©2017 PAC | PAC is a Power Brand of AAMP Global
www.pac-audio.com
Rev. 020717 Page 2
$GYDQFHG$PSOL¿HU,QWHUIDFHIRU
6HOHFW&KU\VOHU'RGJH9HKLFOHV
AP4-CH31
6HWXSDQG&RQ¿JXUDWLRQ
1. Turn the ignition on. LED 1 on the interface will turn on and the +12v remote output will turn on.
2. 6HWWKHDPSJDLQVWRWKHGHVLUHGOHYHO:HUHFRPPHQGXVLQJDQRVFLOOLVFRSHDQGWHVWWRQHVWRVHWWKHDPSJDLQV3OHDVH
UHIHUWRWKH0(&3$GYDQFHGVWXG\JXLGHSLI\RXDUHXQIDPLOLDUZLWKWKLVSURFHVV
3. Check volume, balance, fade and EQ settings.
4. If you would like to adjust the minimum volume, do so using one of the methods outlined below. If you are happy with the
default level, no adjustment is necessary.
0DQXDOO\6HWWLQJWKH0LQLPXP9ROXPH
If the minimum volume of the radio (factory radio volume level 1) is too loud, you can manually set the level of the minimum
volume using either the programming button on the side of the interface or the factory SWC. If you would like to set the
PLQLPXPYROXPHXVLQJWKH$PS3523&DSSSOHDVHSURFHHGWRWKH$PS3523&DSSVHFWLRQRQSDJH
3/($6(127(/HYHOFRQWURONQREPXVWEHFRQQHFWHGWRPRGXOHIRUHLWKHURIWKHIROORZLQJPHWKRGV
6HWWLQJWKHPLQLPXPYROXPHXVLQJWKHSURJUDPPLQJEXWWRQ
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Set the amp gains to the desired level.
3. Set the volume on the factory radio to 1.
4. 3UHVVWKHSURJUDPPLQJEXWWRQRQWKHVLGHRIWKHLQWHUIDFHRQFH
5. /('ZLOOWXUQDPEHUDQGWKHFKLPHVZLOOEHJLQEHHSLQJHYHU\¿YHVHFRQGV
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.
6HWWLQJWKHPLQLPXPYROXPHXVLQJIDFWRU\EXWWRQV
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Set the amp gains to the desired level.
3. Set the volume on the factory radio to 1.
4. 3UHVVDQGKROGWKH(QWHU%URZVHEXWWRQRQWKHIDFWRU\UDGLRPLGGOHEXWWRQRQULJKWNQREIRUDSSUR[LPDWHO\WHQVHFRQGV
3/($6(127(7KHUDGLRPD\UHVSRQGWRWKHEXWWRQSUHVVGXULQJWKLVSURFHVVWKLVLVQRUPDODQGKDVQRHIIHFWRQWKH$3
operation.
5. /('ZLOOWXUQDPEHUDQGWKHFKLPHVZLOOEHJLQEHHSLQJHYHU\¿YHVHFRQGV
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.
Installation
1. 5HPRYHIDFWRU\UDGLR
2. Disconnect the main 22-pin factory harness from radio.
3. &RQQHFW$PS352KDUQHVVWRYHKLFOHKDUQHVV
4. &RQQHFW$PS352KDUQHVVWRIDFWRU\UDGLR
5. 6HWDQ\IHDWXUH',3VZLWFKHVWKDWDSSO\WR\RXULQVWDOO
a.6HW',3VZLWFKRQGRZQWRVHQGDOOUHDUSDUNLQJVHQVRUFKLPHVWKURXJKWKHIURQWFKDQQHO7KLVVKRXOGEHXVHGZKHQ
WKHYHKLFOHLVHTXLSSHGZLWKUHDUSDUNLQJVHQVRUVDQG\RXDUHHLWKHUXVLQJWKH726/,1.RXWSXWRUUXQQLQJDOOFDELQ
VSHDNHUVRIIRIWKHIURQWRXWSXWVRIWKH$3
b.6HW',3VZLWFKRQGRZQWRORZHUWKH5&$RXWSXWYROWDJHWRY/HDYH',3VZLWFKRIIXSWRNHHSWKH5&$RXWSXW
voltage at 5v. See troubleshooting section on page 4 for more details.
c. ',3VZLWFKHVDQGDUHQRWXVHG
6. ,I\RXDUHXVLQJWKH$3$726VROGVHSDUDWHO\UHIHUWRWKHLQVWUXFWLRQVLQFOXGHGZLWKWKDWSURGXFWIRULWVLQVWDOODWLRQ
7. &RQQHFWWKH$PS352KDUQHVVWRWKHPRGXOH
8. Connect the level control knob to the module and install in an accessible location.
9. &RQQHFWWKHVLJQDOFDEOHVDQGUHPRWHLQSXWIURPWKHDIWHUPDUNHWDPSOL¿HU
DIP
1234
ON
5HDU&KLPH3DWK YY3UHRXW No Function No Function
12 3 4
6HW',3VZLWFKHVWRWKH21SRVLWLRQWRDFWLYDWHWKHFRUUHVSRQGLQJIHDWXUHV
6HW',3VZLWFKHVWRWKH2))SRVLWLRQIRUDQ\IHDWXUHVWKDWDUHQRWGHVLUHG
