Oxdale se400 Operating instructions

1
OXDALE PRODUCT LTD
OPERATING AND MAINTENANCE MANUAL
SE400 LOG SPLITTER
KEEP FOR FUTURE USE

2
CONTENTS
Safety
3
Labels
6
Quick Guide
7
In Depth Instructions
9
Warranty Information
16
Technical Specifications
17
Declaration of Conformity
18
Contact Details
19
Other Information
Manufacturer
Oxdale Products
Unit 20 –21 Foxwood Road
Off Sheepbridge Lane
Chesterfield S41 9RF
Year of Construction
2019
Machinery Type
SE400
Mass of Machine
Serial Number
Max. Hydraulic Oil
Operating Pressure

3
SAFETY
OXDALE PRODUCRS REQUIRES THAT ANYONE OPERATING OR
MAINTAINING THE LOG SPLITTER SHALL READ AND UNDERSTAND
ALL SAFETY, OPERATION AND MAINTENANCE DATA CONTAINED IN
THIS USER MANUAL BEFORE USING THE LOG SPLITTER.
The log splitter is powered by a Honda Engine. A copy of the
Honda owner’s manual should accompany this instruction
manual. Please contact us if this is missing. Hydraulic action
provides the force to drive a splitting wedge into a log. Never
operate the logsplitter persons are in the area, especially small
children. Hazards associated with log splitting may be pinch
points, splinters, eye injury and entanglement.
IT IS FOR SINGLE PERSON USE ONLY.
YOU ARE RESPONSIBLE FOR THE SAFE OPERATION AND
MAINTENANCE OF THE LOG SPLITTER. THE MOST IMPORTANT
SAFETY DEVICE ON THE EQUIPMENT IS THE SAFE OPERATOR.
•Keep two hands on the operating leavers at all time,
never put hands or fingers between the wedge and the
log to be split or near moving parts. Always stop the
machine before cleaning it or making adjustments.
•The operator should wear suitable PPE including eye
protection, gloves and safety boots. Close fitting
clothing should be worn to reduce the risk of
entanglement.
•Never stand either side of the log splitter whilst
operating. Logs can sometimes split apart violently e.g.
due to knots. Stand in front of the machine to minimise
risk from falling debris.

4
•Never hold the top of the log whilst setting in place or
splitting.
•Never split two logs on top of each other.
•The log splitter is very powerful but some hard or wet
wood can be difficult to split. Do not force the wedge as
this could cause injury to yourself and cause damage to
the log splitter.
•Never operate the splitter when children or animals are
in the danger zones or let children operate the splitter.
•Do not leave machinery unattended whist it is running.
•Both ends of each log should be cut as square as possible
to help prevent the log from riding out of the splitter.
This is also aided by the three holes in the log platform
having raised edges to reduce the risk of slipping.
•Always choose a working area free from obstructions
and then keep the working area free from obstructions
such as logs and split wood.
•Machine is for single person operation only using both
hands on the operating lever.
•Operate splitter on solid ground level.
•The log splitter is designed only for splitting wood. Using
it for any other purpose may damage it and be
dangerous to the user and others.
•Ensure that the machine is stable and secure at all times
when in use and is stored safely when not in use in a dry
place.
•Ensure that the accompanying Honda engine manual
and its safety decals are referred to.

5
LABELS
The SE400 log splitter should have the following labels
attached. If any safety decals are missing or illegible, they
should be replaced immediately.
SAFETY LABELS
“Danger! Keep clear of moving parts!”
Always keep hands and any loose clothing out of
the way of moving parts, especially the splitting
wedge.
“Wear eye protection!”
Splitting logs carries the risk of flying debris,
always wear eye protection.
“wear gloves!”
Log splitting can involve contact with sharp
objects, suitable gloves should always be worn.
“Wear appropriate footwear!”
Steel toecap boots should always be worn due to
potential for heavy objects to fall off the splitter
“Wear hearing protection!”
Operators are required to wear hearing protection
conforming to current standards.

6
OPERATORS QUICK GUIDE
It is important for the safety of the operator and the
machine to follow these instructions
PLEASE REFER TO IN DEPTH INSTRUCTONS BEFORE FIRST USE
Pre-Operation Checklist
•Grease the slider every 10 hours of operation and
pre/post season.
•Check that all hydraulic fittings and connections are
tight and in good condition.
•Check for damaged, worn, missing parts and replace if
necessary.
•Replace missing or illegible safety decals.
•Inspect the log holding device for damage
Operating Checklist
•Position the log splitter on solid level ground when
operating.
•Start the engine and adjust the throttle to suit the
work being done (check the engine manual for
details.)
•Position the log on the operating table so it is lined up
with the centre of the wedge
•Secure the log firmly using the log holding device
•Using both hands lift the safety leavers to lower the
wedge to split the log. The speed can be controlled by
how much pressure you put on the control valve.
•Using both hands, lower the operating leavers to lift
the ram back to the desired height

7
•Stop splitting if the log starts to move and reposition
as per the above instructions.
•Should the wedge lock or become stuck in the log,
return the wedge to the fully open position and gently
rock the log free before continuing.
Post Operating Checks and Maintenance Instructions
•Wipe off your log splitter with a damp cloth
periodically to keep it free of debris.
•It is recommended that you store your splitter in a dry
place when not in use.
•The splitting wedge may need to be sharpened
periodically, just using a file.
•Inspect the log holding device for damage.
Storage and Transportation
•The SE400 should be stored in an upright, vertical
position.
•Should be stored in a dry location.
•Should be stored in a safe location where the machine
will not get knocked over.
•The SE400 should be transported in a vertical position
and should be strapped securely.

8
IN DEPTH INSTRUCTIONS
Before First Use
FILL THE ENGINE WITH ENGINE OIL AND PETROL
The engine will contain oil however the level should be tested
before use.
Before the engine can be started for the first time it needs to
be filled with petrol. Please refer to the Honda engine manual
for details on how to fill the engine with oil and petrol.
PETROL FILLER CAP
OIL FILLER CAP
Filling the Tank with Hydraulic Oil
The hydraulic oil tank holds approximately 14 litres of
hydraulic oil. We recommend using ISO 46 type oil. The tank is
filled through the filler cap on top of the unit.
Pour the oil in until you have filled the tank as indicated on the
level gauge.

9
Please note that once the unit has been run for the first time
and the pump filter and pipe work filled, you will need to top
up the tank.
FILLER CAP
LEVEL GAUGE
GREASING
The ram collar needs to be greased
where it slides down the guide; this
will help reduce the friction and
help the unit run more smoothly.
This needs to be carried out every
10 hours or alternativly at the start
of each day.
Ram Collar

10
Operating Instructions
These instructions are designed for the safety of the
operator and the machine
The log splitter is designed for splitting logs only AND IS FOR
SINGLE PERSON USE. It can handle logs no bigger than 450mm
and having a diameter no bigger than 900mm and no smaller
that 75mm in diameter.
Only persons who are competent to do so and having read this
manual, in full, should use the log splitter.
Before using the log splitter for the first time each day a visual
inspection should be carried out as explained in the operators
guide.
When operating the unit, it should be positioned on solid and
as far as possible, level ground. Wheel blocks should be used
to prevent movement of the machine. Both hands should be
kept on the leavers when the ram is being extended and
retracted. Lifting the handle will extend the ram and lowering
the handle will retract the ram.

11
Log holding device
Pick the log to be split. This should have
been cut square at both ends. This is very
important as it will reduce the chance that
the log will slip.
Position the log under the point of the
wedge, unhook the chain on the log
holding device and pass round the log
before hooking back in place
Place both hands on the operating leavers
and lift to lower the wedge into the log.
Stop lowering the wedge if the log starts to go sideways and
reposition. If the wedge gets stuck, return the wedge to the
fully open position and rock the log free before continuing.
Use both hands to push the operating leavers down and return
the wedge back to the desired height.
When splitting wood always stand in front of the unit and not
to the side as logs can split with some force and be thrown off
the unit to the sides. Always keep other people and
pets/animals out of the area when splitting logs.

12
With both hands, clasp both leavers
and push up to lower the wedge
Using both hands, pull the leavers down
to lift the wedge
Let go of the leavers or return them to
the neutral position to stop the
wedge

13
POST OPERATING CHECKS AND MAINTENANCE GUIDE
The machine must be switched off before any cleaning or
adjustments are carried out. The removal of wood chips etc
from the unit and the removal of contaminated grease from
the wedge collar is strongly advised.
Sharpen the wedge as and when required. This can be done
with a file.
Check for any loose bolts or any other damage at regular
intervals.
If the log splitter is going to be stored then this should be in a
dry location in the upright, vertical position.
Hydraulic System
Periodically check the hydraulic oil level with the gauge on the
side of the unit and top if required.
Check for oil leaks, worn hoses and
loose fittings. The pressure in the
hydraulic system can exceed 2000 PSI.
Reinforced hoses can develop pin hole
leaks and hydraulic connections can
vibrate loose. Hydraulic leaks may be
hard to see. Never check for leaks with your hand as the high
pressure can inject oil under the skin. This is a medical
emergency and if this happens immediate medical attention
must be sought.

14
Please be aware that hoses and fittings can be become very
hot from heavy use and should be checked with caution. Place
your hand near the connection to sense for heat before
touching the connection. If the area is hot you should allow it
to cool down before touching any heated connections.
Hydraulic pumps and control valves operate with minute
clearances (tolerances.) Grit, grime and dirt pushed through
these openings can eventually wear the surfaces and damage
the system.
Clean hydraulic oil must be used. The fill area and
connections must be kept clean as well. Dirt is
the greatest source of hydraulic system damage.
Filter Element Replacement
Remove the top cover on the filter body and
using the handle on top of the filter remove this
from the filter body. To replace this, reverse the
removal process.
Looking after the hydraulic oil is very important. This
keeps the oil free from contamination and will
reduce the need to change the oil.
If you need to change the oil you can drain the oil through the
feed pipe to the pump. Remove the pipe from the pump and
drain the oil into a suitable container. If you are replacing the
oil then you will also need to replace the filter element.
Replace the filter before refilling the oil tank. Check the oil
level once the machine has been run and top up as required.

15
WARRANTY INFORMATION
Warranty claims which arrive because of incorrect operation,
insufficient maintenance or the use of non –approved
consumables e.g. lubricants and hydraulic oils will not be
accepted by the manufacturer.
Only original Oxdale parts may be used. When ordered
replacement parts please provide the model name and
number. Pressure adjustments to the valves must only be
carried out by Oxdale authorised dealers.
No liability is accepted for damage caused by Oxdale products
in so far as they are caused by incorrect repairs or the non –
use of original Oxdale replacement parts or in so far as repairs
have not been carried out by Oxdale or a pre –authorised
specialist, The same applied to auxiliary parts and accessories.
All warranty claims are on a return to manufacturer basis.

16
TECHNICAL SPECIFICATIONS –SE400
Log Splitter
Log Splitter Ram
Model No
Weight
101kg
Max pressure
4780psi/330bar
Ram Bore Diam.
60mm
Ram Stroke
400mm
Ram Rod Diam.
40mm
Engine
Honda GX200
Pump
Saturn Group 2 E-
10-N
HP
5.5 at 3600rpm
Input Speed
3000rpm
Fuel Cons.
1.9 L/hr
Torque
33n/m
Noise Level
92 db (A)
Displacement
5 cc/rev
Flow
1.5 l/min
Max Cont.Pressure
250bar
3625psi
Max Peak. Pressure
290 bar
4200 psi
Filter
MP Filtri
MPF0301AG-
1P25NB
Spool Block
MB2
Type
Return
Max Cont.Pressure
250bar
3600psi
Filter Code
0301P25NB
Max Peak Pressure
320bar
4600psi
Max Back Pressure on
Port T
30bar
430 psi
Port Marked P
Pressure Line
Port Marked T
Exhaust Line
Relief Valve Setting
220bar
3150psi

17

18
Oxdale Products
Units 20 –21 Foxwood Road
Off Sheepbridge Lane
Chesterfield
Derbyshire
S41 9RF
Tel: [phone]
Email: [e-mail]
Web: www.oxdaleproducts.co.uk
Registered Address:
Oxcroft Stables
30 Oxcroft Estate
Stanfree
Derbyshire
S44 6AU
Company Number: 6490139 England & Wales

19
RELATED PRODUCTS
Sawbench
Available as Electric (240v) or PTO.
Electric –Swinging cradle, 600mm blade,
cuts logs up to 10” diameter.
PTO –Grizzly 700R has a swinging cradle, suitable for logging,
balanced blade for smooth and efficient cutting, 700mm blade
which cuts lots up to 12” diameter.
Log Grab
Available in two
sizes (42cm and
70 cm log
diameter.)
Rear Mounted Crane
Ideal for lifting and moving heavy
items behind your tractor and is
available with or without lifting
chains and timber grab.

20
NOTES