Pac-Dent PACENDO iRoot Pro Plus Manual

Quick Start Guide | Installation & Setup
Align locating pins of contra-angle with
the positioning slots on the motor and
push the contra-angle horizontally. A
“click” will indicate the installation is in
place
User-defined system in rotation:
Touch SYSTEM (1) to select program
(2). Touch FILE (3) to select file 1. Set
up speed, torque, and auto-reverse
mode using the equivalent SPEED,
TORQUE, and Auto-Rev buttons.
User-defined system in reciprocation:
Touch SYSTEM (1) to select
reciprocating (2). Touch FILE (3) to
select file 1. Set up speed and torque,
using the equivalent SPEED, TORQUE
buttons. Touch SET (4) to switch
between forward & reverse (5). Touch
ANGLE (6) to set up angles.
For Autosense:
Touch SYSTEM (1) to select Autosense
(2). Use the Preferred Files in
sequence. Sensitivity to turn
rotary>>reciprocation>>rotary can be
selected by touching TORQUE button
up or down (3).
Touch and hold SET (1) to set up
sub-settings. Touch ANGLE (2) to
determine the apical position alarm (3).
Position 00 (foramen exit) is
recommended.
Touch and hold SET (1) to set up
sub-settings. Touch SPEED to select
(2) apical reverse/apical stop; auto
start and apical slow down (3).
To activate/deactivate any of the
selections press En-Ap (4).
Place the handpiece at the base
handpiece slot. Insert power cable on
power socket at right lateral of the
base (1). Once cable is connected to
base a battery icon will appear (2)
showing status of battery. A blinking
light indicates that the battery is being
charged.
Touch and hold power (1) for 3
seconds. Display will show the last
working mode chosen. To change the
operation mode press En-Ap (2). Motor
and apex locator combined mode (3) is
preferred. Press on/off button on the
handpiece to enter ready-on.
Touch SYSTEM (1) to select Preferred
File System (2).
Press Auto Rev (1) to set up the
preferred auto reverse mode.
2- Auto reverse on
3- Auto stop on
4- Auto reverse/auto stop off (4).
Auto-reverse on is recommended
Quick Start Guide | Installation & Setup
Align locating pins of contra-angle with
the positioning slots on th motor and
push the contra-angle horizontally. a
“click” will indicate the installation is in
place
User-defined system in rotation:
Touch SYSTEM (1) to select program
(2). Touch FILE (3) to select file 1. Set
up speed, torque, and ato-reverse
mode using the equivalent SPEED,
TORQUE, and Auto-Rev buttons.
User-defined system in reciprocation:
Touch SYSTEM (1) to select
reciprocating (2). Touch FILE (3) to
select file 1. Set up speed and torque,
using the equivalent SPEED, TORQUE
buttons. touch SET (4) to switch
between forward & reverse (5). Touch
ANGLE (6) to set up angles.
For Autosense:
Touch SYSTEM (1) to select Autosense
(2). Use the Preferred Files in
sequence. Sensitivity to turn
rotary>>reciprocation>>rotary can be
selected by touching TORQUE button
up or down (3).
Touch and hold SET (1) to set up
sub-settings. Touch ANGLE (2) to
determine the apical position alarm (3).
Position 00 (foreamen exit) is
recommended.
Touch and hold SET (1) to set up
sub-settings. Touch SPEED to select
(2) apical reverse/apical stop; auto
start and apical slow down (3).
To activate/deactivate any of the
selections press En-Ap (4).
Place the handpiece at the base
handpiece slot. Insert power cable on
power socket at right lateral of the
base (1). Once cable is connected to
base a battery icon will appear (2)
showing status of battery. A blinking
light indicates that the battery is being
charged.
Touch and hold power (1) for 3
seconds. Display will show the last
working mode chosen. To change the
operation mode press En-Ap (2). Motor
and apex locator combined mode (3) is
preferred. Press on/off button on the
handpiece to enter ready-on.
Touch SYSTEM (1) to selet Preferred
File System (2).
Press Auto Rev (1) to set up the
preferred auto reverse mode.
2- Auto reverse on
3- Auto stop on
4- Auto reverse/auto stop off (4).
Auto-reverse on is recommended
For More Information:
Quick Start Guide| Installation &Setup
Align locating pins of contra-angle with
the positioning slots on the motor and
push the contra-angle horizontally. A
“click” will indicate the installation is in
place.
User-defined system in rotation:
Touch SYSTEM (1) to select program
(2). Touch FILE (3) to select file . Set
up speed, torque, and auto-reverse
mode using the equivalent SPEED,
TORQUE, and Auto-Rev buttons.
User-defined system in reciprocation:
Touch SYSTEM (1) to select
reciprocating (2). Touch FILE (3) to
select file. 1. Set up speed and torque,
using the equivalent SPEED, TORQUE
buttons. Touch SET (4) to switch
between forward & reverse (5). Touch
ANGLE (6) to set up angles.
For AutoSense:
Touch SYSTEM (1) to select
AutoSense . Use the SUHIHUUHGILOHV in
sequence. Sensitivity to turn
rotary>>reciprocation>>rotary can be
selected by touching TORQUE button
up or down (2).
Touch and hold SET (1) to set up
sub-settings. Touch ANGLE (2) to
determine the apical position alarm (3).
Position 00 (foreamen exit) is
recommended.
Touch and hold SET (1) to set up
sub-settings. Touch SPEED to select
(2) apical reverse/apical stop; auto
start and apical slow down (3).
To activate/deactivate any of the
selections press En-Ap (4).
Place the handpiece at the base
handpiece slot. Insert power cable on
power socket at right lateral of the
base(1). Once cable is connected to
base a battery icon will appear(2)
showing status of battery. A blinking
light (3) indicates that the battery is
being charged.
Touch and hold power(1) for 3
seconds. Display will show the last
working mode chosen. To change the
operation mode press En-Ap(2).Motor
and apex locator combined mode(3)is
preferred. Press on/off button on the
handpiece to enter ready-on.
Touch SYSTEM (1) to select
SUHIHUHGILOHVV\VWHP (2).
Press Auto Rev(1)to set up the
preferred auto reverse mode.
2- Auto-reverse on
3- Auto stop on
4- Auto-reverse/auto stop off .
Auto-reverse on is recommended
iPlus
PAC
ENDO
909.839.0888
[email protected]
670 Endeavor Circle, Brea, CA 92821
www.pac-dent.com
Rev.031821#06INTRPCL02A
For More Information:
Quick Start Guide| Installation &Setup
Align locating pins of contra-angle with
the positioning slots on the motor and
push the contra-angle horizontally. A
“click” will indicate the installation is in
place.
User-defined system in rotation:
Touch SYSTEM (1) to select program
(2). Touch FILE (3) to select file . Set
up speed, torque, and auto-reverse
mode using the equivalent SPEED,
TORQUE, and Auto-Rev buttons.
User-defined system in reciprocation:
Touch SYSTEM (1) to select
reciprocating (2). Touch FILE (3) to
select file. 1. Set up speed and torque,
using the equivalent SPEED, TORQUE
buttons. Touch SET (4) to switch
between forward & reverse (5). Touch
ANGLE (6) to set up angles.
For AutoSense:
Touch SYSTEM (1) to select
AutoSense . Use the SUHIHUUHGILOHV in
sequence. Sensitivity to turn
rotary>>reciprocation>>rotary can be
selected by touching TORQUE button
up or down (2).
Touch and hold SET (1) to set up
sub-settings. Touch ANGLE (2) to
determine the apical position alarm (3).
Position 00 (foreamen exit) is
recommended.
Touch and hold SET (1) to set up
sub-settings. Touch SPEED to select
(2) apical reverse/apical stop; auto
start and apical slow down (3).
To activate/deactivate any of the
selections press En-Ap (4).
Place the handpiece at the base
handpiece slot. Insert power cable on
power socket at right lateral of the
base(1). Once cable is connected to
base a battery icon will appear(2)
showing status of battery. A blinking
light (3) indicates that the battery is
being charged.
Touch and hold power(1) for 3
seconds. Display will show the last
working mode chosen. To change the
operation mode press En-Ap(2).Motor
and apex locator combined mode(3)is
preferred. Press on/off button on the
handpiece to enter ready-on.
Touch SYSTEM (1) to select
SUHIHUHGILOHVV\VWHP (2).
Press Auto Rev(1)to set up the
preferred auto reverse mode.
2- Auto-reverse on
3- Auto stop on
4- Auto-reverse/auto stop off .
Auto-reverse on is recommended
iPlus
PACENDO
909.839.0888
[email protected]
670 Endeavor Circle, Brea, CA 92821
www.pac-dent.com
Rev.031821#06INTRPCL02A
CX-C1
PAC-TAPER
CX-C1
PAC-TAPER
CX-C1
PAC-TAPER
CX-C1
PAC-TAPER
1
1
2
2
22
3
4
33
1 1
11
3
4 1 14
3
6 2
1
2 2
2
2
5
2
3
For More Information:
Quick Start Guide| Installation & Setup
Align locating pins of contra-angle with
the positioning slots on the motor and
push the contra-angle horizontally. A
“click” will indicate the installation is in
place.
User-defined system in rotation:
Touch SYSTEM (1) to select program
(2). Touch FILE (3) to select file . Set
up speed, torque, and auto-reverse
mode using the equivalent SPEED,
TORQUE, and Auto-Rev buttons.
User-defined system in reciprocation:
Touch SYSTEM (1) to select
reciprocating (2). Touch FILE (3) to
select file. 1. Set up speed and torque,
using the equivalent SPEED, TORQUE
buttons. Touch SET (4) to switch
between forward & reverse (5). Touch
ANGLE (6) to set up angles.
For AutoSense:
Touch SYSTEM (1) to select
AutoSense . Use the preferred les in
sequence. Sensitivity to turn
rotary>>reciprocation>>rotary can be
selected by touching TORQUE button
up or down (2).
Touch and hold SET (1) to set up
sub-settings. Touch ANGLE (2) to
determine the apical position alarm (3).
Position 00 (foreamen exit) is
recommended.
Touch and hold SET (1) to set up
sub-settings. Touch SPEED to select
(2) apical reverse/apical stop; auto
start and apical slow down (3).
To activate/deactivate any of the
selections press En-Ap (4).
Place the handpiece at the base
handpiece slot. Insert power cable on
power socket at right lateral of the
base(1). Once cable is connected to
base a battery icon will appear(2)
showing status of battery. A blinking
light (3) indicates that the battery is
being charged.
Touch and hold power(1) for 3
seconds. Display will show the last
working mode chosen. To change the
operation mode press En-Ap(2).Motor
and apex locator combined mode(3)is
preferred. Press on/off button on the
handpiece to enter ready-on.
Touch SYSTEM (1) to select
prefered le's system (2).
Press Auto Rev(1)to set up the
preferred auto reverse mode.
2- Auto-reverse on
3- Auto stop on
4- Auto-reverse/auto stop off .
Auto-reverse on is recommended
iPlus
PAC ENDO

EJBKĤL=?@AJP?KI
"J@A=RKN EN?HANA= 
SSSL=?@AJP?KI
-2864'06IZ
CX-C1
PAC-TAPER
CX-C1
PAC-TAPER
CX-C1
PAC-TAPER
CX-C1
PAC-TAPER
1
1
2
2
22
3
4
33
1 1
11
3
4 1 14
3
6 2
1
2 2
2
2
5
2
3

Quick Start Guide | Clinical Operation & Tests
Te s ts
Insert lip hook to female white socket
(1). insert measuring wire plug into
base socket. Insert USB measuring
cable’s large male plug into base
USB’s socket (2). Insert USB
measuring cable’s small male plug
into handpiece socket (3).
Ensure lip hook is in position.
Connect file clip to the gray female
socket. Place a K-File of proper
diameter inside canal up to temporary
W.L. Connect file clip to file. File icon
inside tooth canal image (1) will
appear.
Advance file. As instrument
progresses toward foramen, color
instruction bars accompanied by
audio signals will indicate file’s
progress. Stop file apical movement
when the instructions bars reach
“00” [foramen exit position](3).
Disconnect file clip. Leave lip hook in
position. Touch system down to
select The Preferred System. Place
Preferred Files 25 .04 in
contra-angle. Insert 25 .04 file inside
canal. As file approaches W.L.,
Display will show file progress.
Place rubber dam isolation prior to
endodontic treatment. Place the lip
hook onto patient’s lip.
C.S. (Curvature Sweetener) is the
first file to be used up to temporary
W.L. Preflare the canal. Use copious
irrigation.
Pull out measuring wire and turn base
off by touching power for 3 seconds.
Insert tester on the same slot of
measurement wire. Turn base on.
Display will show 01, 02, 03, or 04.
All results means working properly.
Grab the lip hook with the bent wire of
the file clip.
All instruction bars will be displayed
alongside a “-3” and a repeated beep
sound alarm.
Select the file system to be used by
touching SYSTEM up or down. Select
Preferred File System.
Quick Start Guide | Installation & Setup
Align locating pins of contra-angle with
the positioning slots on th motor and
push the contra-angle horizontally. a
“click” will indicate the installation is in
place
User-defined system in rotation:
Touch SYSTEM (1) to select program
(2). Touch FILE (3) to select file 1. Set
up speed, torque, and ato-reverse
mode using the equivalent SPEED,
TORQUE, and Auto-Rev buttons.
User-defined system in reciprocation:
Touch SYSTEM (1) to select
reciprocating (2). Touch FILE (3) to
select file 1. Set up speed and torque,
using the equivalent SPEED, TORQUE
buttons. touch SET (4) to switch
between forward & reverse (5). Touch
ANGLE (6) to set up angles.
For Autosense:
Touch SYSTEM (1) to select Autosense
(2). Use the Preferred Files in
sequence. Sensitivity to turn
rotary>>reciprocation>>rotary can be
selected by touching TORQUE button
up or down (3).
Touch and hold SET (1) to set up
sub-settings. Touch ANGLE (2) to
determine the apical position alarm (3).
Position 00 (foreamen exit) is
recommended.
Touch and hold SET (1) to set up
sub-settings. Touch SPEED to select
(2) apical reverse/apical stop; auto
start and apical slow down (3).
To activate/deactivate any of the
selections press En-Ap (4).
Place the handpiece at the base
handpiece slot. Insert power cable on
power socket at right lateral of the
base (1). Once cable is connected to
base a battery icon will appear (2)
showing status of battery. A blinking
light indicates that the battery is being
charged.
Touch and hold power (1) for 3
seconds. Display will show the last
working mode chosen. To change the
operation mode press En-Ap (2). Motor
and apex locator combined mode (3) is
preferred. Press on/off button on the
handpiece to enter ready-on.
Touch SYSTEM (1) to selet Preferred
File System (2).
Press Auto Rev (1) to set up the
preferred auto reverse mode.
2- Auto reverse on
3- Auto stop on
4- Auto reverse/auto stop off (4).
Auto-reverse on is recommended
For More Information:
Quick Start Guide| Installation &Setup
Align locating pins of contra-angle with
the positioning slots on the motor and
push the contra-angle horizontally. A
“click” will indicate the installation is in
place.
User-defined system in rotation:
Touch SYSTEM (1) to select program
(2). Touch FILE (3) to select file . Set
up speed, torque, and auto-reverse
mode using the equivalent SPEED,
TORQUE, and Auto-Rev buttons.
User-defined system in reciprocation:
Touch SYSTEM (1) to select
reciprocating (2). Touch FILE (3) to
select file. 1. Set up speed and torque,
using the equivalent SPEED, TORQUE
buttons. Touch SET (4) to switch
between forward & reverse (5). Touch
ANGLE (6) to set up angles.
For AutoSense:
Touch SYSTEM (1) to select
AutoSense . Use the SUHIHUUHGILOHV in
sequence. Sensitivity to turn
rotary>>reciprocation>>rotary can be
selected by touching TORQUE button
up or down (2).
Touch and hold SET (1) to set up
sub-settings. Touch ANGLE (2) to
determine the apical position alarm (3).
Position 00 (foreamen exit) is
recommended.
Touch and hold SET (1) to set up
sub-settings. Touch SPEED to select
(2) apical reverse/apical stop; auto
start and apical slow down (3).
To activate/deactivate any of the
selections press En-Ap (4).
Place the handpiece at the base
handpiece slot. Insert power cable on
power socket at right lateral of the
base(1). Once cable is connected to
base a battery icon will appear(2)
showing status of battery. A blinking
light (3) indicates that the battery is
being charged.
Touch and hold power(1) for 3
seconds. Display will show the last
working mode chosen. To change the
operation mode press En-Ap(2).Motor
and apex locator combined mode(3)is
preferred. Press on/off button on the
handpiece to enter ready-on.
Touch SYSTEM (1) to select
SUHIHUHGILOHVV\VWHP (2).
Press Auto Rev(1)to set up the
preferred auto reverse mode.
2- Auto-reverse on
3- Auto stop on
4- Auto-reverse/auto stop off .
Auto-reverse on is recommended
iPlus
PAC
ENDO
909.839.0888
[email protected]
670 Endeavor Circle, Brea, CA 92821
www.pac-dent.com
Rev.031821#06INTRPCL02A
For More Information:
Quick Start Guide| Installation &Setup
Align locating pins of contra-angle with
the positioning slots on the motor and
push the contra-angle horizontally. A
“click” will indicate the installation is in
place.
User-defined system in rotation:
Touch SYSTEM (1) to select program
(2). Touch FILE (3) to select file . Set
up speed, torque, and auto-reverse
mode using the equivalent SPEED,
TORQUE, and Auto-Rev buttons.
User-defined system in reciprocation:
Touch SYSTEM (1) to select
reciprocating (2). Touch FILE (3) to
select file. 1. Set up speed and torque,
using the equivalent SPEED, TORQUE
buttons. Touch SET (4) to switch
between forward & reverse (5). Touch
ANGLE (6) to set up angles.
For AutoSense:
Touch SYSTEM (1) to select
AutoSense . Use the SUHIHUUHGILOHV in
sequence. Sensitivity to turn
rotary>>reciprocation>>rotary can be
selected by touching TORQUE button
up or down (2).
Touch and hold SET (1) to set up
sub-settings. Touch ANGLE (2) to
determine the apical position alarm (3).
Position 00 (foreamen exit) is
recommended.
Touch and hold SET (1) to set up
sub-settings. Touch SPEED to select
(2) apical reverse/apical stop; auto
start and apical slow down (3).
To activate/deactivate any of the
selections press En-Ap (4).
Place the handpiece at the base
handpiece slot. Insert power cable on
power socket at right lateral of the
base(1). Once cable is connected to
base a battery icon will appear(2)
showing status of battery. A blinking
light (3) indicates that the battery is
being charged.
Touch and hold power(1) for 3
seconds. Display will show the last
working mode chosen. To change the
operation mode press En-Ap(2).Motor
and apex locator combined mode(3)is
preferred. Press on/off button on the
handpiece to enter ready-on.
Touch SYSTEM (1) to select
SUHIHUHGILOHVV\VWHP (2).
Press Auto Rev(1)to set up the
preferred auto reverse mode.
2- Auto-reverse on
3- Auto stop on
4- Auto-reverse/auto stop off .
Auto-reverse on is recommended
iPlus
PACENDO
909.839.0888
[email protected]
670 Endeavor Circle, Brea, CA 92821
www.pac-dent.com
Rev.031821#06INTRPCL02A
CX-C1
PAC-TAPER
CX-C1
PAC-TAPER
CX-C1
PAC-TAPER
CX-C1
PAC-TAPER
1
1
2
2
22
3
4
33
1 1
11
3
4 1 14
3
6 2
1
2 2
2
2
5
2
3
For More Information:
Quick Start Guide| Installation & Setup
Align locating pins of contra-angle with
the positioning slots on the motor and
push the contra-angle horizontally. A
“click” will indicate the installation is in
place.
User-defined system in rotation:
Touch SYSTEM (1) to select program
(2). Touch FILE (3) to select file . Set
up speed, torque, and auto-reverse
mode using the equivalent SPEED,
TORQUE, and Auto-Rev buttons.
User-defined system in reciprocation:
Touch SYSTEM (1) to select
reciprocating (2). Touch FILE (3) to
select file. 1. Set up speed and torque,
using the equivalent SPEED, TORQUE
buttons. Touch SET (4) to switch
between forward & reverse (5). Touch
ANGLE (6) to set up angles.
For AutoSense:
Touch SYSTEM (1) to select
AutoSense . Use the preferred les in
sequence. Sensitivity to turn
rotary>>reciprocation>>rotary can be
selected by touching TORQUE button
up or down (2).
Touch and hold SET (1) to set up
sub-settings. Touch ANGLE (2) to
determine the apical position alarm (3).
Position 00 (foreamen exit) is
recommended.
Touch and hold SET (1) to set up
sub-settings. Touch SPEED to select
(2) apical reverse/apical stop; auto
start and apical slow down (3).
To activate/deactivate any of the
selections press En-Ap (4).
Place the handpiece at the base
handpiece slot. Insert power cable on
power socket at right lateral of the
base(1). Once cable is connected to
base a battery icon will appear(2)
showing status of battery. A blinking
light (3) indicates that the battery is
being charged.
Touch and hold power(1) for 3
seconds. Display will show the last
working mode chosen. To change the
operation mode press En-Ap(2).Motor
and apex locator combined mode(3)is
preferred. Press on/off button on the
handpiece to enter ready-on.
Touch SYSTEM (1) to select
prefered le's system (2).
Press Auto Rev(1)to set up the
preferred auto reverse mode.
2- Auto-reverse on
3- Auto stop on
4- Auto-reverse/auto stop off .
Auto-reverse on is recommended
iPlus
PAC ENDO

EJBKĤL=?@AJP?KI
"J@A=RKN EN?HANA= 
SSSL=?@AJP?KI
CX-C1
PAC-TAPER
CX-C1
PAC-TAPER
1
2
3
1
1
1