighten
connections. If leaks cannot be stopped, do not try to repair. Call for replacement parts. Order
new parts by giving the serial number, model number and name of items needed to the
Customer Service Center at 1-888-922-2336. Use only replacement parts specified by
manufacturer.
6. Always close LP tank valve after performing tank leak test by turning OPD hand wheel clockwise.
CAUTION
All cleaning and maintenance should only be done when the appliance is cool and with the fuel supply turned off at the LP tank. DO
NOT clean any part in a self-cleaning oven. The extreme heat will damage the finish. Refer to the Care & Maintenance section for details
on cleaning and maintaining the appliance.

MODEL NUMBER 166766 Page 8 of 25 11/27/21-Ver.1
PRODUCT DIAGRAM
Expanded view showing all component locations and hardware placements for reference.

MODEL NUMBER166766 Page 9 of 25 11/27/21-Ver.1
PARTS LIST
Ensure all parts listed are present prior to assembly. If any parts are missing or damaged, please contact customer service immediately.
Frame Base
Frame Side (L)
Frame Side (R)
Door Magnet
Cabinet Rear
Caster
Lower Tank Bracket
Upper Tank Bracket
Cabinet Support
Fence Rail
Cabinet Door Handle
Door Handle Insert
Cabinet Door (L)
Cabinet Door (R)
Bottle Opener
Tank Protector
Fire Box
Protector Bracket
Side Shelf Bracket
Side Shelf Stay
Side Shelf Stay
Bottle Holder
Side Shelf Bracket
Side Shelf (L)
Tool Hook
Side Shelf (R)
Towel Rack
Serving Shelf Support
Warming Rack
Griddle
Paper Towel Holder
Hose Clamp( In Blister Box)

MODEL NUMBER 166766 Page 10 of 25 11/27/21-Ver.1
Serving Shelf Support
Serving Shelf
Lid
Lid Handle
Grease Tray Face
Grease Tray Handle
Grease Tray

MODEL NUMBER166766 Page 11 of 25 11/27/21-Ver.1
HARDWARE LIST
Ensure all hardware listed is present prior to assembly. If any hardware is missing or damaged, please contact customer service
immediately.
TOOLS REQUIRED
Collect and have ready these required tools prior to beginning assembly.
Adjustable Wrench
Phillips Screwdriver
Two Persons
(GG) Hose Clamp

MODEL NUMBER 166766 Page 12 of 25 11/27/21-Ver.1
ASSEMBLY PROCEDURES
Please review all steps prior to beginning. Follow steps in order and ensure all parts and hardware are assembled correctly for proper fit
and finish. Some parts may have similarities on multiple sides, ensure proper placement and facing of each component to ensure proper
assembly.
Connect Frame Base (1) to Frame Sides (2
& 3) as shown, finger tighten.
Connect Door Magnet (4) to Frame Base
Assembly as shown.
Screw casters to frame sides as shown,
completely tighten.
Attach Cabinet Back (5) to Frame
Assembly as shown. Finger tighten.

MODEL NUMBER 166766 Page 13 of 25 11/27/21-Ver.1
Attach Upper Tank Bracket and Lower
Tank Bracket as shown in image. Tighten
Completely.
Add Cabinet Supports (9) to Frame
Assembly as shown. Finger tighten.
Add Fence Rail (10) to Frame Assembly as
shown. Finger Tighten.
Attach Cabinet Door Handles (11) to
Cabinet Door (13) and Door Handle Inserts
(12) as shown. Tighten Completely.

MODEL NUMBER 166766 Page 14 of 25 11/27/21-Ver.1
Attach Cabinet Door Handles (11) to
Cabinet Door (14) and Door Handle Inserts
(12) as shown. Tighten Completely.
Attach Cabinet Door Assemblies to Frame
Assembly as shown, follow the steps listed.
Attach the Bottle Opener (15) to the
Frame Assembly as shown.
Add the Paper Towel Holder (16) to the
inner bracket on the Frame Assembly as
shown.

MODEL NUMBER 166766 Page 15 of 25 11/27/21-Ver.1
Add the Tank Protector (17) to the Frame
Assembly as shown.
Add the Fire Box (18) to the Frame Assembly
as shown. Finger tighten.
(Two persons required)
Add the Protector Bracket (19) to the Frame
Assembly as shown. Tighten completely.
Tighten all bolts on Frame Assembly at this
time.
Add Side Shelf Brackets (20 & 21) to Frame
Assembly as shown, tighten completely.

MODEL NUMBER 166766 Page 16 of 25 11/27/21-Ver.1
Add Shelf Supports (23&24) and Bottle Holder
(22) to Side Shelf (Right) (25) as shown, tighten
completely.
Unscrew wing nuts from Tool Hooks (26) and
align to Side Shelf as shown. Replace wing
nuts and tighten completely.
Add Shelf Supports (23 & 24) to Side Shelf
(Left) (27) as shown, tighten completely.
Remove bolts and washers from Towel Rack
(21) and align to Left Side Shelf Assembly,
Bolt in place as shown, tighten completely.
CC

MODEL NUMBER 166766 Page 17 of 25 11/27/21-Ver.1
Place left side shelf assembly to frame
assembly and connect Shelf Brackets and
Shelf Supports as shown. Tighten completely.
Place right side shelf assembly to frame
assembly and connect Shelf Brackets and
Shelf Supports as shown. Tighten completely.
Add studs to griddle (29) underside as shown.
Add nuts to studs as shown. (This allows for
griddle adjustment and leveling)
Place Griddle (29) on Frame Assembly
placing studs in predrilled holes in Fire Box.
(Two persons required)

MODEL NUMBER166766 Page 18 of 25 11/27/21-Ver.1
(Optional) Unfold Warming Rack (30) legs
and place on rear of griddle as shown.
Place Hose Clamp on LP Regulator and
Hose assembly and bolt to Frame Assembly
as shown. Tighten completely.
Bolt Serving Shelf Supports (32&33) to Serving
Shelf (34) as shown. Tighten completely.
Lid hanging on back of firebox
while preheating and cooking
Lid covering appliance for storage
or GG
Be sure to secure the hose by
hose clamp to prevent it
touching the bottom of firebox

MODEL NUMBER 166766 Page 19 of 25 11/27/21-Ver.1
Bolt Lid Handles (36) to Lid (35) as shown.
Tighten completely.
Bolt grease tray handle (39) through Grease
Tray Face (38) to Grease Tray (37) and tighten
bolts completely. Place in firebox accordingly.

MODEL NUMBER 166766 Page 20 of 25 11/27/21-Ver.1