Panasonic HC-V785 User manual

Operating Instructions
High Definition Video Camera
Model No. HC-V785
Please read these instructions carefully before using this product,and save this manual for future
use.
DVQP1272ZA
until
2017/02/28

- 2 -
∫About the recording format for
recording motion pictures
You can select from AVCHD*1, MP4 or iFrame
recording formats to record motion pictures
using this unit. (l70)
*1 It is compatible with the AVCHD
Progressive (1080/50p).
AVCHD:
It is suitable for viewing on a high-definition TV
or for saving to disc*2.
*2 The following methods are available for
saving an image recorded in 1080/50p:
jCopy the image to a disc using the
HD Writer AE 5.2.
jCopy the image to a Panasonic Blu-ray
disc recorder that supports AVCHD
Progressive.
MP4:
This is a recording format suitable for playing
back or editing on a PC.
≥It is not compatible with motion pictures
recorded in AVCHD format.
iFrame:
This is a recording format suitable for playing
back or editing on a Mac (iMovie etc.).
≥It is not compatible with motion pictures
recorded in AVCHD format.
∫Indemnity about recorded
content
Panasonic does not accept any responsibility
for damages directly or indirectly due to any
type of problems that result in loss of recording
or edited content, and does not guarantee any
content if recording or editing does not work
properly. Likewise, the above also applies in a
case where any type of repair is made to the
unit.
∫About Condensation (When
the lens or the LCD monitor is
fogged up)
Condensation occurs when there is a change in
temperature or humidity, such as when the unit
is taken from outside or a cold room to a warm
room. Please be careful, as it may cause the
lens or LCD monitor to become soiled, moldy,
or damaged.
When taking the unit to a place which has a
different temperature, if the unit is accustomed
to the room temperature of the destination for
about one hour, condensation can be
prevented. (When the difference in temperature
is severe, place the unit in a plastic bag or the
like, remove air from the bag, and seal the bag.)
When condensation has occurred, remove the
battery and/or the AC adapter and leave the
unit like that for about one hour. When the unit
becomes accustomed to the surrounding
temperature, fogginess will disappear naturally.
∫Cards that you can use with
this unit
SD Memory Card, SDHC Memory Card and
SDXC Memory Card
≥4 GB or more Memory Cards that do not have
the SDHC logo or 48 GB or more Memory
Cards that do not have the SDXC logo are
not based on SD Memory Card
Specifications.
≥Refer to page 14 for more details on SD
cards.
Read this first

- 3 -
∫For the purposes of these
operating instructions
≥SD Memory Card, SDHC Memory Card and
SDXC Memory Card are referred to as the
“SD card”.
≥The smartphone and tablet are indicated as
“smartphone”.
≥Function that can be used for Motion Picture
Recording Mode:
Function that can be used for Still Picture
Recording Mode:
≥Function that can be used for the Playback
Mode:
Function that can be used for the Playback
Mode (motion pictures only):
Function that can be used for the Playback
Mode (still pictures only):
≥Scene(s) recorded in the recording format
[AVCHD]: “AVCHD scene(s)”
≥Scene(s) recorded in the recording format
[MP4/iFrame], scene(s) saved in
MP4 (1920k1080/25p), MP4 (1280k720/
25p) or MP4 (640k360/25p): “MP4/iFrame
scene(s)”
≥Scene(s) recorded in the recording mode
[iFrame]: “iFrame scene(s)”
≥Scene(s) containing only the Main Camera’s
image that was recorded separately from a
simultaneously recorded normal scene when
[Backup for Twin Camera] was set to [ON]:
Scene(s) recorded as Backup for Twin
Camera
≥Pages for reference are indicated by an
arrow, for example: l00

- 4 -
Read this first .................................................2
Preparation
Names and Functions of Main Parts ............ 7
Power supply................................................ 10
Inserting/removing the battery ............... 10
Charging the battery .............................. 11
Charging and recording time ................. 12
Recording to a card ..................................... 14
Cards that you can use with this unit..... 14
Inserting/removing an SD card .............. 15
Turning the unit on/off ................................. 16
Selecting a mode ......................................... 17
Switching this unit between Recording
Mode and Playback Mode ..................... 17
Switching this unit between
Motion Picture Recording Mode and
Still Picture Recording Mode ................. 17
How to use the touch screen ...................... 18
About the Touch Menu........................... 19
Setting date and time................................... 20
Basic
Before recording .......................................... 21
Recording motion pictures ......................... 22
Recording still pictures ............................... 24
Recording still pictures in
Motion Picture Recording Mode ............ 25
Motion picture/Still picture playback ......... 26
Using the menu screen ............................... 29
Using the Setup Menu ................................. 30
Advanced (Recording)
Using the zoom ............................................41
Zoom ratio during the Still Picture
Recording Mode..................................... 41
Level Shot Function.....................................42
Recording with the Backup for
Twin Camera Function .................................43
Changing the Recording Mode ...................44
Intelligent Auto ....................................... 45
Intelligent Auto Plus ............................... 47
Creative Control ..................................... 47
HDR Movie Mode................................... 50
Scene Mode........................................... 51
FULL HD Slow Motion Video ................. 52
Stop Motion Animation Assist ................ 54
Manual recording .........................................55
White Balance........................................ 56
Manual shutter speed/iris adjustment .... 57
Manual Focus adjustment...................... 58
Recording with the Touch Function ...........59
Touch function icons .............................. 59
Recording functions of operation icons ....64
Operation icons...................................... 64
Recording functions of menus ...................69
Contents

- 5 -
Advanced (Playback)
Playback Operations ................................... 81
Motion picture playback using
operation icon ........................................ 81
Creating still picture from
motion picture ........................................ 83
Highlight & Time Frame Index ............... 83
Repeat Playback ................................... 84
Resuming the previous playback........... 84
Setting the playback speed of
FULL HD Slow Motion Video ................. 84
Zooming in on a still picture during
playback (Playback zoom)..................... 85
Various playback functions ........................ 86
Playing back motion pictures/
still pictures by date ............................... 86
Highlight Playback ................................. 88
Manual Edit............................................ 94
Baby Calendar....................................... 97
Changing the playback settings and
playing back the slide show................... 99
Playing back still pictures recorded
in Stop Motion Animation Assist Mode
as a slide show .................................... 101
Deleting scenes/still pictures ................... 102
Deleting part of a scene (AVCHD/
Backup for Twin Camera) .................... 104
Dividing a scene (AVCHD/
Backup for Twin Camera) .................... 105
Dividing a scene to partially delete
(MP4/iFrame)....................................... 106
Protecting scenes/still pictures ............ 107
Convert to MP4........................................... 108
Slow speed conversion ............................. 109
Watching Video/Pictures on your TV ....... 110
Connecting with a HDMI micro cable .... 112
Listening in 5.1 channel sound
(AVCHD).............................................. 112
Playback using VIERA Link ...................... 113
Copy/Dubbing
Copying/playing back with a USB HDD ... 115
Preparing for copying/playing back...... 115
Simple copy ......................................... 118
Copy selected files............................... 118
Playing back the USB HDD ................. 119
Dubbing with a Blu-ray disc recorder,
video device, etc. .......................................120
Using the Eye-Fi™ card.............................124
Wi-Fi
Wi-Fi® function ...........................................127
[Remote Ctrl] ..............................................129
Preparations before using
[Remote Ctrl]........................................ 130
Using [Remote Ctrl] with a
direct connection.................................. 131
Using [Remote Ctrl] with a
wireless access point connection......... 131
About [Remote Ctrl] ............................. 132
[Baby Monitor]............................................134
Preparations before using
[Baby Monitor]...................................... 134
Using [Baby Monitor]............................ 135
[Hom.Monitor].............................................137
Preparations before using
[Hom.Monitor] ...................................... 137
Using [Hom.Monitor] ............................ 138
[DLNA Play] ................................................143
Preparations before using
[DLNA Play] ......................................... 143
Playing back on a TV ........................... 144
[Copy] ..........................................................145
Preparations before using [Copy] ........ 145
Copying to a PC................................... 147
[Live Cast]...................................................149
Preparations before using [Live Cast] ..... 150
Broadcasting live.................................. 151
Install the “Image App”..............................155
Setting Up a Wi-Fi Connection..................156
Using the [Wi-Fi Setup Wizard] to
set up a connection.............................. 157
Connecting to a wireless
access point ......................................... 158
Setting up a direct connection to a
smartphone .......................................... 161
Connecting from the history ................. 163
If the Wi-Fi connection cannot be
established........................................... 164
How to Use the [Wi-Fi Setup] Menu..........166

- 6 -
Wireless Twin Camera
Wireless Twin Camera function................ 172
Notes on the Wireless Twin Camera
function ................................................ 173
Using a Smartphone as a Wireless Sub
Camera........................................................ 174
When connecting a smartphone to
this unit as a Wireless Sub Camera
for the first time .................................... 175
When connecting for the second time
or later ................................................. 177
Terminating the connection.................. 177
Recording with a Wireless Sub Camera
(Wireless Twin Camera)............................. 178
Screen display when using a
Wireless Sub Camera.......................... 178
If the Wi-Fi connection cannot be
established (Wireless Twin Camera) ........ 182
With a PC
What you can do with a PC ....................... 183
Before Installing HD Writer AE 5.2 ...... 185
Operating environment ............................. 187
Installation .................................................. 189
Connecting to a PC.................................... 190
About the PC display ........................... 192
Starting HD Writer AE 5.2 .......................... 193
Reading the operating instructions of
the software applications ..................... 193
If using Mac (mass storage)...................... 194
Others
Indications ..................................................195
Messages ....................................................198
About recovery..................................... 199
Troubleshooting .........................................200
Cautions for use .........................................206
About copyright .........................................210
Recording modes/
approximate recordable time .................... 211
Approximate number of
recordable pictures....................................212
Optional accessories .................................213
About the Remote Pan Tilt Cradle ........214

- 7 -
1Speaker
2Shoe adaptor release lever
[SHOE ADAPTOR RELEASE] (l213)
3Recording/playback button [ / ]
(l17)
4Level Shot Function button [ ]
(l42)
5Power button [ ] (l16)
6Battery release lever [BATT] (l10)
7USB terminal [] (l115, 121, 190)
8Micro HDMI connector [HDMI]
(l110)
9A/V connector [A/V] (l110, 123)
10 Microphone terminal [MIC]
≥A compatible plug-in powered microphone
can be used as an external microphone.
≥If you connect an external microphone when
a setting other than [AUTO] is selected for
[MIC LEVEL] (l77), (Microphone
input level meter) will be displayed.
≥When the unit is connected with the AC
adaptor, sometimes noise may be heard
depending on the microphone type. In this
case, please switch to the battery for the
power supply and the noise will stop.
11 Internal microphones
12 Lens cover
≥The lens cover opens in Motion Picture
Recording Mode or Still Picture Recording
Mode. (l17)
13 Multi Manual Dial [CAMERA FUNCTION]
(l55, 78)
14 Video light (l67,80)
15 Lens
Preparation
Names and Functions of Main Parts
123
4
5
6
8107
ヮリヤモバヷ
9
12
13
14
15
11

- 8 -
16 Shoe adaptor mounting part
[SHOE ADAPTOR] (l213)
17 Status indicator (l16, 156)
18 Recording start/stop button (l22)
19 LCD monitor (Touch screen) (l18)
≥It can open up to 90o.
≥It can rotate up to 180o A towards the lens or
90o B towards the opposite direction.
20 Battery holder (l10)
21 Shoulder strap fixture
22 Tripod receptacle
≥Attaching a tripod with a screw length of
5.5 mm or more may damage the unit.
23 SD card cover (l15)
24 Access lamp [ACCESS] (l15)
25 Card slot (l15)
26 Photoshot button [ ] (l24)
27 Zoom lever [W/T] (In Motion Picture
Recording Mode or Still Picture
Recording Mode) (l41)/
Thumbnail display switch [ / ]/
Volume lever [sVOLr] (In Playback
Mode) (l28)
17
16
212019
18
22
23 24
25
26
27


- 9 -
28 Grip belt
Adjust the length of the grip belt so that it fits
your hand.
1Flip the belt.
2Adjust the length.
3Replace the belt.
29 Headphone terminal [ ] (l68)
≥Excessive sound pressure from earphones
and headphones can cause hearing loss.
≥Listening at full volume for long periods may
damage the user’s ears.
30 DC input terminal [DC IN] (l11)
≥Do not use any other AC adaptors except the
supplied one.
31 Wi-Fi button [Wi-Fi]
(l129, 134, 137, 143, 145, 149, 163, 166)
32 Wi-Fi Transmitter (l128)
28
30
29



31
32

- 10 -
∫About batteries that you can use with this unit
The battery that can be used with this unit is VW-VBT190/VW-VBT380.
≥The unit has a function for distinguishing batteries which can be used safely. The
dedicated battery (VW-VBT190/VW-VBT380) supports this function. The only batteries
suitable for use with this unit are genuine Panasonic products and batteries manufactured
by other companies and certified by Panasonic. Panasonic cannot in any way guarantee
the quality, performance or safety of batteries which have been manufactured by other
companies and are not genuine Panasonic products.
Inserting/removing the battery
≥Press the power button to turn off the unit. (l16)
Install the battery by inserting it in the direction shown in the figure.
Preparation
Power supply
It has been found that counterfeit battery packs which look very similar to the genuine
product are made available to purchase in some markets. Some of these battery packs
are not adequately protected with internal protection to meet the requirements of
appropriate safety standards. There is a possibility that these battery packs may lead to
fire or explosion. Please be advised that we are not liable for any accident or failure
occurring as a result of use of a counterfeit battery pack. To ensure that safe products are
used we would recommend that a genuine Panasonic battery pack is used.
Removing the battery
Be sure to hold down the power button until
the status indicator goes off. Then remove the
battery while supporting the unit to prevent it
from dropping.
Move the battery release lever in the
direction indicated by the arrow and
remove the battery when unlocked.
ャモヵヵ
Insert the battery until it clicks and locks.

- 11 -
Charging the battery
The unit is in the standby condition when the AC adaptor is connected. The primary circuit is always
“live” as long as the AC adaptor is connected to an electrical outlet.
Important:
≥Do not use the AC adaptor/DC cable with any other equipment as it is designed only for
this unit. Also, do not use the AC adaptor/DC cable from other equipment with this unit.
≥The battery will not be charged if the unit is turned on.
≥It is recommended to charge the battery in a temperature between 10 oC and 30 oC. (The
battery temperature should also be the same.)
ADC input terminal
1Connect the DC cable to the AC adaptor and to the DC input terminal of this
unit.
≥Insert the plugs as far as they will go.
2Insert the AC adaptor into an AC outlet.
≥The status indicator will flash red at an interval of approximately 2 seconds (approximately
1 second on, approximately 1 second off), indicating that charging has begun.
It will turn off when the charging is completed.
∫Connecting to the AC outlet
It is possible to use this unit with power supplied from the AC outlet by turning on the unit with the
AC adaptor connected.
Even when you use the AC adaptor for recording images, keep the battery connected.
This allows you to continue the recording even if a power failure occurs or the AC adaptor is
unplugged from the AC outlet by accident.
When this unit is purchased, the battery is not charged. Charge the battery fully before
using this unit for the first time.


- 12 -
∫To charge by connecting to other device
It is possible to charge by connecting to other device with the USB cable (supplied).
Please refer to page 191.
≥If the status indicator flashes at a particularly fast or slow rate, refer to page 208.
≥We recommend using Panasonic batteries (l12).
≥If you use other batteries, we cannot guarantee the quality of this product.
≥Do not heat or expose to flame.
≥Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with
doors and windows closed.
Charging and recording time
∫Charging/Recording time
≥The indicated charging time is for when the battery has been discharged completely.
Charging time and recordable time vary depending on the usage conditions such as high/
low temperature.
≥Temperature: 25 oC/humidity: 60%RH
≥Charging times in parentheses are when charging from the USB terminal.
≥“h” is an abbreviation for hour, “min” for minute and “s” for second.
≥These times are approximations.
Battery model
number
[Voltage/Capacity
(minimum)]
Charging
time
Recording
format
Recording
mode
Maximum
continuous
recordable
time
Actual
recordable
time
Supplied battery/
VW-VBT190
(optional)
[3.6 V/1940 mAh]
2h20min
(5h20min)
[AVCHD]
[1080/50p]
1h45min 55min
[PH],[HA]
[HG],[HE]
[MP4/
iFrame]
[1080/50M] 1 h 40 min 50 min
[1080/28M] 1 h 45 min 55 min
[720] 2h 1h
[iFrame]
Battery model
number
[Voltage/Capacity
(minimum)]
Charging
time
Recording
format
Recording
mode
Maximum
continuous
recordable
time
Actual
recordable
time
VW-VBT380
(optional)
[3.6 V/3880 mAh]
3h45min
(9h45min)
[AVCHD]
[1080/50p] 3 h 40 min
1h55min
[PH]
3h45min
[HA]
[HG],[HE]
[MP4/
iFrame]
[1080/50M] 3 h 35 min 1 h 50 min
[1080/28M] 3 h 40 min 1 h 55 min
[720] 4h10min 2h10min
[iFrame] 4 h 15 min

- 13 -
≥The actual recordable time refers to the recordable time when repeatedly starting/stopping
recording, turning the unit on/off, moving the zoom lever etc.
≥The batteries heat up after use or charging. This is not a malfunction.
Battery capacity indication
≥The display changes as the battery capacity reduces. ####
If there is less than 3 minutes remaining, then will become red. If the battery
discharges, then will flash.
≥Screen display will disappear when no touch operation is performed for a specific period of
time. However, it will be constantly displayed when the remaining battery time becomes less
than 30 minutes.
≥The remaining battery capacity is displayed when using the Panasonic battery that you can
use for this unit. The actual time can vary depending on your actual use.
≥When using the AC adaptor or batteries made by other companies, the remaining battery
capacity will not be shown.

- 14 -
The unit can record still pictures or motion pictures to an SD card. To record to an SD card, read the
following.
Cards that you can use with this unit
∫About the Speed Class ratings for recording motion pictures
≥Depending on [REC MODE] and [REC FORMAT], the required card differs. (l70)
Use a card that meets the following ratings of the SD Speed Class. Use of a non-compatible card
may cause recording to stop suddenly.
≥SD Speed Class is the speed standards regarding continuous writing. To check the class, see the
labelled side, etc. of the card.
≥In the following situations, you need an SD card conforming to Class 10 of the SD Speed
Class Rating to record motion pictures.
Preparation
Recording to a card
Card type Capacity
SD Memory Card 512 MB to 2 GB
SDHC Memory Card 4GB to 32GB
SDXC Memory Card 48 GB/128 GB
≥Please check the latest information on the support website below.
http://panasonic.jp/support/global/cs/e_cam
(This website is in English only.)
≥When using an SDHC Memory Card/SDXC Memory Card with other equipment, check the
equipment is compatible with these Memory Cards.
≥An Eye-Fi X2 series SD card is required to use functions related to Eye-Fi. (l124)
≥We do not guarantee the operation of SD cards other than the ones above. Further, SD cards
with a capacity of less than 32 MB cannot be used for motion picture recording.
≥Operation is not guaranteed for all SD cards.
≥4 GB or more Memory Cards that do not have the SDHC logo or 48 GB or more Memory Cards
that do not have the SDXC logo are not based on SD Memory Card Specifications.
≥When the write-protect switch A on SD card is locked, no recording,
deletion or editing will be possible on the card.
≥Keep the Memory Card out of reach of children to prevent swallowing.
Recording formats Recording modes Speed Class ratings Label examples
MP4/iFrame 1080/50M Class10
1080/28M, 720, iFrame
Class4 or more
AVCHD All
32

- 15 -
Use of a non-compatible card may cause recording to stop suddenly.
jFULL HD Slow Motion Video Mode (l52)
jWhen [Backup for Twin Camera] is set to [ON] (l43)
Inserting/removing an SD card
Caution:
Check that the access lamp has gone off.
1Open the SD card cover and insert
(remove) the SD card into (from)
the card slot B.
≥Face the label side C in the direction shown
in the illustration and press it straight in as far
as it will go.
≥Press the centre of the SD card and then pull
it straight out.
2Securely close the SD card cover.
≥Securely close it until it clicks.
≥Do not touch the terminals on the back of the
SD card.
≥Do not apply strong shocks, bend, or drop the
SD card.
≥Electrical noise, static electricity or the failure
of this unit or the SD card may damage or
erase the data stored on the SD card.
≥When the card access lamp is lit, do not:
jRemove the SD card
jTurn the unit off
jInsert and remove the USB cable
jExpose the unit to vibrations or shock
Performing the above while the lamp is on
may result in damage to data/SD card or this
unit.
≥Do not expose the terminals of the SD card to
water, dirt or dust.
≥Do not place SD cards in the following areas:
jIn direct sunlight
jIn very dusty or humid areas
jNear a heater
jLocations susceptible to significant
difference in temperature (condensation
can occur.)
jWhere static electricity or electromagnetic
waves occur
≥To protect SD cards, return them to their
cases when you are not using them.
≥About disposing of or giving away the SD
card. (l208)
When using an SD card not from Panasonic, or one previously used on other equipment, for the
first time on this unit, format the SD card. (l37) When the SD card is formatted, all of the
recorded data is deleted. Once the data is deleted, it cannot be restored.


Access lamp [ACCESS] A
≥When this unit is accessing the SD card,
the access lamp lights up.

- 16 -
You can turn the unit on and off using the power button or by opening and closing the LCD monitor.
Open the LCD monitor and press the power button to turn on the unit.
AThe status indicator lights on.
The unit is turned on when the LCD monitor is opened, and unit is turned off when it is closed.
During normal use, opening and closing of the LCD monitor can be conveniently used to
turn the unit on/off.
≥The unit will not turn off while recording motion pictures or connecting to Wi-Fi even if the LCD
monitor is closed.
≥In the following cases, opening the LCD monitor does not turn on the unit. Press the power button
to turn on the unit.
jWhen the unit is originally purchased
jWhen you have turned off the unit using the power button
∫Overheat detection
When the internal temperature of the unit rises during use, a message will be displayed. When this
happens, the unit will turn off automatically a few minutes later.
≥Wait until the temperature has dropped before resuming use.
If you try to use the Wi-Fi function while the internal temperature of this unit is high, a message will
be displayed. When this happens, the Wi-Fi function is disabled.
≥Wait until the temperature has dropped before resuming use.
Preparation
Turning the unit on/off
Turning the unit on and off with the power button
Turning the unit on and off with the LCD monitor

To turn off the unit
Hold down the power button until the status
indicator goes off.

- 17 -
You can switch this unit between Recording Mode (Motion Picture Recording Mode/Still Picture
Recording Mode) and Playback Mode by pressing the recording/playback button.
If you touch the recording mode switching icon in Recording Mode, this unit can be switched
between Motion Picture Recording Mode and Still Picture Recording Mode.
Switching this unit between Recording Mode and
Playback Mode
Switching this unit between Motion Picture Recording
Mode and Still Picture Recording Mode
Touch the recording mode switching icon displayed on the LCD monitor (touch screen) to switch this
unit between Motion Picture Recording Mode and Still Picture Recording Mode.
1Press the recording/playback button to
switch this unit to Recording Mode.
≥The recording mode switching icon A is displayed on
the screen.
2Touch the recording mode switching icon.
≥Refer to page 18 for touch screen operation.
Preparation
Selecting a mode
Motion Picture Recording Mode (l22) Recording motion pictures.
Still Picture Recording Mode (l24) Recording still pictures.
Playback Mode (l26, 81) Motion picture/Still picture playback.
Motion Picture Recording Mode
Still Picture Recording Mode
Recording/playback button
Press the button to switch this unit between
Recording Mode and Playback Mode.
≥When you turn on this unit, it starts up in
Recording Mode.
(Motion Picture Recording Mode)

- 18 -
To display the recording mode switching icon
Display of the recording mode switching icon will disappear when no touch operation is performed
for a specific period of time. To display it again, touch the screen.
≥If the recording start/stop button is pressed in Still Picture Recording Mode or Playback Mode,
this unit will be switched to Motion Picture Recording Mode. During motion picture/still picture
playback or in other conditions, even if the recording start/stop button is pressed, the recording
mode may not be switched.
You can operate by directly touching the LCD monitor (touch screen) with your finger.
∫Touch
Touch and release the touch screen to select icon or
picture.
≥Touch the centre of the icon.
≥Touching the touch screen will not operate while you
are touching another part of the touch screen.
∫Slide while touching
Move your finger while pressing on the touch screen.
∫About the operation icons
///:
Touch when changing a page or performing settings.
:
Touch to return to the previous screen.
Preparation
How to use the touch screen

- 19 -
About the Touch Menu
Touch (left side)/ (right side) of on the Touch Menu to switch the
operation icons.
≥It is also possible to switch the operation icons by sliding the Touch Menu right or left while
touching it.
BYou can change the operation icons to display. (l34)
CDisplayed only in Intelligent Auto Plus Mode (l47) and [Miniature Effect]/[8mm movie]/
[Silent movie] of the Creative Control Mode (l47).
DDisplayed only in [Time Lapse Rec] of the Creative Control Mode (l47), Scene Mode
(l51), HDR Movie Mode (l50), FULL HD Slow Motion Video Mode (l52), Stop Motion
Animation Assist Mode (l54) and Manual Mode (l55).
EDisplayed only when you adjust the picture quality with the Multi Manual Dial (l78)
∫To display the Touch Menu
≥Do not touch on the LCD monitor with hard pointed tips, such as ball point pens.
ATouch Menu
Recording Mode Playback Mode
Display of the Touch Menu will disappear when no
touch operation is performed for a specific period of
time during recording of motion picture/still picture. To
display it again, touch .
T
W

MENU
T
W
FOCUS
WB
SHTR
IRIS
  
MENU
ALL

- 20 -
The clock is not set at the time of purchase. Make sure to set the clock.
≥When you turn on this unit, the message “Set home region and date/time.” may be
displayed. Select [YES], and follow the steps below to make these settings:
jStep 3 in [SET WORLD TIME] (l30)
jSteps 2–3 of “Setting date and time”
1Select the menu. (l29)
2Touch the date or time to be set, then set the desired value using /.
ADisplaying the World Time setting (l30):
[HOME]/ [DESTINATION]
≥The year can be set between 2000 and 2039.
3Touch [ENTER].
≥Touch [EXIT] to complete the setting.
≥The date and time function is driven by a built-in lithium battery.
≥If the time display becomes [- -], the built-in lithium battery needs to be charged. To recharge the
built-in lithium battery, connect the AC adaptor or attach the battery to this unit. The battery is still
being recharged even if the unit is off. Leave the unit as it is for approx. 24 hours and the battery
will maintain the date and time for approx. 4 months.
Preparation
Setting date and time
: [SETUP] # [CLOCK SET]
MENU