PAC P1C-GM12 User manual

INSTALLATION
MANUAL
VIDEO
INTEGRATION MODULE
This manual shows the install into a single applicable vehicle. Other vehicle
disassembly will vary. wiring remains the same with all vehicles.
See application guide for applicable vehicles

2

3
INTERFACE DIP SWITCH SETTINGS
DIP ON OFF
DIP 1 A/V 1 ON A/V 1 OFF
DIP 2 A/V 2 ON A/V 2 OFF
DIP 3 A/V 3 ON A/V 3 OFF
DIP 4 AFTERMARKET CAMERA OEM CAMERA
DIP 5 4.2” SCREEN 8”SCREEN
DIP 6 TOUCH SCREEN CALIBRATION ON TOUCH SCREEN CALIBRATION OFF
 DIP SWITCH SETTINGS MUST BE PERFORMED WITH UNIT POWERED OFF.
IT WILL NOT CAUSE DAMAGE, BUT THE FUNCTION WILL NOT BE
RECOGNIZED UNTIL POWER CYCLES.
 YOU MUST CALIBRATE THE TOUCHSCREEN IN ON THE INTERFACE AS
WELL AS THE NAVIGATION BRAIN FOR 4.2” MODEL.
A/V FUNCTIONS
 THIS UNIT SUPPORTS THREE AUDIO/VIDEO INPUTS. AND ONE
AUDIO/VIDEO OUTPUT.

4
RADIO CONTROL PANEL

5
RADIO CONTROL PANEL
BUTTON FUNCTIONS
 HOME BUTTON FUNCTIONS ARE DETERMIDED BY THE “HOME” BUTTON
SELECTED IN THE INTERFACE SETTINGS MENU. YOU CAN SELECT ANY
BUTTON TO BE THE “HOME” BUTTON IN THE HOME BUTTON
PROGRAMMING SECTION OF THE INTERFACE SETTINGS.
BUTTON WHEN PRESSED IN NAV SCREEN WHEN PRESSED IN FACTORY
SCREEN
HOME 1 SEC = SWITCH BETWEEN A/V SOURCE 3 SEC = SWITCH TO INTERFACE
BACK SWITCH TO PREVIOUS FACTORY SCREEN FACTORY FUNCTION
RADIO THIS WILL SWITCH SOURCE WITHOUT
EXITING NAV SCREEN FACTORY FUNCTION
MENU BACK TO MAIN MENU FACTORY FUNCTION
|<< >>| THIS WILL SEEK WITHOUT EXITING NAV
SCREEN FACTORY FUNCTION

6
 REMOVE TRIM BEZEL AROUND RADIO.
SET ASIDE.
 REMOVE FOUR 7MM SCREWS FROM
THE CORNERS OF THE CONTROL PANEL.
 GENTLY PULL ON CONTROL PANEL TO
RELEASE THE TWO CLIPS LOCATED ON
THE SIDES.
 UNPLUG ALL PLUGS FROM CONTROL
PANEL AND SET IT ASIDE.
*SILVERADO DISASSEMBLY SHOWN, OTHER VEHICLES WILL VARY

7
 PLUG SUPPLIED T-HARNESS (TWO)
INTO THE CONNECTIONS ON THE BACK
OF THE CONTROL PANEL. .
 T-HARNESSES PLUGGED IN.
 PLUG MOLEX CONNECTOR FROM T-
HARNESS INTO THE MAIN HARNESS.
 ROUTE MAIN HARNESS TO DESIRED
LOCATION OF INTERFACE BOX.

8
 PLUG TWO CONNECTORS INTO
INTERFACE. THE OTHER CONNECTORS
SHOWN IN THIS PICTURE (3PIN & 2PIN)
ARE FOR DVD IR AND ARE NOT NEEDED
UNLESS INSTALLING AN AFTERMARKET
DVD PLAYER NEEDING TOUCH
CONTROL.
 PLUG LVDS T-HARNESS INTO LVDS
SOCKET. THERE ARE GUIDES LOCATED
ON PLUG TO ALIGN IT CORRECTLY. BE
SURE TO PLUG IN CORRECTLY. DO NOT
FORCE. ROUTE THE CABLE AND SECURE
WITH CABLE TIES.
 ONCE ALL CONNECTIONS HAVE BEEN
MADE TO INTERFACE AND
NAVIGATION BOX, PLUG THE LVDS
AND 10 PIN T-HARNESSES BACK INTO
THE CONTROL PANEL AND SNAP
CONTROL PANEL BACK INTO THE DASH.
 TURN THE IGNIGTION ON, ONCE THE
UNIT BOOTS AND THE DISPLAY IS
ACTIVE, PRESS AND HOLD THE “HOME”
KEY FOR 20 SECONDS UNTIL THE
INTERFACE SWITCHES TO NAVI MODE.

9
 ONCE IN THE NAVI MODE PRESS AND
HOLD THE TOUCH SCREEN FOR ABOUT
8 SECONDS UNTIL THE INTERFACE
MENU DISPLAYS.
 ONCE INSIDE THE MENU, CHOOSE THE
HOME BUTTON LEARNING BY PRESSING
START.
 ONCE THIS IS DONE, PRESS THE HOME
BUTTON ON THE RADIO AGAIN TO
LEARN THAT BUTTON FOR THE
SWITCHING OF NAVIGATION, A/V1,2,3,
AND FACTORY DISPLAY. ONCE THIS IS
DONE IT WILL ONLY TAKE 3 SECOND TO
SWITCH THE INTERFACE WHEN
PRESSING THIS BUTTON.
 YOU CAN ALSO ADJUST THE
BRIGHTNESS AND CONTRAST OF THE
INTERFACE HERE.

10