Owlet Owlet Cam User manual

1
Owlet Cam Installation Guide
Owlet Cam Guide d’installation
Owlet Cam Installationsanleitung
Owlet Cam Installationsguide
Owlet Cam Installasjonsveiledning
Owlet Cam Installationsvejledning
Owlet Cam Installatiegids
Owlet Cam Uppsetningarleiðbeiningar
Owlet Cam Asennusopas
Owlet Cam Guida per l’installazione
Owlet Cam Guía de Instalación
EN |FR |DE |SV |NO |DA |NL |IS |FI |IT |ES

2
Let’s Get Started
Download the Owlet App.
Plug in and follow app instructions
to pair the Cam with your Owlet
Account.
If you’ve already downloaded the
Owlet App, click the Account tab to
add a new device.
EN
Guide to Owlet Cam Status Lights
(blinking red/blue) Cam is ready to pair with App
(red) User is actively streaming via App
(blinking blue) Cam is trying to connect to Wi-Fi
(blue) Cam is connected to internet. App is not streaming
Remember: the Cam allows for video
and audio via secure, encrypted
Wi-Fi. Only connect the Cam to a
private network that requires
a secure password.

3
Choose Your View
Place the Cam and all cables 3 feet
away from the edge of the crib. Cables
within 3 feet of the edge of the crib
should be covered.
You can set up the Cam in two ways:
1 Place it on a flat surface using the
magnetic base and adjust for
desired tilt angle.
2Mount it on a wall above the crib
using the base as a wall mount for
a bird’s-eye view of the crib or for
an expanded view of your nursery.
The next steps will guide you through
mounting the Cam on the wall (above
the crib).
You can also view our Installation Video
at support.owletcare.com

4
What’s in the Box
Owlet Cam
Mounting
plate
Magnetic base
Measuring tape
(not included)
Cables with Owlet wraps*
and room temperature sensor
21x cable guards
18x long guards
1x end piece
2x L-brackets
Power adapters
Small Phillips screwdriver
(not included)
1x screw
Wall Mounting Kit Tools Needed to Mount the Cam
*Previous versions may include a cable box
for cable managemenent

5
1. Measure and mark
Consider which outlet to use.The
outlet should be at least 36 inches
away from the crib to ensure no
exposed cables will be within baby’s
reach. The next steps will instructyou
on how to cover all cables.
Measure 36 inches from the top of
your baby’s mattress and make a
mark on the wall — this is where the
Cam will be mounted. Center this
mark above baby’s crib for the optimal
viewing angle.
36 inches
36 inches
(six cable guards)
It’s also important to consider the
location of the temperature sensor.
The temperature sensor can be found
near the end of the smart cable on
the side that connects to the power
adapter.

6
3. Unwind the cable 4. Thread the cable
Remove the cable wraps and
unwind the cable.
Thread the cable down the channel
of the mounting plate, aligning the
orange sticker on the cable to the top
of the mounting plate.
2. Align and fasten
Align the center hole of the mounting
plate with the mark you’ve made on
the wall. Using the provided screw,
fasten the mounting plate to the wall
with the arrows pointing upward.
sticker

7
5. Mount the base
Position the large holesof the
magnetic base over the protruding
tabs onthe mounting plate, then slide
downward until it clicks.
sticker
Attach the Cam to the magnetic base.
Plug the cable into the Cam.
6. Attach the Cam
The orange sticker should be
placed just above the mounting plate
so that you have enough cable
slack to position the Cam to your
desired angle.

8
The cable guards use high-strength
adhesive. Take your time during
installation to ensure proper placement.
1Peel off adhesive cover from the
back of a long guard
2Thread cable down the center
of a long guard
3Snap long guard onto the
bottom of the mounting plate
4Press firmly onto wall
5Repeat steps 1–4 with remaining
long guards until you reach the
height of the wall outlet
7. Mount cable guards
long guard

9
Use the right or left L-bracket to guide
the cable in the direction of the wall
outlet.
Install long guards until any cable
within 36 inches of the edge of the
crib is covered. Continue adding long
guards as needed to reach the outlet.
Finally, install the end piece when you
are within 6-10 inches of the outlet
(this allows enough room to wrap
excess cable with velcro).
8. Mount L-bracket
L-brackets
end piece

10
For contact information specific to
your region, please visit
http://support.owletcare.com
Need Help?
Gather the excess cable into a loop.
Secure the top section of the loop
by feeding the cable wrap through
the first hole. The Owlet logo faces
outward. Secure the bottom section
of the loop to the top section by
feeding the cable wrap through the
second hole (The loop should now
look like a bow). Secure remaining
cable wrap.
Once the excess cable has been
wrapped securely, connect the power
cable to the power adapter and plug
it in.
You’re all set! You can now use the
App to reference how to adjust the
Cam angle until you achieve the
desired view.
9. Wrap excess cable with velcro