Ozito Ecomow ECO-320 User manual

Rated power: 1100W
Rated voltage and frequency: 240V ~ 50Hz
No Load Speed: 3000 /min
Cutting Diameter: 320mm
Cutting Heights: 31mm, 47mm, 63mm
Protection against ingress of water: IPX4
1. Start/stop lever
2. Upper handle
3. Handle securing knob
4. Catcher flap
5. Lower handle
6. Wheels
3
6
7
2
7. Wheel hub
8. Lower handle securing point
9. Grass catcher
10. Cord clips
11. Cord retainer
12. Lock-off button
10
8
9
4
5
12
1
11
2
SPECIFICATIONS
KNOW YOUR PRODUCT

3
TABLE OF CONTENTS
SPECIFICATIONS…………………………………………
KNOW YOUR PRODUCT…………………………………
INTRODUCTION…………………………………………
SAFETY INSTRUCTIONS………………………………..
ASSEMBLY ………………………………………………..
FITTING WHEELS………………………………………...
FITTING LOWER HANDLES……………………………
FITTING AND USING CORD RETAINER………………
FITTING UPPER HANDLE……………………………….
GRASS CATCHER………………………………………..
HOW TO MOW…………………………………………..
ON / OFF SWITCH……………………………………….
ADJUSTING CUTTING HEIGHT………………………..
REMOVING AND FITTING THE BLADE………………
MAINTENANCE …………….……………………………
DESCRIPTION OF SYMBOLS…….….….….….……….
PACK CONTENTS………………………………………..
WARRANTY……………………………………………….
Page 2
Page 2
Page 4
Page 4
Page 8
Page 8
Page 9
Page 10
Page 10
Page 10
Page 12
Page 12
Page 13
Page 13
Page 14
Page 14
Page 15
Page 16

INTRODUCTION
SAFETY INSTRUCTIONS
ELECTRICAL SAFETY
4
Congratulations on purchasing an Ozito Lawn mower.
We aim to provide quality tools at an affordable price.
We hope you will enjoy using this tool for many years.
Your Ozito Ecomow Electric Mower ECO-320 has been
designed for small to medium sized lawns and is for
DIY purposes only.
WARNING! When using mains-powered tools, basic safety precautions
including the following should always be followed to reduce risk of fire, electric
shock, personal injury and material damage.
Read the whole manual carefully and make sure you know how to switch the tool
off, in an emergency, before operating the tool.
Save these instructions and other documents supplied with this machine for
future reference.
The electric motor has been designed for one voltage only. Always check that the
power supply corresponds to the voltage on the rating plate.
This tool is double insulated in accordance with AS/NZS 60335-2; therefore
no earth wire is required. If the supply cord is damaged, it must be replaced
by an electrician or a power tool repairer in order to avoid a hazard.
1. Before use, examine cord for damage; replace it if there are signs of damage
or ageing.
2. Do not use the lawn mower if the electric cables are damaged or worn.
3. Immediately disconnect from the mains electricity supply if the cord is cut,
or the insulation is damaged. Do not touch the electric cord until the electricity
supply has been disconnected. Do not repair a cut or damaged cord; replace
it with a new one.
4. Your extension lead must be unwound, coiled leads can overheat and reduce
the efficiency of your mower.
5. Keep lead away from lawn mower; always work away from the power point
mowing up and down never in circles.
6. Do not pull lead around sharp objects.
7. Always switch off at the mains before disconnecting any plug, cord or extension lead.
8. Never carry the product by the cord.

5
1. This appliance is not intended for use by young children or infirmed persons unless
they have been adequately supervised by a responsible person to ensure that they
can use the appliance safely.
2. Only use the lawn mower in the manner and for the functions described in
these instructions.
3. Never operate the lawn mower when you are tired, ill or under the influence of
drugs, alcohol or medicine.
4. The operator or user is responsible for accidents or hazards occurring to other
people or their property.
5. Use the lawn mower only in daylight or good artificial light.
6. Avoid operating your lawn mower in wet grass, where feasible.
7. Take care in wet grass, you may loose your footing.
8. On slopes be extra careful of your footing and wear non-slip footwear.
9. Mow across the face of slopes, never up and down.
10. Exercise extreme caution when changing direction on slopes. Walk never run.
11. Mowing on banks and slopes can be dangerous. Do not mow on banks or
steep slopes.
12. Do not walk backwards when mowing, you could trip.
13. Never cut grass by pulling the mower towards you.
14. Switch off before pushing the mower over surfaces other than grass.
15. Never operate the lawn mower with damaged guards or without guards in place.
16. Keep hands and feet away from the blade at all times and especially when
switching on the motor.
17. Young children should be supervised to ensure that they do not play with
the appliance.
18. No one is to operate this appliance without reading and understanding these
operating instructions.
GENERAL
ELECTRICAL SAFETY (cont.)
9. Never pull on the cord to disconnect any of the plugs.
10. Use only AC mains supply voltage shown on the product rating label.
11. It is recommended that the appliance should by supplied via a residual current
device (RCD) with a tripping current of not more than 30 mA.
12. Use at least a 10 Amp rated 1.0 mm2extension cord with a maximum of 25 meters
and the cord shall be not lighter than:
- If rubber insulated, ordinary tough rubber sheathed flexible cord (code
designation 60245 IEC 53);
- If polyvinyl chloride insulated, ordinary polyvinyl chloride sheathed flexible
cord (code designation 60227 IEC 53);

If not used properly this lawn mower can be dangerous! This lawn mower
can cause serious injury to the operator and others, the warnings and
safety instructions must be followed to ensure reasonable safety and
efficiency in using this lawn mower. The operator is responsible for
following the warning and safety and instructions in this manual and
on the lawn mower. Never use the mower unless the catcher or guards
provided by the manufacturer are in the correct position.
6
GENERAL (cont.)
ADDITIONAL SAFETY RULES FOR LAWN MOWERS
19. Do not tilt the lawn mower when the motor is running, except when starting or
stopping. In this case, do not tilt more than absolutely necessary and lift only
the part which is away from the operator. Always ensure that both hands are in
the operating position before returning the appliance to the ground.
20. Do not put hands near the grass discharge chute.
21. Never pick up or carry a mower when it is operating or still connected to the
mains supply.
22. Remove the plug from the mains:
- before leaving the mower unattended for any period
- before clearing a blockage
- before checking, cleaning or working on the appliance
- if you hit an object. Do not use your lawn mower until you are sure that
the entire lawn mower is in a safe operating condition
- if the lawn mower starts to vibrate abnormally. Check immediately.
Excessive vibration can cause injury.
Explanation of Symbols on the Ecomow Electric Mower - ECO-320
WARNING
Read the user instructions carefully to make sure you understand all
the controls and what they do.
Always keep the lawn mower on the ground when mowing.
Tilting or lifting the lawn mower may cause stones to be thrown out.
Keep bystanders away. Do not mow whilst people especially
children or pets are in the mowing area.
Switch Off! Remove plug from mains before adjusting, cleaning or
if cable is entangled or damaged. Keep the cable away from
the blade.
!
!
!
!
!
!
!
!
!
!
!
!

Beware of severing toes or hands. Do not put hands or feet near
a rotating blade.
Blade continues to rotate after the machine is switched off. Wait until
all machine components have completely stopped before touching them.
Do not mow in the rain or leave the lawn mower outdoors while raining.
1) Training
•Read the instructions carefully. Be familiar with the controls and the proper use of
the appliance.
•Never allow children or people unfamiliar with these instructions to use the
appliance. Local regulations may restrict the age of the operator.
•Never mow while people, especially children, or pets are nearby.
•The operator or user is responsible for accidents or hazards occurring to other
people or their property.
2) Preparation
•While mowing, always wear substantial footwear and long trousers.
•Do not operate the appliance when barefoot or wearing open sandals.
•Thoroughly inspect the area where the appliance is to be used and remove all
stones, sticks, wires, bones, and other foreign objects.
•Before using, always visually inspect to see that the blades, blade bolts and cutter
assembly are not worn or damaged. Replace worn or damaged blades and bolts in
sets to preserve balance.
•On multi-bladed appliances, take care as rotating one blade can cause other
blades to rotate.
3) Operation
•Mow only in daylight or in good artificial light.
•Avoid operating the appliance in wet grass, where feasible.
•Always be sure of your footing on slopes.
•Walk, never run.
•For wheeled rotary mowers, mow across the face of slopes, never up and down.
•Exercise extreme caution when changing direction on slopes.
•Do not mow excessively steep slopes.
•Use extreme caution when reversing or pulling the appliance towards you.
•Stop the blade(s) if the appliance has to be tilted for transportation when crossing
surfaces other than grass, and when transporting the appliance to and from the
area to be mowed.
•Never operate the appliance with defective guards or shields, or without safety
devices, for example deflectors and/or grass catchers, in place.
ADDITIONAL SAFETY RULES FOR LAWN MOWERS (cont.)
7
!
!
!
!
!
!

8
ADDITIONAL SAFETY RULES FOR LAWN MOWERS (cont.)
•Switch on the motor according to instructions and with feet well away from
the blade(s).
•Do not tilt the appliance when switching on the motor, except if the appliance
has to be tilted for starting. In this case, do not tilt it more than absolutely
necessary and lift only the part which is away from the operator. Always ensure
that both hands are in the operating position before returning the appliance to
the ground.
•Do not put hands or feet near or under rotating parts. For rotary mowers, keep
clear of the discharge opening at all times.
•Never pick up or carry an appliance while the motor is running.
•Pull the plug from the socket:
- whenever you leave the machine;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- after striking a foreign object. Inspect the appliance for damage and make
repairs as necessary;
- if the appliance starts to vibrate abnormally (check immediately).
4) Maintenance and storage
•Keep all nuts, bolts, and screws tight to be sure the appliance is in safe
working condition.
•Check the grass catcher frequently for wear or deterioration.
•Replace worn or damaged parts for safety.
•For cylinder mowers, be careful during adjustment of the appliance to prevent
entrapment of the fingers between moving blades and fixed parts of the appliance.
Fitting the Wheels
1. Remove the body of the lawn mower from the
packaging and place on a flat surface.
2. Slide all four wheels (6) over the axle pins on
each corner of the mower body.
ASSEMBLY

9
3. Slide split pins (supplied) through each hole in
the four axle pins which are protruding through
the wheels (6).
4. Bend the two ends of each split pin backwards
around the axle pin to secure the wheels (6) to the
mower body.
5. Insert the wheel hub (7) over the wheels (6) and
push them in. This may require a little bit of force.
They are properly assembled to the wheels (6)
when they click into place.
Fitting the Lower Handles to the Mower Body
1. Insert the lower handle (5) into the two holes in
the lower handle securing point (8) of the mower
body. The screw holes in the lower handle (5)
should face outwards.
2. Fit the screw and washer (supplied) through the
hole above the rear wheel, align with the hole in
the lower handle (5) and then secure into place
using a phillips head screwdriver. Repeat the same
to the hole on the opposite rear side of the mower.
ASSEMBLY (cont.)

10
ASSEMBLY (cont.)
Fitting and Using the Cord Retainer
•To fit the cord retainer, slide it over the upper handle
end (on the switch side) before fixing the upper
handle to the lower handles.
•The cord retainer (11) prevents the extension lead
from being disconnected during use. Fit the extension
lead (socket end of lead) through the loop and secure
over the hook as shown in the diagram. Once fitted,
connect the lawn mower power plug into the
extension lead socket.
Fitting the Upper Handle to the Lower Handles
•Place the upper handle (2) over the upper ends
of the lower handles. Fit the bolts through
the inner side of the lower handle (5) and then
through the holes in the upper handle (2).
Secure in place by screwing the handle
securing knobs over the protruding ends of
the bolts.
Securing the Power Cord to the Handle
•Secure the power cord running from the
switch housing to the body of the mower by
using the two cord clips (10) (supplied). Fit
one closer to the mower body end of the
handle, ensure a little slack is left between
the clip and where the cord enters the mower
housing. Fit the other cord clip (10) to the
upper end of the lower handle (5).
Assembling the Grass Catcher
•To assemble the grass catcher (9) align the two
halves and push them together. Ensure the two
halves clip together around the entire
middle section.

ASSEMBLY (cont.)
11
Fitting and removing the grass catcher
•To fit the grass catcher (9) lift up the catcher flap (4).
•Clear out any grass that may be in the grass chute.
Whenever clearing out grass from the grass chute,
the mower must first be turned off and
disconnected from the power supply.
•Guide the two holes on the top of the catcher over
the two raised clips on the mower housing.
•Lower the rest of the grass catcher (9) and allow it to sit in place. Lower the catcher
flap (4).
•To empty the grass catcher (9), lift the flap then lift the catcher flap (4) off the two
raised housings clips.
WARNING! When assembling the grass catcher (9) back to the mower after
emptying, always ensure there is no build up of grass in the grass chute. If needing to
clear the grass, always ensure the mower is disconnected from the power supply prior
to clearing. A build up of grass in the grass chute may prevent grass from moving into
the grass catcher effectively.
1. While using your lawn mower always wear substantial footwear and long trousers.
2. Make sure the lawn is clear of sticks, stones, wire and debris; they could
be thrown by the blade.
3. Before using the lawn mower and after any impact, check for signs of wear
or damage and repair as necessary.
4. Replace a worn or damaged blade together with the blade bolt to preserve balance.
PREPARATION

CUTTING HEIGHT ADJUSTMENT
12
On/Off Switch
To prevent accidental start up of the motor the mower is designed with a dual action
switch. To start, press the button and pull the lever. The motor automatically stops upon
the releasing the lever.
WARNING! The blade will coast after the switch has been released. Be aware
of the necessary time it takes for the blade to stop coasting. Do not try to stop
the blade from coasting, allow it to stop by itself.
1. For the best results, mow the outside edge of the lawn in a clockwise direction first.
2. Then start mowing the edge of the lawn nearest to the power point so the
lead is laid out on the lawn you have already cut.
3. For best grass collection, always mow in a straight line; do not swing the lawn
mower from side to side.
Do Not Overload the Mower
Mowing long thick grass may cause the motor speed to drop; you will hear a
change in the motor sound. If the motor speed drops you may overload your lawn
mower, which may cause damage. When mowing in long thick grass a first cut with
the cutting height set in the highest position, this will help reduce the load.
ALWAYS HANDLE THE BLADE WITH CARE – SHARP EDGES COULD CAUSE
SERIOUS INJURY. USE GLOVES.
To obtain the desired cutting height, the front and rear axles are repositioned on
the underside of the mower housing.
WARNING! Disconnect the mower from the power supply and ensure
the blade has stopped coasting before adjusting the height.
Adjusting the Front Wheel Cutting Height Position (Fig. a)
1. Turn the mower upside down.
2. Pull the wheel axle towards the front of
the mower.
3. Locate the wheel axle into the desired
cutting height adjustment position.
Note: Make sure that both front right and
left wheel are located in the same cutting
height adjustment position. Fig. a
HOW TO MOW
!
!
!
!

CUTTING HEIGHT ADJUSTMENT (cont.)
Adjusting the Rear Wheel Cutting Height Position (Fig. b)
1. Turn the mower on its side.
2. Pull the rear wheel axle towards the
mower's catcher flap.
3. Locate the wheel axle into the desire
cutting height adjustment position.
Note: Make sure that both rear right and left
wheel are located in the same cutting height
adjustment position.
Cutting Height Positions (Fig. c)
1. 31 mm (lowest cutting height position)
2. 47 mm
3. 63 mm (highest cutting height position)
Note: Disconnect the mower from the power supply and ensure that the
blade has stopped coasting before removing and fitting the blade.
Removing the Blade
1. To remove the blade bolt, hold the fan firmly and with a spanner loosen the blade
bolt by turning it anti-clockwise.
2. Remove the blade bolt, and blade.
3. Inspect for damage and clean as necessary.
Renew your metal blade after 50 hours mowing or 2 years whichever is the
sooner – regardless of condition. If the blade is cracked or damaged replace it
with a new one. Never use a blade bolt if the insulated head is damaged, cracked
or missing.
Fitting the Blade
1. Fit the blade to the fan with the tilt edges of the blade facing towards the mower,
ensuring the blade is located onto the fan location points correctly.
2. Re-assemble blade bolt through blade and fan.
3. Hold the fan firmly and tighten blade bolt with a spanner, by turning in a
clockwise direction.
Do not over tighten.
13
Fig. b
Fig. c

MAINTENANCE
14
1. Keep all nuts, bolts and screws tight to be sure the lawn mower is in a safe
working condition.
2. Check the catcher frequently for wear or deterioration.
3. Replace worn or damaged parts for safety.
4. Only use the replacement blade, blade bolt, and impeller specified for this
product.
5. Be careful during adjustments of the lawn mower to prevent entrapment
of the fingers between moving blade and fixed parts of the machine.
6. Oil the wheel pins.
7. Store the lawn mower in a dry place.
DESCRIPTION OF SYMBOLS
VVolts Hz Hertz
~Alternating current WWatts
/min Revolutions or
reciprocation per minute
Double insulated
n o No load speed
Warning
Read the user instructions carefully to make sure you understand all the controls
and what they do.
Always keep the lawnmower on the ground when mowing.
Tilting or lifting the lawnmower may cause stones to be thrown out.
Keep bystanders away. Do not mow whilst people especially children or pets are
in the mowing area.
Switch Off! Remove plug from mains before adjusting, cleaning or if cable is
entangled or damaged. Keep the cable away from the blade.
Beware of servering toes or hands. Do not put hands or feet near
a rotating blade.
Blade continues to rotate after the machine is switched off. Wait until all machine
components have completely stopped before touching them.
Do not mow in the rain or leave the lawnmower outdoors while raining.
Regulator compliance mark

AUSTRALIA (Head Office)
1 - 23 Letcon Drive, Bangholme, Victoria, Australia 3175
Telephone: [phone]
Facsimile: [phone]
Website: www.ozito.com.au
Email: [email protected]
1 x Lawnmower ECO-320
2 x Lower handles
1 x Upper handle
4 x Wheels
1 x Spanner
2 x Cable clips
2 x Handle bolts & knobs
1 x Cord retainer
4 x Wheel caps
2 x Screws (handle securing)
2 x Washers (handle securing)
4 x Split pins
2 x Catcher halves
1 x Instruction manual
Power tools that are no longer usable should not be
disposed of with household waste but in an environmentally
friendly way. Please recycle where facilities exist. Check with
your local council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in the
environment. Please recycle packaging where facilities exist.
Check with your local council authority for recycling advice.
CARING FOR THE ENVIRONMENT
PACK CONTENTS
OZITO INDUSTRIES PTY LTD
15

2 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 24 months from the original date of purchase
and is intended for DIY (Do It Yourself) use only. If a product is defective it will be replaced in
accordance with the terms of this warranty. Warranty excludes consumable parts, for example:
grass catcher, wheels, blade, cord clips, and all accessories.
WARNING
The following actions will result in the warranty being void.
Professional, Industrial or high frequency use.
If the tool has been operated on a supply voltage other than that specified on the tool.
If the tool shows signs of damage or defects caused by or resulting from abuse, accidents
or alterations.
Failure to perform maintenance as set out within the instruction manual.
If the tool is disassembled or tampered with in any way.
OZITO
Australia/New Zealand (Head Office)
1-23 Letcon Drive, Bangholme, Victoria, Australia 3175
•
•
•
•
•
OW8
WARRANTY
YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER
TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO
YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT.
PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
The benefits provided under this warranty are in addition to other rights and remedies which
are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this warranty,
however, where you have suffered any additional direct loss as a result of a defective product
you may be able to claim such expenses by contacting our customer service helpline above.
` Australia 1800 069 486
New Zealand 0508 069 486