BSD TKS-1300 User manual

OPERATION AND MAINTENANCE MANUAL
TKS-1300
TKS-1500
TKS-1500LS
TKS-2500LS
TKS-3500LS
TKS-4500LS
TKS-2500LSF
LOW VOLTAGE
METALASSEMBLY SCREWDRIVER
KILEWS INDUSTRIAL CO., LTD.
http://www.kilews.com
Y21003-5-001

1
Metal Assembly Screwdrivers are designed for installing threaded fasteners in light industrial and
appliance manufacturing applications.
KILEWS is not responsible for customer modification of tools for applications on which KILEWS was
not consulted.
Important safety information enclosed.
Read all these instructions before placing tool in service or operation this tool and save these instructions.
It is the responsibility of the employer to place the information in this manual into the hands of the
operator. Failure to observe the following warnings could result in injury. When using electric tools, Basic
safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury,
including the following:
WARNING
NOTICE

2
1.Important Safety Instructions
2.GroundingInstructions
3.OperationsCautions
4.Description of Operation
5.Servicing
6.Specifications
7.Accessories
8.Torque Adjustment Operation

3
1) Keep work area clean
Cluttered areas and benches invite injuries.
2) Consider work area environment
Do not expose power tools to rain. Do not use power tools in damp or wet locations. Keep work area
well lit. Do not use power tools where there is risk to cause fire or explosion.
3) Guard against electric shock
Avoid body contact with earthed or grounded surfaces (e.g. pipes, radiators, ranges, refrigerators).
4) Keep children away
Do not let visitors touch the tool or extension cord. All visitors should be kept away from work area.
5) Store idle tools
When not in use, tools should be stored in a dry, high or locked up place, out of reach of children.
6) Do not force the tool
It will do the job better and safer at the rate for which it was intended.
7) Use the right tool
Do not force small tools or attachments to do the job of a heavy duty tool. DO not use tools for
purposes not intended; for example, do not use circular saws to cut tree limbs or logs.
8) Dress properly
Do not wear loose clothing or jewellery, they can be caught in moving parts. Rubber gloves and
non-skid footwear are recommended when working outdoors. Wear protecting hair covering to
contain long hair.
9) Use safety glasses
Also use face or dust mask if the cutting operation is dusty.
10) Connect dust extraction equipment
If devices are provided for the connection of dust extraction and collection facilities ensure these are
connected and properly used.
11) Do not abuse the cord
Never carry the tool by the cord or yank it to disconnect it from the socket, Keep the cord away from
heat, oil and sharp edges.
12) Secure work
Use clamps or a vice to hold the work. It is safer than using your hand and frees both hands to
operate the tool.
13) Do not overreach
Keep proper footing and balance at all times.
14) Maintain tools with care
Keep cutting tools sharp and clean for better and safer performance. Follow instructions for
lubrication and changing accessories. Inspect tool cord periodically and if damaged have it repaired
by an authorized service facility. Inspect extension cords periodically and replace, if damaged. Keep
handles dry, clean and free from oil and grease.
15) Disconnect tools
When not in use, before servicing and when changing accessories such as blades, bits and cutters.
16) Remove adjusting keys and wrenches
Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before
turning it on.
17) Avoid unintentional starting
Do not carry a plugged-in tool with a finger on the switch. Ensure switch is off when plugging in.
18) Use outdoor extension leads
When tool is used outdoors, use only extension cords intended for outdoor use.
19) Stay alert
Watch what you are doing. Use common sense. Do not operate tool when you are tired.
1. Important Safety Instructions

4
20) Check damaged parts
Before further use of use the tool, a guard or other part is damaged should be carefully checked to
determine that it will operate properly and perform its intended function. Check for alignment of
moving parts, free running of moving parts, breakage of parts, mounting and any other conditions
that may affect its operation.A guard or other part that is damaged should be properly repaired or
replaced by an authorized service center unless otherwise indicated in this instruction manual. Have
defective switches replaced by an authorized service facility. Do not use the tool if the switch does
not turn it on and off.
21) Warning
The use of any accessory or attachment, other than those recommended in this instruction manual,
may present a risk of personal injury.
22) Have your tool repaired by a qualified person
This electric tool is in accordance with the relevant safety requirements. Repairs should only be
carried out by qualified persons using original spare parts, otherwise this may result in considerable
danger to the user.

5
WARNING！
DO NOT OPERATE THIS TOOLWITHOUT
PROTECTIVE EARTH CONNECTED
1. This tool should be grounded while in use to protect the operator from electric shock. NOTICE ! To
ensure the grounding result, the grounding conductor of the power cord must be well connected with
the grounding terminal of power facility. This tool is equipped with grounding conductors. The
Green(or Green and Yellow)conductor in the Power Cord is the grounding wire. Never connect Green
(or Green and Yellow) to a live terminal. The grounding wires in this tool can not only earth the
electric leakage safely, but also can eliminate ESD-the electrostatic that tool occurred while in use.
2. The grounding is the most important task a user. Periodically, depends on the working condition and
circumstance, for maintaining a good function the user has to check the grounding condition every
3~6 months by an electric meter and following simple steps; Set the Ohm meter to level R*100(Ohm).
Touching 2 test rods (“＋”＆”－”) together and reset the meter to “0”. Using the Red(“＋”) rod to
touch the Grounding wire on the Plug of controller’s cord, and the Black(“－”) rod to the end of Bit
Head. It stands for the grounding is normal if the meter is read as close as to “0”. For getting a
normal indication on the meter while in testing, need to press the test rods firmly to the testing
objects.
3. The instrument QC of the tool is performed before the tool ex-factory. The grounding continuity test
is conducted by input 26A voltage to the end of earth terminal, and subject to the resistance value
lower than 0.3Ohm.
2. Grounding Instructions

6
1) Whenever changing a bit, make certain the Forward / Reverse Switch is in the “OFF”position and
tool is unplugged.
2) Do not allow chemicals such as acetone, benzene, thinner, trichloroethylene ketene, or other similar
chemicals to come in contact with the screwdriver housing as damage will result.
3) Do not drop or abuse the screwdriver.
4) Do not adjust the torque setting higher than 8 on the torque scale.
5) There should be a tool rest interval when cycles three seconds or longer. This tool is intended for a
duty cycle of 0.8 sec on, 2.4 sec off.
6) Do not use this screwdriver for tightening wood screws. This is “ Metal Assembly Screw Driver ”.
7) Do not operate the Forward / Reverse Switch the motor is running.
8) Whenever a tool is not being used, move the Forward / Reverse Switch to the “OFF” position and
unplug the screwdriver.
● Do not drop or abuse the tool.
● Whenever a tool is not being used, position the Power Switch to the “OFF” position and unplug the
power cord.
3. Operations Cautions
CAUTION

7
Attaching / detaching bit and bit type
Push up the holder clamp by finger tip, and it will be unlocked. Thus, the bit can be freely attached and
detached (single finger notion type) select such a bit whose shank is equal to the size shown below.
insert the power plug into a receptacle and set the changeover switch to “F”position.
Apply the bit to the screw head and press the lever or push main body to, then the switch will be
turned ON to start the motor running.
When the screw is tighten and reach the torque that you had set, The tool will stopped
automatically.
To reset the tool by releasing the lever to the original position or releasing the bit From the screw
head.
To return the screw, set the changeover switch to “R”position.
Maintenance and Inspection:
1. The screw driver must be operated in top condition, one day working hour must be
not more than eight hours.
2. Periodically check for wear of motor 、Carbon brush, one day for eight hours use is normal, replace it
after every five to six months.
3. Please note don’t let the motor get over heated, every minute use 10~15 screws to operate.
4. The frequency use of this electric screw driver is over than eight hours a day, still it needs
periodically testing and treatment. Every 5-6 months.
5. Inspect tool cords periodically and if damaged, have them repaired by an authorized service facility.
Inspect extension cords periodically and replace if damaged.
6. Do not remove any labels. Replace any damaged label.
4. Description of Operation
5. Servicing

8
1. The use of other than genuine KILEWS replacement parts may Result in decreased
tool performance and increased maintenance, and may invalidate all warranties.
2. All repairs and maintenance of this tool and its word must be performed by an authorized service
center.
3. KILEWS is not responsible for customer modification of tools for applications on which KILEWS was
not consulted.
4. Repairs should by made only by authorized, trained personnel. Consult your nearest KILEWS
authorized service center.
5. It is the responsibility of the employer to place the information in this manual into the hands of the
operator.
DO NOTATTEMPT TO REPAIR THIS
ELECTRIC SCREW DRIVER
SAVE THESE INSTRUCTIONS
DO NOT DESTROY
CAUTION
CAUTION

9
MODEL(TKS-)
1300
1500
1500LS
2500LS
3500LS
4500LS
2500LSF
Input voltage(AC)
220VAC 50/60Hz
Rated input
48W
50W
Bit torque
Kgf.cm
0.5-7
2-15
2-15
5-25
10-35
15-45
5-18
Lbf.in
0.44-6.10
1.68-13.01
1.68-13.01
4.34-21.68
8.67-30.36
13.01-39.03
4.34-15.58
N.m
0.05-0.69
0.19-1.47
0.19-1.47
0.49-2.45
0.98-3.43
1.47-4.41
0.49-1.76
Torque Adjustment
Stepless
Unloaded Rotation Speed
(R.p.m) ±10%
1000
700
500
2000
Metal assembly
screw
Machine
screw(mm)
1.4-2.6
2.0-4.0
2.0-4.0
2.6-4.0
3.0-5.0
4.0-6.0
2.6-4.0
Tapping
screw(mm)
1.4-2.0
2.0-3.0
2.0-3.0
2.6-3.5
3.0-4.0
4.0-5.0
2.6-3.5
Weight (g)
480
600
Length (mm)
230
264
Model of Torque Fixing Ring
KC-3
KC-2
Model of Suspension Rack
KH-4(KC&KH-2)
KH-2(KC&KH-1)
Bit Type
Ø 4mm Ø 5mm
HEX 5mm HEX
6.35mm
* 1N.m=10.2Kgf.cm 1N.m=8.85Lbf.in
1. BIT Type ：No. 00 ．． Bit use in dia 1.3-1.8mm screw
No. 0．．．．Bit use in dia 1.6-2.0mm screw
No. 1．．．．Bit use in dia 2.0-2.6mm screw
No. 2．．．．Bit use in dia 3.0-4.0mm screw
TKS-1300 with BIT 1# & 2# 1 Pce. Each
TKS-1500 with BIT 1# & 2# 1 Pce. Each
TKS-1500LS with BIT 1# & 2# 1 Pce. Each
TKS-2500LS with BIT 1# & 2# 1 Pce. Each.
TKS-3500LS with BIT 2# 2 Pcs
TKS-4500LS with BIT 2# 2 Pcs.
TKS-2500LSF with BIT 1# & 2# 1 Pce. Each.
2.Suspension rack and Torque fixing ring acceptable for use with the tool are available from
KILEWS catalogue.
※Specifications
※Accessories

10
To adjust the torque on these screwdrivers. Proceed as follows :
1. Determine the torque output of the tool by checking a tightened Fastener with a torque wrench.
2. Increase or decrease the torque by rotating the Spring Adjusting Ring. Rotating the Ring clockwise to
a higher number on the torque Scale increase torque output while rotating the Ring counterclockwise
to a lower number decreases the torque output.
3. Check the adjustment with a torque wrench. A number of factors will affect torque output from one
job to another. Final torque adjustment should be made at the job through a of series of gradual
increase. Always start below the desired torque and work upward.
4. Adjust the bit torque by changing the driving in length of the adjust ring at the end.
5. The relationship between torque scale and bit torque is as shown Ring, in the torque diagram. The
figures of torque scale do not indicate bit torque values. However, the clamping torque of screw itself
is different form type, size, material of the screw and the material of its mating part. Use it as
standard to obtain an appropriate clamping torque.
6. The (Return torque method) in which once-clamped screw is returned with torque wrench or the like
is available as one of torque control methods however, note that the measured values by the return
torque method generally appear in 10%-30% lower than the actually clamping torque.
7. The torque checker measures the torque of screwdriver. The clamping torque of screw itself is
different from the clamped conditions. Understand the correlation between clamping torque values
and the torque checker values perform the torque control properly.
1. Also in reverse rotation, the clutch is turned off in such manner as in normal rotation, stopping the
motor running. Accordingly, when the screw tightened at a large torque, set it to a higher torque
scale.
2. The number from zero to eight on the Torque Scale are reference number only and not an indication
of actual torque output.
CAUTION
※Torque Adjustment Operation

2937
3034
32
31
33
36
55
38
39
4041424344
454647
48
28
27
222322
26
25
24
26
9
16
17
49
12
13
14
15
CUSTOMER
ITEM NO:
TITLE:
DWG NAME
MATERIAL
DES. BY
CHKD.BY
APPD.BY
SHRINK
DATE
DATE
DATE
PRODUCTION NO.
THIRD ANGLE PROJECTION.
UNITSCALESHT NO.
OF SHTS.
11
52
3132
51
50
8
10
53
35
MODEL:
TKS-1500LA.B.C.AD
TKS-1300LA.B.C.AD
DWG NO:

No PARTS NO PARTS NAME-E Q'ty No PARTS NO PARTS NAME-E Q'ty
1 AB30001-1 CORD 1 GZ22141-2A CLUTCH ASSY 1500LA 1
2 AD30001-4 CORD American 1 GZ22141-2B CLUTCH ASSY 1500LB 1
AD30001-2Y CORD Chinese 1 GZ22141-2C CLUTCH ASSY 1500LC 1
AD30001-5 CORD Europe 1 GZ22141-2AD CLUTCH ASSY 1500LAD 1
AD30001-1G CORD UK 1 29 GK20231 “C” RING 1
AD30001-1I CORD India 1 30 GI20251-1 IRON WASHER 1
3 AA30007 CORD 1Ft 1 31 GH20241 GEAR PLANET 8
AA30007-1 CORD American 1Ft 1 32 GG20271 GEAR SEAT 2
AA30007-3 CORD Chinese 1Ft 1 33 G20101 GEAR OF CENTER 1
AA30007-2 CORD Europe 1Ft 1 34 GA30311-5 GEAR CASE 1
AA30007-5 CORD UK 1Ft 1 35 GN30321 MAIN BEARING 1
AA30007-5E CORD India 1Ft 1 36 GC20301 CAM 1
4 EC30006 EMC-BOX CASE ONLY 1 37 GP30351 STEEL BALL-4MM 2
5 CH90152-1F SCREW 2 38 GD30381A SHAFT A-TYPE 1
6 AA30008-1 CORD 9FT 1 GD20321-3 SHAFT B-TYPE 1
AA30009-8 CORD 9FT 1 GD20321-2 SHAFT C-TYPE 1
7 EG30005-4F PCB 1 GD20321 SHAFT AD-TYPE 1
8 CB22021-2 HOUSING UNDERSIDE FOR 220V 1 39 GP20331 STEEL BALLS FOR "A&AD" TYPE 2
9 CA22101-2 HOUSING UPSIDE FOR 220V 1 GP21291B STEEL BALLS FOR "B&C" TYPE 2
10 CJ20011 SUSPENSION RING 1 40 GF20341 WARRING PLATE FOR A,C,AD TYPE 1
11 CC20031-5 TRIGGER 1 GF20341B WARRING PLATE FOR B TYPE 1
12 E31203-1 BIRDGE DIODE 1 41 GE20351-1 WARRING SPRING FOR 1300L 1
13 HB50072 START SWITCH 1 GE20351 WARRING SPRING FOR 1500L 1
14 HA15091F CHANGEOVER SWITCH 1 42 GY30421 WARRING SPRING BASE FOR A,C,AD 1
15 CI30211 SWITCH CAP FOR 1300L 1 GY30421B WARRING SPRING BASE FOR B TYPE 1
CI30212 SWITCH CAP FOR 1500L 1 43 GK20231B C-RING FOR B TYPE 1
16 CH20102 SCREW 3 44 GB30441-10 CLUTCH CASE FOR A,C,AD TYPE 1
17 MO15121-2 MOTOR ASSEMBLY 220V 1 GB30441-7A CLUTCH CASE FOR B TYPE 1
18 EB33610-2 CERAMICS CAPACITOR 1 45 GO30452 BIT SPRING FOR A,C,AD TYPE 1
19 MD20151 BRUSH CAP 2 GO20391B-J BIT SPRING FOR B TYPE 1
20 MC20161 BRUSH 2 46 GJ30461 BIT SLEEVE FOR A,C,AD TYPE 1
21 ML33571 MOTOR TOP COVER 220V 1 GJ3046B BIT SLEEVE FOR B TYPE 1
22 ME21481 ARMATURE BEARING 220V 2 47 GQ30471 “C” RING FOR A,C,AD TYPE 1
23 MH23601 ARMATURE FOR 1300L 1500L 1 GQ21361 “C” RING FOR B TYPE 1
24 MJ33631 MOTOR YORK ASSEMBLY FOR 1300L 1500L 1 48 GL30481-5 TORQUE ADJ PINS 4
25 MB33651A MOTOR END COVER 220V 1 49 GM20431-1 TORQUE ADJ RING 1
26 MA33621B ASSEMBLY SPRING 220V 2 50 GS30501 “C” RING FOR GM21381 1
27 MK33091 FAN 220V 1 51 CD20111 COUPLER 1
28 GZ22141-1A CLUTCH ASSY 1300LA 1 52 MF30101 INSULATING WASHER 1
GZ22141-1B CLUTCH ASSY 1300LB 1 53 P12104 8cm RETAINING CLIP 1
GZ22141-1C CLUTCH ASSY 1300LC 1 54 EJ30002-3 CE Box Ass'y-220V 1
GZ22141-1AD CLUTCH ASSY 1300LAD 1 55 GN30435 MAIN BEARING 1
TKS-1300LA.B.C.AD TKS-1500LA.B.C.AD

2937
3034
3136
38
39
40414243
444546
47
28
27
222322
26
25
24
26
9
16
17
48
12
13
14
15
CUSTOMER
ITEM NO:
TITLE:
DWG NAME
MATERIAL
DES. BY
CHKD.BY
APPD.BY
SHRINK
DATE
DATE
DATE
PRODUCTION NO.
THIRD ANGLE PROJECTION.
UNITSCALESHT NO.
OF SHTS.
11
51
3132
50
49
8
10
52
35
33
MODEL:
TKS-1500LD
TKS-1300LD
54
DWG NO:

No PARTS NO PARTS NAME-E Q'ty No PARTS NO PARTS NAME-E Q'ty
1 AB30001-1 CORD 1 24 MJ33631 MOTOR YORK ASSEMBLY 1
2 AD30001-4 CORD American 1 25 MB33651A MOTOR END COVER 220V 1
AD30001-2Y CORD Chinese 1 26 MA33621B ASSEMBLY SPRING 220V 2
AD30001-5 CORD Europe 1 27 MK33091 FAN 220V 1
AD30001-1G CORD UK 1 28 GZ22141-1D CLUTCH ASSY 1300LD 1
AD30001-1I CORD India 1 GZ22141-2D CLUTCH ASSY 1500LD 1
3 AA30007 CORD 1Ft 1 29 GK20231 “C” RING 1
AA30007-1 CORD American 1Ft 1 30 GI20251-1 IRON WASHER 1
AA30007-3 CORD Chinese 1Ft 1 31 GH20241 GEAR PLANET 8
AA30007-2 CORD Europe 1Ft 1 32 GG20271 GEAR SEAT 1
AA30007-5 CORD UK 1Ft 1 33 GG20261 GEAR SEAT 1
AA30007-5E CORD India 1Ft 1 34 GA30311-5 GEAR CASE 1
4 EC30006 EMC-BOX CASE ONLY 1 35 GN30321 MAIN BEARING 1
5 CH90152-1F SCREW 2 36 GC20301 CAM 1
6 AA30008-1 CORD 9FT 1 37 GP30351 STEEL BALL-4MM 2
AA30009-8 CORD 9FT 1 38 GD20321-1 SHAFT D-TYPE 1
7 EG30005-4F PCB 1 39 GP20331 STEEL BALLS FOR "D" TYPE 2
8 CB22021-2 HOUSING UNDERSIDE FOR 220V 1 40 GF20341 WARRING PLATE FOR D TYPE 1
9 CA22101-2 HOUSING UPSIDE FOR 220V 1 41 GE20351-1 WARRING SPRING FOR 1300LD 1
10 CJ20011 SUSPENSION RING 1 GE20351 WARRING SPRING FOR 1500LD 1
11 CC20031-5 TRIGGER 1 42 GY30421 WARRING SPRING BASE FOR D 1
12 E31203-1 BIRDGE DIODE 1 43 GB30441-10 CLUTCH CASE FOR D TYPE 1
13 HB50072 START SWITCH 1 44 GO30452 BIT SPRING FOR D TYPE 1
14 HA15091F CHANGEOVER SWITCH 1 45 GJ30461 BIT SLEEVE FOR D TYPE 1
15 CI30211 SWITCH CAP FOR 1300LD 1 46 GQ30471 “C” RING FOR D TYPE 1
CI30212 SWITCH CAP FOR 1500LD 1 47 GL30481-5 TORQUE ADJ PINS 4
16 CH20102 SCREW 3 48 GM20431-1 TORQUE ADJ RING 1
17 MO15121-2 MOTOR ASSEMBLY 220V 1 49 GS30501 “C” RING FOR GM21381 1
18 EB33610-2 CERAMICS CAPACITOR 1 50 CD20111 COUPLER 1
19 MD20151 BRUSH CAP 2 51 MF30101 INSULATING WASHER 1
20 MC20161 BRUSH 2 52 P12104 8cm RETAINING CLIP 1
21 ML33571 MOTOR TOP COVER 220V 1 53 EJ30002-3 CE Box Ass'y-220V 1
22 ME21481 ARMATURE BEARING 220V 2 54 GN30435 MAIN BEARING 1
23 MH23601 ARMATURE FOR 1300LD 1500LD 1
TKS-1300LD TKS-1500LD

4
MODEL:
TKS-1500LS
TKS-2500LS
TKS-3500LS
TKS-4500LS

No. Parts No. Parts Name-E Q’ty No. Parts No. Parts Name-E Q’ty
1 AD30001-4 CORD American 1 31 GK21181 “C” ring for GI21191 1
AD30001-2Y CORD Chinese 1 32 GI21191 Iron Washer 1
AD30001-5 CORD Europe 1 33 GH92231 Gear Planet-4500LS 4
AD30001-1G CORD UK 1 GH91232 Gear Planet-3500LS 3
AD30001-1I CORD India 1 GH20241 Gear Planet 1500LS & 2500LS 3
2 AA30007-1 CORD American 1Ft 1 34 GG92241-1 Gear Seat-4500LS 1
AA30007-3 CORD Chinese 1Ft 1 GG91242-1 Gear Seat-3500LS 1
AA30007-2 CORD Europe 1Ft 1 GG21231-2 Gear Seat-1500LS & 2500LS 1
AA30007-5 CORD UK 1Ft 1 35 GG92271-1 Gear Seat-4500LS 1
AA30007-5E CORD India 1Ft 1 GG91272-1 Gear Seat-3500LS 1
3 EJ30002-3 CE Box Ass’y 1 GG21231-2 Gear Seat-1500LS & 2500LS 1
4 EG30005-4 PCB,CE SemiAuto 1 36 GA35241-1 Gear Case-4500LS & 3500LS 1
5 EC30006 EMC-BOX CASE ONLY 1 GA21241-1 Gear Case-1500LS & 2500LS 1
6 CH90152-1F SCREW 2 37 GN21251 Main Bearing 1
7 AA30009-8 CORD 9FT 1 38 GW21531 Iron Ring 1
8 CB25041-2 Houing Underside 1 39 GC31321 Cam 1
9 CA25161-2 Houing Upside 1 40 GP30351 Steel Ball-4mm 2
10 CJ20011 Suspension Ring 1 41 GD21281A Shaft-5mm Hex 1
11 CC21011-4 Trigger 1 GD21281B Shaft-6.35mm Hex 1
12 CK28031-1 Trigger Spring 1 42 GP21291A Steel Ball-3mm 2
13 E31203-1 Birdge Diode 1 GP21291B Steel Ball-2.5mm 2
14 HB50072 Start Switch 1 43 GF21301 Warring Plate 1
15 CH30003F Screw 4 44 GE92382 Warring Spring-4500LS 1
16 HA92051F ChangeOver Switch-4500LS 1 GE35311 Warring Spring-3500LS 1
HA91042F ChangeOver Switch-3500LS 1 GE21311 Warring Spring-2500LS 1
HA91041F ChangeOver Switch-1500LS & 2500LS 1 GE20351-2 Warring Spring-1500LS 1
17 CH20102 Screw 3 45 GY21321 Warring Spring Base 1
18 MO22091-3 Motor Assembly-4500LS 1 46 GR20801 Copper Ring 1
MO22091-2 Motor Assembly-3500LS 1 47 G20202 Clutch Case 1
MO22091-1 Motor Assembly-1500LS & 2500LS 1 48 GO21341 Bit Spring 1
19 EB33610-2 CERAMICS CAPACITOR 1 49 GJ21351 Bit Sleeve 1
20 EA21431 Capacitor 1 50 GQ21361 “C” ring for GJ21351 1
21 MD91531-1 Brush Cap 2 51 GL21371 Torque Adj Pins 4
22 MC20161 Brush 2 52 GM21381 Torque Adj Ring 1
23 M10303-1 Motor Top Cover 1 53 GS21391 “C” ring for GM21381 1
24 ME21481 Armature Bearing 2 54 CD21031 Coupler 1
25 MH22471 Armature 1 55 CH30681 GROUNDING MEANS 1
26 MJ90601 Motor York Assembly 1 56 MF90061 Insulating Washer 1
27 MB21521A Motor End Cover 1 57 G20102 Gear Seat-2500LS 1
28 MA21491B Assembly Spring 2 58 ML22421-1 Motor Top Cover Assembly 1
29 MK92091 Fan-4500LS 1 59 GN30442 Main Bearing 1
MK91091 Fan-3500LS 1 60 GB21331 Clutch Case Assembly 1
MK21111 Fan-1500LS 2500LS 1 61 P12104 8cm RETAINING CLIP 1
30 GZ21541-2A(B) Clutch Assy-4500LSA(B) 1 62 GH92231-1 Gear Planet-4500LS 4
GZ21135-2A(B) Clutch Assy-3500LSA(B) 1 GH91232-1 Gear Planet-3500LS 3
GZ21125-2A(B) Clutch Assy-2500LSA(B) 1 GH20241 Gear Planet 1500LS & 2500LS 3
GZ21115-2A(B) Clutch Assy-1500LSA(B) 1
TKS-1500LS TKS-2500LS TKS-3500LS TKS-4500LS

MODEL:
4
TKS-2500LSF

No. Parts No. Parts Name-E Q’ty No. Parts No. Parts Name-E Q’ty
1 AD30001-4 CORD American 1 28 MA21491B Assembly Spring 2
AD30001-2Y CORD Chinese 1 29 MK21111PF Fan-2500LSF 1
AD30001-5 CORD Europe 1 30 GZ21125-2AF(BF) Clutch Assy-2500LSFA(B) 1
AD30001-1G CORD UK 1 31 GK21181 “C” ring for GI21191 1
AD30001-1I CORD India 1 32 GI21191 Iron Washer 1
2 AA30007-1 CORD American 1Ft 1 33 G21301 WASHER,HIGH SPEED 1
AA30007-3 CORD Chinese 1Ft 1 34 GH21221-1 Gear Planet -2500LSF 3
AA30007-2 CORD Europe 1Ft 1 35 GG21231-1 Gear Seat-2500LSF 1
AA30007-5 CORD UK 1Ft 1 36 GA21241-1 Gear Case 1
AA30007-5E CORD India 1Ft 1 37 GN21251 Main Bearing 1
3 EJ30002-3 CE Box Ass’y 1 38 GW21531 Iron Ring 1
4 EG30005-4 PCB,CE SemiAuto 1 39 GC31321 Cam 1
5 EC30006 EMC-BOX CASE ONLY 1 40 GP30351 Steel Ball-4mm 2
6 CH90152-1F SCREW 2 41 GD21281A Shaft-5mm Hex 1
7 AA30009-8 CORD 9FT 1 GD21281B Shaft-6.35mm Hex 1
8 CB25041-2 Houing Underside 1 42 GP21291A Steel Ball-3mm 2
9 CA25161-2 Houing Upside 1 GP21291B Steel Ball-2.5mm 2
10 CJ20011 Suspension Ring 1 43 GF21301 Warring Plate 1
11 CC21011-4 Trigger 1 44 GE21312 Warring Spring-2500LSF 1
12 CK28031-1 Trigger Spring 1 45 GY21321 Warring Spring Base 1
13 E31203-1 Birdge Diode 1 46 GR20801 Copper Ring 1
14 HB50072 Start Switch 1 47 G20202 Clutch Case 1
15 CH30003F Screw 2 48 GO21341 Bit Spring 1
16 HA91041F ChangeOver Switch-2500LSF 1 49 GJ21351 Bit Sleeve 1
17 CH20102 Screw 3 50 GQ21361 “C” ring for GJ21351 1
18 MO22091-1F Motor Assembly 1 51 GL21371 Torque Adj Pins 4
19 EB33610-2 CERAMICS CAPACITOR 1 52 GM21381 Torque Adj Ring 1
20 EA21431 Capacitor 1 53 GS21391 “C” ring for GM21381 1
21 MD91531-1 Brush Cap 2 54 CD21031 Coupler 1
22 MC20161 Brush 2 55 CH30681 GROUNDING MEANS 1
23 M10303-1 Motor Top Cover 1 56 MF90061 Insulating Washer 1
24 ME21481 Armature Bearing 2 57 ML22421-1 Motor Top Cover Assembly 1
25 MH22471 Armature 1 58 GN30442 Main Bearing 1
26 MJ90601 Motor York Assembly 1 59 GB21331 Clutch Case Assembly 1
27 MB21521A Motor End Cover 1 60 P12104 8cm RETAINING CLIP 1
TKS-2500LSF