Ownboard W-series User manual

E-SKATEBOARD
USER MANUAL
The manual applies to W-series, C-series and
MINI-series of OWNBOARD e-skateboard

www.ownboard.net
Contents
2 Introduction
3 Included in the Box
4 Features and Specs
5 Charging the Battery
7 Operating the E-Skateboard
10 Safety Warnings
9 Care and Maintenance
8 Safe Ridiing
11 Warranty
02
03
04
05
06
07
08-09
10
11-12
13-14
15
2
6 Power Indicators
1 Contents

www.ownboard.net
Introduction
Congratulations on your new OWNBOARD E-Skateboard! The E-Skateboard is an innovative and
fun electric Skateboard, ready to take on everyday use. Before your first ride, check whether the
wheels are damaged, or parts are loose. If there are any abnormalities, please contact OWNBOARD
Customer Support or email us at [email protected].
This product manual can help you understand, use, and maintain your E-Skateboard. In order to
avoid danger caused by collisions, falls, and loss of control, please use caution and learn how to
ride the E-Skateboard safely. OWNBOARD and authorized dealers cannot be held liable for injury
or damage caused from riding the E-Skateboard. Users ride at their own risk.
The rider is responsible for consequences caused by violating warnings or improper operations.
If you have any question for this product ,be sure to first call or email us so we can assist you.
3

www.ownboard.net
Included in the Box
4
E-Skateboard Remote Control Tools USB Cable Charger
1
2
6
4
3
7
5
1.Deck
2.Battery
3.ESC
4.Motor Wheels
5.Wheels
6.Power Button
7.Charging Port
1
1.Accelerate/Brake
2.Forward/Backward Switch C
3.Button A/Power Switch
4.Button B for Changing Gears
5.USB Port
6.Board Power Indicator
7.Signal Indicator
8.Remote Power Indicator
2
3
4
6 7 8
5

www.ownboard.net 5
Charging Port Power Button
Features and Specs
Accelerate Brake Direction
Switch
Power Switch
Input:100V~240V Wheel High-elastic PU wheel 85A 90*52mm
50Hz/60Hz Max Climb 30%
Output: 41.5V 2A (41.5V 3A for Sanyo) Fast Mode ~25mph(~40Km/h)
Charger
Parameters
Charging Time:3~4 Hours
FOC control, waterproof & shockproof
Middle Mode(only three
speed modes have) ~18.75mph(~30Km/h)
2.4G Wireless Remote
Speed Mode
Slow Mode ~12.5mph(~20Km/h)
Remote Battery Capacity: 400mA Samsung 22R 4.0Ah ~11 miles(~15 km)
ESC&Remote
DC 5V Micro 5P (About 40minutes with 1A) Samsung 30Q 6.0Ah ~14 miles(~22.5 km)
Size：90*54mm
Max Range
Sanyo 8.1Ah ~19 miles(~30.5 km)
Material：High-elastic PU wheel 85A
Motor
Parameter Power：250W*2
Measured by 70 kg rider ,and the actual range will be affected by road conditions,
the rider weight, temperature (via affect battery cell performance) .etc

www.ownboard.net
Charging the Battery
Your E-Skateboard comes with a rechargeable lithium ion battery. Before your first ride you must fully charge the
E-Skateboard to fully. For every ride after, charge your E-Skateboard until it is fully charged, and NOT LONGER.
Do not leave any chargers plugged in overnight, or leave it plugged in past the charge time.
1. Plug one end of the power cord into a grounded AC outlet and the other into the E-Skateboard’s Charging Port.
The red charging light on the charger unit will turn on.
2. The red light will turn green once fully charged. Recharge the E-Skateboard after each use.
(Please note:Always plug the charger into the wall first before the device. If the wall outlet doesn’t have power and
you plug the charger into the device first,it will light green,even if the battery is not full.So always plug into the wall
first to make sure there is power)
THE CHARGER OFFERS A CHARGING STATUS ON THE TOP OF THE CHARGER:
CHARGING LIGHT RED: Battery is charging.
CHARGING LIGHT GREEN: Charging is complete.
When you are done charging the battery, remember to cover the Charging Port.
Don’t use the E-Skateboard if the battery emits strange odors, overheats, or begins leaking. If the battery does leak,
do not touch any leaking materials, as the battery contains dangerous substances. Do not open the battery and do
not insert anything into the battery.
Only use the provided charger for the E-Skateboard. Do not charge the battery if it has over-discharged. It should
be discarded for your safety. Do not turn on the E-Skateboard while it is charging.
To charge your Remote Control, plug the charging cable into a USB port, then plug into the Remote Control’s
Charging Port. When the Charge Light is on, the Remote Control is successfully charging. The Charging Indicator
Light on the Remote Control will turn RED when charging, and will turn to GREEN when fully charged.
NOTE: The remote should be charged within 5 V ,1 A charger, or you can use the computer
USB interface to charge it, Charging voltage over 5 V will do harm to the remote battery.
6

www.ownboard.net
Power Indicators
7
POWER INDICATORS:
Remote Power Indicator (a single LED): after the remote is powered on, if it detects the power is less than 25%
(which can barely support an one-hour operation), the Remote Power LED comes on Red; if the power is sufficient
(that is the power can support an operation of at least one hour), then the Remote Power LED comes on Green.
If there is only 5% of power (which can only support a 15-minute operation) left, the remote will vibrate a double,
long vibration (vibrate for 0.5 second, pause for 0.5 second and then vibrate again for 0.5 second ) and the Remote
Power LED starts to flash Red slowly (once a second); if there is only 2.5% of power left, the remote will vibrate a
double, long vibration again (the same as the previous) and the Remote Power LED starts to flash Red slowly; and
if the power is below the regulated value (3.4V) for safe use and the board stops, the remote will vibrate a short
vibration and then turn off automatically.
Board Power Indicator (4 LEDs in a row): one LED comes on to indicate there is still 25% of power, one LED flashes
to indicate there is only 12.5% of power left. For example, if the power ranges from 62.5% to 75%, then the four
LEDs will display in this way “○●●●”; if the power ranges from 50%~62.5%, then the four LEDs will display in this
way “○○●●”; if the power is below 25%, the remote will vibrate a double, long vibration and the four LEDs will display
in this way “○○○●” ; if the power is below 12.5%, the remote will vibrate a double, long vibration and the four LEDs
will display in this way “○○○○”; and if the voltage goes below the regulated value for safe use, then the power output
will be cut off. At this time, it’s better to stop using as soon as possible.
Notes: the remote will display the power of the remote & the board for 2 seconds and then stop when it’s powered
on and connected to the board. Press the Button A at any time can re-trigger the display of the power of the remote
& the board. the remote only displays the power of the remote when the board is not connected (to the remote).
Attention! “●” means “solid”, “☉” means “flash” and “○” means “die out”.

www.ownboard.net
Operating the E-Skateboard
8
TURNING ON:(With the remote powered off), press the “Button A” (on the remote) for 1 second, the remote vibrates
a short vibration, enters the connecting mode, and the signal LED starts to flash Red slowly (once a second). (With
the board powered off), press the “Power” button on the board (for 0.2 second) to enter the “connecting” mode, and
the Red LED on it starts to flash slowly (once a second).
Note: the signal LED on the remote and the Red LED on the board turn solid after they are connected to each other.
TURNING OFF: manually: (with the remote & the board powered on), pressing the “Button A” on the remote for 2
seconds can turn off the remote, the remote will vibrate a short vibration after the press; pressing the “Power” button
on the board for 1 second can turn off the board.
Note: if the remote is still on after the board is turned off, the signal LED on the remote will flash Red slowly and
vibrate once to remind the user. Similarly, if the board is still on after the remote is powered off, the Red LED on the
board will flash slowly (to warn the user.)
RURNING OFF Automatically: if the user let the board stay still with no further operation for 5 minutes, then the
remote and the board will turn off automatically.
PAIRING THE REMOTE CONTROL AND E-Skateboard( Remote & Board are bound before leaving the factory)
(With the remote & the board powered off,) press the “Power” button on the board for 5 seconds, the Red LED (on
it) starts to flash rapidly to indicate that the board enters the binding mode; then press the “Button A” on the remote
for 5 seconds, the Signal LED (on it) starts to flash Red rapidly to indicate that the remote enters the binding mode,
and the remote vibrates two short vibrations and one long vibration to indicate that the binding succeeds. The signal
LED on the remote and the Red LED on the board turn solid when the binding succeeds.
Note: when using a new remote and a new board, there is no need to press either the Power button (on the board) or
the Button A (on the remote) for 5 seconds to bind them. They enters into the binding mode when they are powered on.

www.ownboard.net
Operating the E-Skateboard
9
Throttle/Brake Control:
User can move the “throttle scroll wheel” forward to speed up, and move it backward to brake.
Notes: Do not move the “throttle scroll wheel” when pressing the Button A (/Power Switch). If you see the four LEDs
(on the remote) flash in the following way: “●○○●”, “○●●○”, “●○○●”, “○●●○”..., then please check if the “throttle scroll
wheel” is at the neutral/zero throttle position.
Switch of Skateboard Direction:
When the board is moving forward, if the user moves the Switch C backward, the remote will vibrate a single, short
vibration (0.1 second), the four LEDs will flash one by one from front to back to indicate the “Backward mode”. When
the board is moving backward, if the user moves the Switch C forward, the remote will vibrate a single, short vibration,
the four LEDs will flash one by one from back to front to indicate the “Forward mode”.
Note: this operation effects only when the “throttle scroll wheel” is at the neutral position.
Switch of Gears:
There are two gears available for the E-Skateboard: 1st gear & 2nd gear.
In 1st gear, the speed ranges from 0 to 20km per hour; in 2nd gear, the speed ranges from 0 to 38km per hour.
When in 1st gear, if press the Button B, the remote will vibrate a single, short vibration, the four board power LEDs
will flash one by one from one end to the other end to indicate that the board is in 2nd gear now.
When in 2nd gear, if press the Button B, the remote will vibrate a single, short vibration, the four board power LEDs
will flash one by one from one end to the other end to indicate that the board is in 1st gear now.
Note: this operation effects only when the “throttle scroll wheel” is at the neutral position. The specific gear and speed
can be adjusted by the specific ESC the user uses.

www.ownboard.net
Safe Riding
10
HELMET: Most serious injuries that occur while riding are head injuries.This could be prevented by wearing a helmet.
ELBOW AND KNEE PADS: For added protection, always wear elbow and knee pads when riding your E-Skateboard,
to prevent any serious injuries.
Get to know the E-Skateboard before riding it. Test your control over it. Make your turns slowly and cautiously, and
give yourself stopping distance.It is recommended you practice your first ride on the E-Skateboard in an open space
with no obstacles to disturb you.
RIDING TECHNIQUE
Foot Position: Keep one foot behind the other, (it’s more comfortable to place one foot forward and the other one
turned 70-90). It will help you gain more stability.
PLEASE NOTE: Riding, like most sports, involves risk of injury and damage. By choosing to ride the E-Skateboard
the responsibility and all inherent risk is on you. It is crucial that you know, understand and act according to safety
rules.
Turns: The turns on the E-Skateboard are commanded by the direction you lean on the Deck.
SPEED MODE
Press the Speed Mode Button to cycle through the 2 different modes (Beginner, and Advanced). Some series have
3 speed modes(Fast, Middle, Slow) It is recommended you start with Beginner or Slow mode.

www.ownboard.net
Care and Maintenance
11
RIDING RANGE
The maximum range of the E-Skateboard is measured on 70KG rider on the flat road. However,a lot of factors will
affect how far you can go per charge:
• Driving Surface:A smooth,flat surface will increase driving distance.
• Weight: More weight means less distance.
• Ambient Temperature: Please ride and store the E-Skateboard under recommended temperature, which will
increase its longevity and driving distance.
• Maintenance: Timely battery charging and maintenance will increase driving distance.
• Speed and Driving Style: Maintaining a moderate speed will increase distance. Frequent starting and stopping,
acceleration,and decelertion will reduce it.
SPEED LIMIT
The top speed of the E-Skateboard is set to 40Km/h (25mph).
WEIGHT LIMIT
The maximum load is 120Kg ( 265lbs). W1A can more load to 150Kg(330lbs)Going above the maximum weight
limit can cause injury or damage the E-Skateboard.
CLEANING THE E-SKATEBOARD
To clean the bottom of the Deck and the Wheels, carefully wipe with a damp cloth, then dry with a dry cloth. Do not
wipe down the top of the Deck. Do not use water to clean the E-Skateboard, as the electrical and electronic systems
may get wet, resulting in personal injury or malfunction of the E-Skateboard.

www.ownboard.net
Care and Maintenance
12
BATTERY
• Keep the E-Skateboard away from fire and excessive heat.
• To avoid damage to the battery, never subject the E-Skateboard to intense physical shock,severe vibration, or
impact.
• Protect the E-Skateboard from water or moisture.
• Never disassemble the E-Skateboard or its battery.
• If there are any issues with the battery, please contact OWNBOARD Customer Support or email us at
[email protected]
STORAGE
• If you plan on storing the E-Skateboard for a substantial period of time, please make sure you fully charge
the battery before storing.The battery should be fully charged once a month after this.
• To protect against dust, cover the E-Skateboard.
• Store the E-Skateboard indoors, in a dry place and at a suitable temperature.
• You should bring the E-Skateboard into a warm environment (above 50 degrees Fahrenheit) for charging.
• Do not leave the E-Skateboard plugged into the charger for long periods of time.

www.ownboard.net
Safety Warnings
13
Here are some useful tips to make sure you always have a safe ride:
• Children, the elderly, and pregnant women should not use the E-Skateboard.
• Do not ride after drinking or taking prescription medication.
• Do not carry items when riding.
• Prior to each ride, inspect each part of the E-Skateboard to ensure it has been maintained correctly and is
functioning properly.
• Always give way to pedestrians.
• Always comply with local traffic laws and regulations.Remember,the E-Skateboard is a motor vehicle, and is
treated as such by local law enforcement. You can and will be arrested for drunk driving. Many cities have
restrictions on where you can drive motor vehicles, as well as additional restrictions on driving non-automobiles
on streets and highways.
• Be alert to things in front and far away from you.
• Make sure your feet are always placed securely on the deck.
•The E-Skateboard cannot be ridden by more than one person.Only one person can ride at a time.
• When you ride the E-Skateboard along with other riders, always keep a safe distance to avoid a collision.
• When turning, be sure to maintain your balance.
• Do not allow distractions when riding, such as answering the phone or engaging in any other activities.
• Avoid riding in the rain or on smooth surfaces such as snow or ice.
• Do not ride on roads with obstacles (such as litter, small stones, etc.).
• Avoid riding in narrow spaces or on steep slopes.
• Avoid riding around flammable gas,steam,liquid,or dust that could cause fire.
• Never operate the product barefooted and keep shoelaces tied.

www.ownboard.net
Safety Warnings
14
MODIFICATIONS
Do not attempt to disassemble, modify, repair, or replace the E-Skateboard or any components of the unit without
instruction from OWNBOARD Customer Support. This will void any warranty, and can lead to malfunctions which
may cause injury.
ADDITIONAL OPERATION CAUTIONS
Do not lift the E-Skateboard off the ground while it is on and the wheels are in motion. This can result in freely
spinning wheels, which may cause injury to yourself or others nearby. Do not jump on or off the E-Skateboard,
and do not jump while using it. Always keep your feet firmly planted on the deck while in operation.Always check
battery charge before using.

www.ownboard.net
Warranty
15
TO QUALIFY FOR WARRANTY SERVICE:
All Ownboard Boards come standard with a 90-Day Warranty which covers any manufacturing defects.
Ownboard boards are built using the best configuration of motors, controllers, and batteries. We test all individual
parts and run each Ownboard Board for 210 minutes before packaging it up for shipment.
All components, such an extra charger or battery can be purchased separately in our shop. If not, please contact
[email protected]. The Ownboard board can be easily repaired by replacing the broken part. We will always
diagnose and send free replacement parts for boards under warranty, shipping fees will be collected.
We are responsible for diagnose and sending free parts until the board is fixed. For example, if we sent a battery
and problem still exists, we will keep sending ESC, Remote, Motors whatever needed, until the moment the right
part is replaced and the board is fixed.
We reply to all questions within 1-4 days. You can get replacement parts within 3-8 days if there is ever an issue
with your board.
Refund Policy
We don't refund when your ordered products are being built.
We don't refund when your order is shipped out.
We don't refund when there is an issue with the product you received.
We don't accept returns.
Warranty Statement
1. the warranty clause is only applicable to OWNBOARD E-SKATEBOARD, and the warranty is not responsible
for the products purchased by unauthorized sellers or other channels.
2. the specifications, colors, and configuration of the products are all subject to the object.

FACEBOOK WEBSITE