Paloma PH-28 User manual

The purpose of this manual is to provide the installer
with the basic instructions necessary to properly install
the pipe cover assembly. This manual assumes that the
installer has basic skills and plumbing knowledge. Local
codes may apply to this installation. All local building,
electrical, and plumbing codes should be followed.
It is very important that all persons who are expected to
install, operate or adjust this pipe cover assembly and/or
water heater, read these instructions along with those
instructions provided with the tankless water heater.
Recognize this symbol as an indication of
Important Safety Information!
Refer to the Use and Care Manual provided with
your tankless water heater for the proper installa-
tion procedures and requirments.
!
Location - This pipe cover is for indoor or outdoor
installations and should be installed directly to the bot-
tom of the water heater. The water heater is not included
with the pipe cover assembly.
The water heater must be installed in accordance with
the Use and Care Manual provided with the water heater.
All considerations of the use and care manual along with
any applicable local codes must be followed.
Dimensions and Piping - The box extends ap-
proximately 16 inches below the bottom of the water
heater. Piping for water, gas, and connections for elec-
trical should penetrate the wall within 16 inches from
the bottom of the water heater. Provisions should be
made for cut off valves and service unions.
WARNING!
liquids (adhesives, solvents, paint thinners etc.), and the
vapors they produce are extremely dangerous. DO NOT
-
water heater or any other appliance. Be sure to read and
-
ing printed in this manual. Failure to do so can result in
!
For use with these models of Indoor or Outdoor Tan-
kless Water Heaters;
PH-28 (ROFS/COFS/RIFS/CIFS)
Water Heater
Hot Water
Valve
Cold Water
Valve
Power
Disconnect
Gas
Shut
Off
Unions
Wall
Mounting
Screws
(not included)
Pipe Cover
Assembly
Upper
Mounting
Screws
Relief Valve
Relief
Valve Drain
Typical Installation - Outdoor - Figure 1
Water Heater Not Provided
Follow instructions in
Use and Care provided
with the water heater.
AP14005 (04/06)
Tankless Water Heater Pipe Cover Assembly
Installation Instructions
R

or the assembly may become deformed. Slide the pipe
the screws are in the slots.
There are two holes for securing the pipe cover to the
wall, one on each side near the bottom. Mark these hole
locations on the wall. Carefully take the pipe cover off
the water heater and drill pilot holes for a #8 or #10
screw (not provided) in the wall.
Position the pipe cover back onto the water heater, slide
back into place and secure the screws on the side of the
water heater and fasten to the wall.
Outdoor installations
The relief valve may be plumbed so that it passes through
the opening in the bottom of the pipe cover. Additional
holes may be drilled through the pipe cover if needed.
It is recommended that the sides of the pipe cover next
4). Weather resistant insulation may be used to cover
the pipes in cold climates.
Pipe Cover Installation
Once the water heater is mounted and installed prepare for
the pipe cover installation. Remove the front cover from
the pipe cover assembly by removing the two screws.
On each side of the water heater are three (3) large
the front and back screws only, so that about 1/8 of an
inch of the threads show. Do not completely remove the
screws from the side of the water heater.
Once all four (4) screws have been loosened, slip the
pipe cover over each side. The screws in the water heat-
-
er. You may have to gently spread the sides of the pipe
Loosen Screws
Water Heater
Slotted Holes
Pipe Cover
Grounded
Power Plug
Water Heater
Hot Water
Valve
Cold Water
Valve
Power
Cord
(pass plug through hole in bottom
of the pipe cover assembly)
Gas
Shut
Off
Unions
Wall
Mounting
Screws
(not included)
Upper
Mounting
Screws
Relief Valve
Grounded
Electrical
Outlet
Typical Installation - Indoor - Figure 3
Pipe Cover Installation - Figure 2
Indoor installations
Pass the plug of the power cord through the opening
pipes, gas, water, and relief valves, should be plumbed
into the wall.
Front Access Cover
Slip the tabs on the bottom of the cover into the slots
at the base of the pipe cover assembly. Close cover and
secure with the two screws provided.
Technical Service
For questions regarding the installation of this pipe cov-
er assembly, please contact Technical Service at 1-800-
605-6542.
Finished Installation - Outdoor - Figure 4
Side
Water
Heater
Pipe Cover
Assembly
Upper
Mounting
Screws
Caulk