Cordless Drill
7
fl ashing LED on the power tool.
To restart the machine, release the On/Off
switch and then actuate again.
►Rapid shut-off can trigger only when
the power tool is running at maximum
operating speed and can rotate freely
around the drill bit axis. Choose a suit-
able work position for this. Otherwise, rap-
id shut-off will not be ensured.
Working Advice
►Apply the power tool to the screw only
when it is switched off . Rotating tool in-
serts can slip off .
An auxiliary tool can be used to remove the
screwdriver bit or universal bit holder.
Maintenance and Service
Maintenance and Cleaning
►Before any work on the machine itself
(e. g. maintenance, tool change, etc.) as
well as during transport and storage,
remove the battery from the power tool.
There is danger of injury when unintention-
ally actuating the On/Off switch.
►For safe and proper working, always
keep the machine and ventilation slots
clean.
When the battery is no longer operative,
please refer to an authorized after-sales ser-
vice agent for P.I.T. power tools.
Dispose of waste
Damaged power tools, batteries, acces-
sories and waste packaging materials
must be recycled and reused in an envi-
ronmentally friendly manner.
Do not throw power tools and accumulators /
batteries into general household waste!
Product serial number interpretation
serial number
The fi rst and second digits of the product seri-
al number from left to right
Year of production, the third and fourth digits
indicate the month of production, the
The fi fth and sixth digits indicate the produc-
tion day.
TERMS OF WARRANTY SERVICE
1. This Warranty Certifi cate is the only docu-
ment that confi rms your right to free warranty
service. Without presenting this certifi cate, no
claims are accepted. In case of loss or dam-
age, the warranty certifi cate is not restored.
2. The warranty period for the electric ma-
chine is 12 months from the date of sale,
during the warranty period the service depart-
ment eliminates manufacturing defects and
replaces parts that have failed due to the fault
of the manufacturer free of charge. In the war-
ranty repair, an equivalent operable product
is not provided. Replaceable parts become
property of service providers.
P.I.T is not liable for any damage that may be
caused by operation of the electric machine.
3. Only clean tool accompanied with the
following duly executed documents: this War-
ranty Certifi cate, Warranty Card, with all fi elds
fi lled out, bearing the stamp of the trade orga-
nization and the signature of the buyer, shall
be accepted for warranty repair.
4. Warranty repair is not performed in the fol-
lowing cases:
- in the absence of a Warranty Certifi cate and
a Warranty Card or their incorrect execution;
- with failure of both a rotor and a stator of the
electric engine, charring or melting of primary
winding of the welding machine transformer,
charging or starting-charging device, with in-
ternal parts melting, burn down of electronic
circuit boards;
- if a Warranty Certifi cate or a Warranty Card
does not correspond to this electric machine
or to the form established by the supplier;
- upon expiration of the warranty period;
- at attempts of opening or repair of the elec-
tric machine outside the warranty workshop;
making constructive changes and lubrication
of the tool during the warranty period, as ev-
idenced, for example, by the creases on the
spline parts of the fasteners of non-rotational
parts.
- when using electric tools for production or
other purposes connected with making a prof-
it, as well as in case of malfunctions related
to instability of the power network parameters
exceeding the norms established by GOST;
- in the events of improper operation (use the
electric machine for other than intended pur-
poses, attachments to the electric machine of
attachments, accessories, etc. not provided
by the manufacturer);
- with mechanical damage to the case, pow-
er cord and in case of damages caused by
aggressive agents and high and low tempera-
tures, ingress of foreign objects in the ven-
tilation grids of the electric machine, as well
as in case of damage resulting from improper
storage (corrosion of metal parts);
- natural wear and tear on the parts of the
