OVARRO TBOX MS-GSM-4W User manual

TBOX MS-GSM-4W
Version 3.04

Ovarro S.A Registered Office: Drève Richelle 161, Waterloo Office Park Building M, Box 35b, 1410 Waterloo, Belgium / Belgique
Company Number: Belgium No. RLE (Nivelles) 0886.847.541
Technical specifications may change before prior notice Version. 3.04
TBOX MS-GSM-4W
Available for MS-CPU32 and MS-CPU32-S2,
not available for MS-CPU16
Worldwide LTE modem, except:
oChinese Operators using TDD technologies and Verizon in US
Twelve Band LTE (4G)
Seven Band UMTS/HSPDA (3G)
Quad Band GSM/GPRS/EDGE (2G)
GSM IP mode communication (through APN)
Send/Receive SMS
1 port RS232/RS485 non isolated
Technical Specifications
General
Construction
Industrial grade LTE (4G) modem
Consumption
On the BUS : 30 mA
On Vp : Max. 4.75 W
Replacement
Hot insertable/removable. There is no risk to damage hardware, but a reset is required
Test
Automatic test of the access of the card by the CPU
(See LED ‘CS’ below)
4G Modem
Frequencies
LTE (4G): Twelve band, 700 (Bd12 <MFBI Bd17>, Bd28) / 800 (Bd18, Bd19,
Bd20) / 850 (Bd5) / 900 (Bd8) / AWS (Bd4) / 1800 (Bd3) / 1900 (Bd2) / 2100
(Bd1) / 2600 (Bd7)
UMTS/HSPA+ (3G): Seven band, 800 (BdXIX) / 850 (BdV) / 900 (BdVIII) / AWS
(BdIV) / 1800 (BdIX) / 1900 (BdII) / 2100MHz (BdI)
GSM/GPRS/EDGE (2G): Quad band, 850/900/1800/1900 MHz.
Output Power
According to Release 8 (4G):
Class 3 (+23dBm ±2dB) for all bands
According to Release 99 (3G):
Class 3 (+24dBm +1/-3dB) for all bands
According to Release 99 (2G):
Class 4 (+33dBm ±2dB) for EGSM850
Class 4 (+33dBm ±2dB) for EGSM900
Class 1 (+30dBm ±2dB) for GSM1800
Class 1 (+30dBm ±2dB) for GSM1900
Class E2 (+27dBm ± 3dB) for GSM 850 8-PSK
Class E2 (+26dBm ± 3dB) for GSM 900 8-PSK
Class E2 (+26dBm +3 /-4dB) for GSM 1800 8-PSK
Class E2 (+26dBm +3 /-4dB) for GSM 1900 8-PSK

Ovarro S.A Registered Office: Drève Richelle 161, Waterloo Office Park Building M, Box 35b, 1410 Waterloo, Belgium / Belgique
Company Number: Belgium No. RLE (Nivelles) 0886.847.541
Technical specifications may change before prior notice Version. 3.04
LEDs (GSM)
Network
On Line
T/R
Flashes when the GSM is connected to the network
Indicates that the GSM is connected to an APN
Flash ON when GSM is transmitting
SIM card
3V and 1.8V SIM cards
Standard size SIM card.
Antenna connector
Screw connector, type SMA female (Jack) on MS-GSM card
RS232 –RS485
Mode
RS232 or RS485 (no simultaneous use of both modes)
Isolation
No isolation. Gnd is linked to earth by internal connection
RS232
Signals: RxD, TxD, CTS, RTS, DTR, DSR, DCD, RI
Connector: 9 pin Sub-D (male)
RS485
Cabling: 2 wires (A+ and B-) for multi-points connection
Termination: no need for termination resistor (failsafe bias resistors included: pullup
and pulldown resistors which assures a logical level TRUE when A and B are opened or
in short circuit)
Number of slaves: 256 (if RS485 technology of slaves allows it too)
Connector: screw connector (3 x 5.08 mm)
LEDs (common to 2 ports)
RxD
TxD
Indicates reception of data
Indicates transmission of data
LED
Cs
Card Selection: card corresponding to card declared in TWinSoft.
ER
Error: card type not corresponding to the one declared in TWinSoft.
Environment
Temperature storage
-40°C to 85°C
Temperature working (ambient)
Industrial Temperature: -40°C to 70°C
Humidity
15 to 95 % without condensation
Altitude
Max. 5000 m
Dimensions
Without connector
Height x Depth x Width: 150 x 83 x 29 mm
Weight
300 g
Approvals
CE, UL, CSA, FCC, C-Tick

Ovarro S.A Registered Office: Drève Richelle 161, Waterloo Office Park Building M, Box 35b, 1410 Waterloo, Belgium / Belgique
Company Number: Belgium No. RLE (Nivelles) 0886.847.541
Technical specifications may change before prior notice Version. 3.04
Antennas
One model of antenna covers all frequencies (700/806/850/1800/1900/2100/2500/2600 Mhz).
Reference. ACC-GSM-ANT-4G
Antenna Surge Arrestor
Connection to the arrestor:
1. Use the N-M>>N-M connector from the arrestor to connect it to the antenna (remove N-
M>>FME-M from antenna if mounted).
2. Connect N-M>>FME-M adapter supplied with the antenna to the arrestor.
3. Connect the corresponding wire.
1
2
3