PAA MAMBO User manual

OWNERS MANUAL
Congratulations on the purchase of your bathtub!
MAMBO
Please read and follow all the instructions contained in this Owners Manual before installing your bath-
tub. In addition, you should refer to these instructions during the life of your bathtub.
Instruction for bathtub installation
Only a qualified service an should perfor the installation of your bathtub.
Preparation of area
As the front panel of the tub ust be freely oved either during the installation or exploitation, choose the right area
in which to install the bathtub.
Prepare the floor and walls before installation works. The corner in which the tub will be installed, as well as the
walls ust be in straight angle against to floor to avoid possible gaps between tub and wall.
The place under the tub ust be in the sa e level as the floor.
All drain connections should fit in between bathtub and its legs (see the drawing).
The centre of drain is pointed in the drawing. Before asse bling connections check the inlet of drainage (Ø 50 );
it ust be either in the sa e level or axi u 50 fro the floor and not closer within a radius of 200 fro
the centre of bathtubs drain outlet (see the drawing).
In case the ixers are installed on the edge of the tub outlet pipes for hot and cold water with the ½” treads ust be
arranged under the unit.
All the odels of PAA tubs and whirlpools could be installed in built-in version without front panel. For built-in ver-
sion plan and provide access door for reaching the ost significant assage syste parts (water pu p and air
blower). Please consult with PAA or its dealers in these cases.
Also provide the necessary space around the water pu p and blower to properly ventilate and cool the during
operation. For built-in tub there is necessary to plan ventilation access door as well.
Electrical connection of the whirlpools
Grounding is required. Connect the tub to 230V, 50Hz wiring connection. Provide to each syste proper electric
power, choose the right crosscut cable. Use for syste separate 16A differential safety catch (electric current loss
ax. 30 A). Advised length for cable is 150 c .
Upon receipt, i ediately inspect the bathtub to ake sure the unit has shipped as ordered and
has arrived unda aged. If a proble is discovered, call your PAA dealer i ediately.
Handling da ages are not covered under warranty.
max 20mm
pic. a
C
D
position C2
pic. b
C1
C2

Installation of bathtub
When place for tub is prepared, water and drainage asse bled, bathtub is ready for installation.
Fix the longest bathtub side to the wall.
The distance between front panel and the floor has to be less than 20
Adjust the height of the tub using unit feet (drawing a); loosen the nut C, adjust the right height of the feet D. Fix
the feet D and fasten the nut C.
Installation of bathtub panels
Use springs and angles for panels’ fixation to the tub (drawing b). Front panel has to be set first.
The lower edge of the panel fasten with springs (position C2) to the fra e and upper edge put between angles
and tub’s body (position C1).
Instruction for bathtub and whirlpool using
Clean the tub after using with soft cloth, in case of necessity use sanitary cleaning liquid (such as Cillit, Ajax).
Avoid abrasive, acid and alkaline cleaners!
Avoid the contact with hot objects (such as cigarettes, hairdryer, all kind of candles and others with te perature
ore than +85oC) and open fla e with the bathtub’s surface.
Avoid durable contact of the following substances with the tub’s surface:
Silicone oils, spirits (over 30%), all-purpose adhesives, sprayers, inapplicable sanitary cleaners and disinfectants,
hydrogen peroxide, pesticides dissolved in water, derv, acrylic paints and varnishes, acetic acid up to 25%,
other active che ical substances.
Exclude the tub’s surface contact with the following substances:
Sealing co pounds on acrylic and polyurethane base, ca phor, nail varnish and re over of nail varnish,
foa plastic, PVC and rubber in plastic condition, concentrated ethyl alcohol, stain re overs, iodine tincture,
gasoline, solvents, nitrocellulose varnish, concentrated acetic acid, acetone, liquid a onia, chlorine, ether
high acids.
For ore detailed infor ation contact anufacturer PAA.
Avoid echanical da ages of unit – hard i pacts and scratches.
Do cleaning of assage syste pipes with professional liquids not less than once in 2-3 onths.
First fill up the tub with the cold water and only then with hot one.
In case water ixer is leaking or da aged, fix or change it i ediately.
Warranties
All PAA products are provided 2 years warranty.
Warranty for PAA bathtubs’ surface is 5 years.
All assage tubs, installed by PAA certified specialists, are provided 3 years warranty.
Warrant requirements
The warranty shall not apply to:
da age caused by incorrect transportation or inadequate packing during ship ent
da age caused by failure to adhere to any of the operating, installation or aintenance instructions stated in
our anual
any incorrect operating procedures in bathtub or whirlpool, breakage or da ages caused by the fault, care-
lessness, isuse, i proper aintenance, abuse or odification of the product, as well as any che ical or
natural corrosion, fire or any other causality
da ages caused by using in conditions which the bathtub is not provided for.
PAA reserves the right to discontinue or change odels, colours and design specifications without
prior notice and without incurring of any obligations.